Question about 1999 Dodge Ram 2500 4WD

1 Answer

Speed sensor 1999 dodge ram 2500 diesel location

Posted by on

Ad

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    Hot-Shot:

    An expert who has answered 20 questions.

    Corporal:

    An expert that has over 10 points.

    Mayor:

    An expert whose answer got voted for 2 times.

  • Expert
  • 72 Answers

On my 99 ram 1500 it is on the right side of the tranny near the end with 2 wires that unplug. I replaced it with no lose of fluid, in 2 minutes.

Posted on Nov 12, 2009

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya Mechanic can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repair professionals here in the US.
click here to Talk to a Mechanic (only for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Location of map sensor on 5.9 diesel 2500 Ram. I think it is on the passenger side of the engin


I don't believe a diesel engine uses a Manifold Absolute Pressure sensor since a diesel engine does not create vacuum.

Feb 15, 2015 | 2003 Dodge Ram Pickup 2500

1 Answer

Transmisson jumps in and out of overdrive at hiway speed is it a sensor?


I had a 2000 2500 (not diesel) there are two sensor. one on the tranny and one near the rear end

Aug 29, 2014 | Dodge Ram 2500 Cars & Trucks

1 Answer

Fireing digram of 1999 dodge ram cummimgs 24 valve 5.9 diesel


Check this firing order for each engine...

1999 Dodge RAM 2500 ¾-Ton Pickup 5.9 liter V-8 VIN "5" HDC

zjlimited_759.gif



1999 Dodge RAM 2500 ¾-Ton Pickup 5.9 liter V-8 VIN "Z" LDC

zjlimited_760.gif


Hope this helps (rememnber to rating this free answer).

Oct 05, 2011 | 1999 Dodge Ram 2500 4WD

1 Answer

Where is the cam sensor on a 1999 dodge ram 4x4 turbo diesel located


cansmo_123.gifIt is located below the fuel injection pump attached to the timing gear cover

Aug 28, 2011 | 1999 Dodge Ram 2500 4WD

1 Answer

EtON 1999 Dodge Ram 2500 4x4 Diesel 5 speed trans. ABS light on, brake light on and speedometer starts working about 20mph.


there is an ABS sensor on top of the rear axle, and they are known to cause these symptoms-check the wiring, connector, and replace it if necessary, they are about $30 and is held in place with one bolt.

Mar 23, 2011 | 1999 Dodge Ram

2 Answers

Where is the speed sensor on a 1999 Dodge Ram 2500 4x4


the wheel speed sensor is on top of rear differental and the output speed sensor is on passenger side tailshaft of transmision.

Nov 21, 2009 | 1999 Dodge Ram 2500 4WD

2 Answers

Where exactly is the crankshaft position sensor 1999 dodge diesel 5.9L


It's bolted to the block, (Cylinder Block), near the rear of the right cylinder head.

Jul 21, 2009 | 1999 Dodge Ram 2500 4WD

1 Answer

What is a Code 84


Hello
Welcome to FY
I would check your speed sensor located on the rear end this is on top of the housing this will throw that code too.
RD

Jan 10, 2009 | 2001 Dodge Ram 2500 Truck

2 Answers

1999 Dodge Ram 2500 Diesel 4x4


there is a cruise control module , easiest way to find it is follow 2nd throttle cable under hood right to it. it most cases there unplugged

Jan 08, 2009 | 1999 Dodge Ram

1 Answer

Clutch position sensor on dodge 2500


Jim, I have the same problem. Looking in my Chilton's manual doesn't help much. But, if you look at the firewall from the driver's seat, where the clutch master cylinder rod goes through the firewall, you will see a plastic cylinder around the rod. There should be a wire that goes from that plastic cylinder and connects into a wiring harness. The manual says that if you separate the clutch position sensor wire from the wiring harness, and jumper the two contacts at that connection in the wiring harness, you will bypass the clutch position sensor switch. I have not yet done this but it is the recommended method of debugging starting problems. If you continue to have problems, I can email to you the section of the Chilton's manual for evaluating the starting system. At least I think I can get my computer to copy this section of the manual. The manual does not give the location of the clutch position sensor but that is the only location i can find that meets the description. I have a 1999 Ram 3500 4WD diesel quad cab.

David Wagner davidwagnerpe@comcast.net

Nov 20, 2008 | 1999 Dodge Ram 2500 4WD

Not finding what you are looking for?
Cars & Trucks Logo

247 people viewed this question

Ask a Question

Usually answered in minutes!

Top Dodge Experts

yadayada
yadayada

Level 3 Expert

77514 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22306 Answers

Ronny Bennett Sr.
Ronny Bennett Sr.

Level 3 Expert

6927 Answers

Are you a Dodge Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...