Question about Nissan Pulsar

1 Answer

I have an 87 nissan pulsar twin cam moter it misses. When i un plug one of the coils it doesnt change anything i switched coils and theirs no diffrence the plug is wet from gas so what could it b?

Posted by on

Ad

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that gotĀ 5 achievements.

    Governor:

    An expert whose answer gotĀ voted for 20 times.

    Hot-Shot:

    An expert who has answered 20 questions.

  • Expert
  • 89 Answers

Have you changed the spark plug ??
just switch with another cylinder ,if problem moved to other cylinder its the plug.if it is still in same cylinder fuel injector is probably stuck open,with engine running
using a bar and hammer tap lightly on injector just enough to vibrate might unstick. could also try Chevron techron fuel injector cleaner as i know it actually works.
if not replace the injector

Posted on Nov 12, 2009

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya Mechanic can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repair professionals here in the US.
click here to Talk to a Mechanic (only for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Where is the coil pack located at on a 1987 Nissan Pulsar. Also spark plugs been changed car still not starting


The link will show you what it looks like. If you follow the leads back from the spark plugs, that will take you to the distributor 9a circular cap with 5 wires). In the centre of the distributer, there is a single lead, follow that one and it will take you to the ignition coil. 1987 Nissan Pulsar NX Ignition Coil Hitachi

Sep 19, 2015 | Nissan Cars & Trucks

1 Answer

Nissan pulsar 1997 temperature guage rising and then the car putts and then cuts out and while idling


I would look at the fan switch plug see if you plugged it back in. You can hear the switch click right before the fan kicks on. Open the hood start the car let it get to operating temp watch the fan make sure it kicks on. If not look at the wired plug that connects to the temp switch if its all secure but the fan doesnt kick on. Look for the relay fuse check it if good then the switch is bad.

Apr 06, 2015 | Nissan Pulsar Cars & Trucks

1 Answer

2004 nissan pulsar st ckp sensor


very common for the N16 pulsars to log this code, this is a crank position sensor fault. 99% of the time is the cam and crank sensors. best to replace them both as a pair, Nissan actually sell them as a pair for this issue, non genuine ones are very un reliable and not much cheeper anyways. the cam sensor is in the back side of the head above the bell housing of gearbox and the crank sensor is in the bottom of the engine block at the gearbox end facing the firewall.
the other 1% is streatched orout of timed timing chains, but normally just the sensors will fix it.

Jan 12, 2014 | Cars & Trucks

1 Answer

Car has no spark to plugs


run fault codes and look for a cam/ crank sensor problem. Check that the immobiliser is recognising your key

Nov 16, 2013 | 1990 Nissan Pulsar

1 Answer

1991 n13 nissan pulsar 1.6 liter motor I have just replaced the distributer and coil but I am still gettin no spark what do I do


Did you even bother to check and see if the distributor and coil had any battery power to work with before you blamed them for the problem and sent them to their grave? I'm So-o-o-o-o glad I'm not an auto part....No such thing as a fair trial where facts must be presented and proven before you can be locked (thrown) away......

It could be anything in the ignition circuit, including the ignition switch itself or a break in any of the many wires involved....Proper diagnosis required.

May 28, 2012 | 1990 Nissan Pulsar

1 Answer

The vacuum lines in my 87 pulsar twin cam 16 valve are misplaced and missing. i need an easy exploded diagram that is for dumbies.


email me at iambanshee74@yahoo.com and I will send you the daigrams. You will need to know the name of the parts, but this should work for you and if you need anything else, just let me know. Send me the engine size/family which can be found on the emissions sticker under the hood and whether it is a California car or Federal emissions.

Apr 30, 2010 | 1987 Nissan Pulsar

1 Answer

Do you have to mess with the timing to replace the water pump in a 87 pulsar?


honestly dont know ,the vehicle name doesnt mean anything but the engine type would .is it petrol or diesel .cc all the info needed

Dec 22, 2009 | 1987 Nissan Pulsar

1 Answer

No spark from 1988 nissan pulsar


BOT MA MAY B ,,,, BUT FIRST CHECK FUSEZ ,,,,, HAVE CHECKED POINT ?

Jul 22, 2009 | 1988 Nissan Pulsar

3 Answers

Car wont start


HI MATE SOUNDS LIKE CRANK SENSOR HAD THE SAME PROBS WITH A SKYLINE

Jun 16, 2008 | 1990 Nissan Pulsar

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

154 people viewed this question

Ask a Question

Usually answered in minutes!

Top Nissan Experts

yadayada
yadayada

Level 3 Expert

77514 Answers

Phil Lovisek
Phil Lovisek

Level 3 Expert

726 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22306 Answers

Are you a Nissan Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...