Will a 95 GT4 s/s exhaust fit 97 GT 2.0 st2o2

You would need way more than Steven said. So no. Don't use it.

Block and Basics
Displacement: 350 cubic inches, 5733 cubic centimeters, 5.7 liters
Block Material: Cast Iron
Main Bearings: 2-Bolt Centers and Ends (The Corvette LT1/LT4 had 4-bolt mains)
Stroke: 3.48"
Bore: 4.00"
Compression Ratio: 10.4:1
Combustion Chambers: 54 cubic centimeters
Factory Redline Rating: 5700 Rotations Per Minute

Bottom End
Piston Material: (10159437) Eutectic Aluminum/Silicon Alloy
Connecting Rod Material: (10108688) Powdered Metal
Crankshaft Material: (12556307) Cast Iron

Top End and Valvetrain
Cylinder Heads: (10168448) Cast Aluminum, 2 valves per cylinder/16 valves total, ~212 CFM flow (Impala SS and Caprice heads were made of cast iron*)
Valve Diameter: (intake- 10241743, exhaust- 12550909) 1.94 intake, 1.50 exhaust
Valve Overlap: 41*
Valvesprings: (10206040) 85 lbs, seated
Camshaft Specs (12551705): 205/207 duration @ 50*, .447/.459" lift, 117 Lobe Seperation Angle
Rocker Arms: (10089648) 1.5:1 Stamped Steel
Timing Chain: (10128485) Powdered metal link

Intake and Fuel Delivery
Fuel Delivery: Electronic Fuel Injection, sequential port
Injector Size: (17124248) 3.0gps, 22lbs/hr speed density (1992-1993), 24lbs/hr mass airflow (1994-1997)
Throttle Body: 48 millimeter twin butterfly
Intake Manifold: (12552137) Aluminum

Factory Power Ratings
92-96 LT1 Corvette: 300bhp, 330lb-ft
1996 LT4 Corvette: 330bhp, 340lb-ft
1992 LT5 Corvette: 375bhp, 370lb-ft
93-95 LT5 Corvette: 405bhp, 385lb-ft
93-95 LT1 F-Body: 275bhp, 325lb-ft
96-97 LT1 F-Body: 285bhp, 325lb-ft
96-97 WS6/SS: 305bhp, 335lb-ft
93-97 Firehawks: 315bhp, 340lb-ft

Factory LTX Camshaft Specifications**:
1992 Y-body: 205/207 0.451/0.450 lift 117 LSA
1993-1995 Y-body, F-body: 202/207 0.450/0.460 lift 116 LSA
1994-1996 B-bodies (including L99 4.3L): 191/196 0.418/0.430 lift 111 LSA
1996 Y-body, 1996-1997 F-body: 200/207 0.447/0.459 lift 117 LSA
1996 Y-body, F-body LT4: 203/210 0.476/0.479 lift 115 LSA


hope this helps

check with a dealer parts department or junk yard

They will swap out.

yes the exhaust system from 97 will fit with 99 they are compatible but removing it and replacing it with new is bit mechanical job.a professional technicians help is very much required in this time consuming job. This will help. Thanks please keep updated.please do rate the solution positively .thank you for using fixya

yes this will fit, model years 88-97 will fit. I would recommend the newest model you can get, as they improved internal hardware after 93. hopefully this helps

depends on the engines,call a scrap yard and ask what the interchanges are,or possibly an auto parts store

http://www.allfordmustangs.com/forums/attachments/94-95-tech/608d1036338026-need-fuse-box-diagram-95-gt-esb01113.gif


hope that helps.

95-94-93 4.3 vortec are compatable engines. 97 4.3 will fit but will have problems with sensors and computer

There is no problem with your computer box, it says 3S-GT on it, thats the way toyota did them back then. same with the 3S-FE (says 3S-F on the comp. box) and 3S-GE (3S-G on comp. box.) i dont recommend removin the cat. you will get defected (or waht is equivelant to a defect where you are) due to smog and stuff like that. Turbo timer is wired to the igntion system, no problems there. and as for gauges: get a pro to install them, but there should be zero trouble.