Wipers inoperative. Replaced motor, but still will not work. How do you change the wiper control module? I have also checked the fuses.

Rear Wiper/Washer System Components
The rear wiper/washer system consists of the following components:
• Rear wiper/washer switch
• Window wiper module-rear
• Window washer pump-rear
• RR WIPER 15A fuse
• RR WPRB 25A fuse
Rear Wiper/Washer System Operation
The rear wiper module controls rear wiper motor operation. Battery voltage supplied to the module is used to operate the wiper motor in all modes and to return the rear wiper arm to the park position after the ignition is turned off. Accessory voltage supplied to the rear wiper/washer switch is used to supply the rear window wiper and washer switch signal circuits. In wiper switch positions 1 and 2 the wiper switch signal circuit voltage level to the wiper motor module determines the wiper motor delay interval. The rear window washer pump supply voltage circuit is used to provide the operating voltage for the rear washer pump for as long as the rear washer switch is pressed. The rear window washer switch signal circuit is used as a wash signal to the rear wiper motor module to operate the wipers during the rear wash operation.


Did you replace the rear wiper module ?

Highly doubtful it being a blown fuse . Fuse's don't just blow , short circuit to ground or high current draw . Faulty component , wiper motor , wiper control module more likely . Free wiring diagrams here http://www.bbbind.com/free-tsb Enter vehicle info. year , make , model an engine size . Under system click on body & accessories . then under subsystem click on wiper / washer , Click the search button ,then the blue link . Looking at the diagram i see the wiper switch is a input to the wiper control module .

The windshield wipers are controlled by the wiper control module and the driver-operated multi-function switch on the steering column, with the ignition switch in RUN or ACC position.
There are four modes of wiper operation: OFF position, the wipers move to and stay in the park position; Interval position, the wiper control module causes the wipers to cycle, separated by pauses, pause time length being determined by switch location; LO position, the wipers will operate at low speed continuously; HI position, the wipers will operate at high speed continuously.
The windshield washers are controlled by pressing inward on the wiper switch end of the multi-function switch. The washers will operate as long as the switch is depressed. If the wipers are in the OFF or Interval operating mode, the wipers will begin in LO speed and the washer pump will pump fluid from the reservoir to the nozzles. When the switch is released, the wipers will complete three cycles and then return to their previous setting. In LO or HI mode, no change in wiper operation will occur during washer operation.
The washer fluid level sensor is in the windshield washer reservoir (17618) and is monitored by the hybrid electronic instrument cluster (HEC) and displays a WASHER message when the fluid level is low. The washer fluid level sensor and windshield washer reservoir are replaced as an assembly.

• The Wipers are Inoperative

• Fuse.
• Wiper motor.
• Multi-function switch.
• Circuitry.
• Wiper control module.

• GO to Pinpoint Test B .

PINPOINT TEST B: THE WIPERS ARE INOPERATIVE CONDITIONS DETAILS/RESULTS/ACTIONS B1 CHECK FUSE JUNCTION PANEL FUSE 16 (30A)
Fuse 16 (30A)

• Is the fuse OK?

Yes GO to B2 .

No REPLACE the fuse. TEST the system for normal operation. If the fuse fails again, CHECK for a short to ground. REPAIR as necessary. B2 CHECK FOR VOLTAGE TO THE WIPER CONTROL MODULE - CIRCUIT 65 (DG)
Wiper Control Module C294
Measure the voltage between wiper control module C294-2, circuit 65 (DG), and ground; and between wiper control module C294-11, circuit 65 (DG), and ground.

• Is the voltage greater than 10 volts?

Yes GO to B3 .

No REPAIR circuit 65 (DG). TEST the system for normal operation. B3 CHECK CIRCUIT 57 (BK) FOR OPEN Measure the resistance between wiper control module C294-3, circuit 57 (BK), and ground; and between wiper control module C294-5, circuit 57 (BK), and ground.

• Are the resistances less than 5 ohms?

Yes GO to B4 .

No REPAIR circuit 57 (BK). TEST the system for normal operation. B4 CHECK THE MULTI-FUNCTION SWITCH
Multi-Function Switch
Check the multi-function switch; refer to Section 211-05 .

• Is the multi-function switch OK?

Yes GO to B5 .

No REPLACE the multi-function switch; REFER to Section 211-05 . TEST the system for normal operation. B5 CHECK CIRCUIT 993 (BR/W) FOR OPEN Measure the resistance between multi-function switch C269-4, circuit 993 (BR/W), and wiper control module C294-7, circuit 993 (BR/W).

• Is the resistance less than 5 ohms?

Yes GO to B6 .

No REPAIR circuit 993 (BR/W). TEST the system for normal operation. B6 CHECK CIRCUIT 589 (O) FOR OPEN Measure the resistance between multi-function switch C269-1, circuit 589 (O), and wiper control module C294-1, circuit 589 (O).

• Is the resistance less than 5 ohms?

Yes GO to B7 .

No REPAIR circuit 589 (O). TEST the system for normal operation. B7 CHECK THE WIPER CONTROL MODULE OUTPUT FOR VOLTAGE
Wiper Control Module C294

Wiper Motor C152
Turn the multi-function switch to the HI position. Measure the voltage between wiper motor C152-4, circuit 57 (BK), and wiper motor C152-3, circuit 56 (DB/O).

• Is the voltage greater than 10 volts?

Yes REPLACE the wiper motor; REFER to Motor-Windshield Wiper . TEST the system for normal operation.

No GO to B8 . B8 CHECK CIRCUIT 57 (BK) FOR OPEN Measure the resistance between wiper motor C152-4, circuit 57 (BK), and ground.

• Is the resistance less than 5 ohms?

Yes REPLACE the wiper control module; REFER to Module-Windshield Wiper . TEST the system for normal operation.

No REPAIR circuit 57 (BK). TEST the system for normal operation.

Wiper relays (2) on/off relay an speed relay , location battery junction box . Look at the wiring diagram here http://www.bbbind.com/free_tsb.html Enter vehicle info. year , make , model and engine . System click body & accessories , subsystem click wipers/washers . Click the search button , then the blue link . After viewing the wiring diagram for the wipers , Change systems to electrical distribution , then click junction block . Then the search button an first blue link . Shows the relay position . The wiper switch is a input to the front electronic control module . The relays are also controlled by the electronic control module . Probably has code set in the module . You would need a factory scan tool to check this .

Did you check the wiper relay's in the under hood fuse box ? There are two ,wiper run/park relay & wiper high low relay ! Also ,did you check fuse's ? fuse # 11 - 30amp location cental juction box . The wiper switch is a input to the GEM module . Generic electronic module . The module in most cases isn't the problem ! Learning how to test these electronic systems is , people do not know how to test so they just replace parts . What they should do is take the vehicle to ford certified Technician who has the knowledge and testing equipment to find an fix it .

The generic electronic module (GEM) receives inputs from the following:

• multifunction switch
• anti-lock brake control module (vehicle speed signal [VSS])
• ignition switch

The GEM uses these inputs to control the outputs to the following:

• windshield wiper high/low relay
• windshield wiper run/park relay
• windshield washer relay
• rear wiper motor relay
• rear window washer relay
• 
  GEM Diagnostic Trouble Code (DTC) Index DTC Description Source Action B1240 Wiper Washer Rear Pump Relay Circuit Failure GEM GO to Pinpoint Test K . B1241 Wiper Washer Rear Pump Relay Circuit Short to Battery + GEM GO to Pinpoint Test K . B1342 ECU is Defective GEM CLEAR the DTCs. REPEAT the GEM self-test. If DTC B1342 is retrieved, INSTALL a new GEM. REFER to Section 419-10 . B1431 Wiper Brake/Run Relay Circuit Failure GEM If the windshield wipers are inoperative, GO to Pinpoint Test B .
  If the windshield wipers stay on continuously, GO to Pinpoint Test C . B1432 Wiper Brake/Run Relay Circuit Short to Battery GEM GO to Pinpoint Test B . B1434 Wiper Hi/Low Speed Relay Coil Circuit Failure GEM GO to Pinpoint Test D . B1436 Wiper Hi/Low Speed Relay Coil Circuit Short to Battery GEM GO to Pinpoint Test D . B1438 Wiper Mode Select Switch Circuit Failure GEM If the windshield wipers are inoperative, GO to Pinpoint Test B .
  If both the windshield and rear window wipers are inoperative, GO to Pinpoint Test L . B1441 Wiper Mode Select Switch Circuit Short to Ground GEM GO to Pinpoint Test C . B1446 Wiper Park Sense Circuit Failure GEM If the intermittent windshield wiper speed does not operate correctly, GO to Pinpoint Test E .
  If the speed dependent interval mode does not operate correctly, GO to Pinpoint Test G .
  If both windshield and rear wipers are inoperative, GO to Pinpoint Test L . B1450 Wiper Wash/Delay Switch Circuit Failure GEM If the intermittent windshield wiper speed does not operate correctly, GO to Pinpoint Test E .
  If the wash and wipe function does not operate correctly, GO to Pinpoint Test F .
  If both the windshield and rear wipers are inoperative, GO to Pinpoint Test L . B1453 Wiper Wash/Delay Switch Circuit Short to Ground GEM If the windshield wipers stay on continuously, GO to Pinpoint Test C .
  If the wash and wipe function does not operate correctly, GO to Pinpoint Test F . B1458 Wiper Washer Pump Motor Relay Circuit Failure GEM GO to Pinpoint Test F . B1460 Wiper Washer Pump Motor Relay Coil Circuit Short to Battery GEM GO to Pinpoint Test F . B1473 Wiper Low Speed Circuit Motor Failure GEM If the windshield wipers are inoperative, GO to Pinpoint Test B .
  If the windshield wipers do not operate at high or low speed correctly, GO to Pinpoint Test D .
  If the intermittent windshield wiper speed does not operate correctly, GO to Pinpoint Test E . B1475 Accessory Delay Relay Contact Short to Battery GEM REFER to Section 501-11 . B1476 Wiper High Speed Circuit Motor Failure GEM If the windshield wipers are inoperative, GO to Pinpoint Test B .
  If the windshield wipers do not operate at high or low speed correctly, GO to Pinpoint Test D .
  If the intermittent windshield wiper does not operate correctly, GO to Pinpoint Test E . B1611 Rear Wiper Mode Switch Circuit Failure GEM GO to Pinpoint Test H . B1614 Rear Wiper Mode Switch Circuit Short to Ground GEM GO to Pinpoint Test I . B1820 Rear Wiper Motor Up Relay Circuit Short to Battery + GEM GO to Pinpoint Test H . B1839 Rear Wiper Motor Circuit Failure GEM GO to Pinpoint Test H . - All other DTCs. GEM REFER to Section 419-10

Wd40 of gt85 tray that first

Have you done a Probe Test on the vehicle? A Probe Light Tester can help you locate a short in your cars electrical system. To learn what a Probe Tester is and How to use it, watch the following video: https://www.youtube.com/watch?v=tXzKcEyIOq8

Check your fuse cluster(s) for open fuse (s).

Did you check for voltage at the wiper fuse? My info says that fuse is hot all the time. Use a digital multimeter. Everything off, take a reading across battery posts, the generic spec for a full charge is around 12.6 volts. You should get close to same reading at the wiper fuse, hopefully. When checking voltage at the fuse, use chassis ground not the other leg of fuse. There are wiper relays, those are pcb relays, they are soldered into the fuse box, you can't pull them out. Your bcm is also involved with those relays. Your multifunction switch basically tells the bcm you turned on your wipers, then the bcm controls voltage or ground for the relays. You can see wire color for hi and lo speed voltage. Maybe a problem with fuse box or wiring circuit if voltage is low? I hope this was of some help?

the wipers are controlled by the lighting control module

The wiper control module is probably at fault ,without test that is just a guess . The wiper/washer switch is a input to the wiper control module. Do you know anything about automotive electronics an electrical systems ?

• The Wipers are Inoperative

• Fuse.
• Wiper motor.
• Multi-function switch.
• Circuitry.
• Wiper control module.

• GO to Pinpoint Test B .

Voltage drop testing the power an ground circuits for the wiper control module would be a good place to start . Do you know how to test electrical circuits with a volt meter ?
PINPOINT TEST B: THE WIPERS ARE INOPERATIVE CONDITIONS DETAILS/RESULTS/ACTIONS B1 CHECK FUSE JUNCTION PANEL FUSE 16 (30A)
Fuse 16 (30A)

• Is the fuse OK?

Yes GO to B2 .

No REPLACE the fuse. TEST the system for normal operation. If the fuse fails again, CHECK for a short to ground. REPAIR as necessary. B2 CHECK FOR VOLTAGE TO THE WIPER CONTROL MODULE - CIRCUIT 65 (DG)
Wiper Control Module C294
Measure the voltage between wiper control module C294-2, circuit 65 (DG), and ground; and between wiper control module C294-11, circuit 65 (DG), and ground.

• Is the voltage greater than 10 volts?

Yes GO to B3 .

No REPAIR circuit 65 (DG). TEST the system for normal operation. B3 CHECK CIRCUIT 57 (BK) FOR OPEN Measure the resistance between wiper control module C294-3, circuit 57 (BK), and ground; and between wiper control module C294-5, circuit 57 (BK), and ground.

• Are the resistances less than 5 ohms?

Yes GO to B4 .

No REPAIR circuit 57 (BK). TEST the system for normal operation. B4 CHECK THE MULTI-FUNCTION SWITCH
Multi-Function Switch
Check the multi-function switch; refer to Section 211-05 .

• Is the multi-function switch OK?

Yes GO to B5 .

No REPLACE the multi-function switch; REFER to Section 211-05 . TEST the system for normal operation. B5 CHECK CIRCUIT 993 (BR/W) FOR OPEN Measure the resistance between multi-function switch C269-4, circuit 993 (BR/W), and wiper control module C294-7, circuit 993 (BR/W).

• Is the resistance less than 5 ohms?

Yes GO to B6 .

No REPAIR circuit 993 (BR/W). TEST the system for normal operation. B6 CHECK CIRCUIT 589 (O) FOR OPEN Measure the resistance between multi-function switch C269-1, circuit 589 (O), and wiper control module C294-1, circuit 589 (O).

• Is the resistance less than 5 ohms?

Yes GO to B7 .

No REPAIR circuit 589 (O). TEST the system for normal operation. B7 CHECK THE WIPER CONTROL MODULE OUTPUT FOR VOLTAGE
Wiper Control Module C294

Wiper Motor C152
Turn the multi-function switch to the HI position. Measure the voltage between wiper motor C152-4, circuit 57 (BK), and wiper motor C152-3, circuit 56 (DB/O).

• Is the voltage greater than 10 volts?

Yes REPLACE the wiper motor; REFER to Motor-Windshield Wiper . TEST the system for normal operation.

No GO to B8 . B8 CHECK CIRCUIT 57 (BK) FOR OPEN Measure the resistance between wiper motor C152-4, circuit 57 (BK), and ground.

• Is the resistance less than 5 ohms?

Yes REPLACE the wiper control module; REFER to Module-Windshield Wiper . TEST the system for normal operation.

No REPAIR circuit 57 (BK). TEST the system for normal operation.