Question about 2007 Toyota Camry

1 Answer

2007 camry serpentine belt installation - 2007 Toyota Camry

Posted by on

Ad

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Expert
  • 301 Answers

Http://www.gates.com/part_locator/index.cfm?location_id=3002

Go here and enter the info for your vehicle. Since I have no idea if you have a 4 or 6 cylinder engine you must look it up then click the photo icon next to the serpentine belt listing. They have belt routing drawings there.

Posted on Oct 18, 2009

Ad

5 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad
s_chev
  • 15 Answers

SOURCE: how to remove the serpentine belt of a 2004 toyota

Actually you don't have to do all of that. I just replaced one from the top. On the passenger side of the engine where the belt is, you will see the tensioner in the middle. Using a larger breaker bar with the socket that fits the bolt in the middle of the wheel, force the tensioner toward the front of the car to release pressure to remove the belt. I think it was a 15mm but can't remember for sure. I do know they are all metric sizes on that engine. The tricky part is to remember how the belt is routed. If you forget, see the diagram below. There isn't much room to work, but I'm proof that it is possible. When putting the new best on, route all pulleys and leave the alternator for last since it's right on top and easy to get to. Good luck and be patient. It's doable.85ddd91.jpg

Posted on Apr 12, 2010

abauto
  • 353 Answers

SOURCE: how do i change a serpentine belt for a 2007

Drive Belt: Service and Repair
DRIVE BELT

Components
43931e7.jpg


REMOVAL
1. REMOVE V-BANK COVER SUB-ASSEMBLY
2. REMOVE NO. 1 ENGINE UNDER COVER

4cff58f.jpg



3. REMOVE FAN AND GENERATOR V BELT
(a) While turning the belt tensioner counterclockwise, align the service hole for the belt tensioner and the belt tensioner fixing position, and
then insert a bar of [diameter]5 mm (0.197 in.) into the service hole to fix the belt tensioner in place.
HINT: The pulley bolt for the belt tensioner has a left-hand thread.
(b) Remove the V belt.



1. INSTALL FAN AND GENERATOR V BELT
(a) Set the V belt onto every part.
(b) While turning the belt tensioner counterclockwise, remove the pin.
NOTICE: Make sure that the V belt is properly set to each pulley.
(c) After installing the belt, check that it fits properly in the ribbed grooves.
HINT: Make sure to check by hand that the belt has not slipped out of the grooves on the bottom of the pulley.
2. INSTALL NO. 1 ENGINE UNDER COVER
3. INSTALL V-BANK COVER SUB-ASSEMBLY

c0b77ac.jpg

Posted on Sep 30, 2009

  • 484 Answers

SOURCE: how to change serpentine belt on 207 toyota camry

4 cylinder diagram
6 cylinder diagram
Loosen the tensioner pulley to remove the belt. It is the one that has a long bolt running through it. Once you remove the old belt, install the new one using the appropriate diagram from the above two links. Readjust the tension using the bolt you loosened to remove the old belt.

i hope this helps
matthew

Posted on Nov 20, 2009

  • 538 Answers

SOURCE: 2007 chrysler sebring serpentine belt diagram

Go to; daycoproducts.com, click cars and trucks, then go to serpentine belt. Then on the right side of the screen click on finding your vehicle. Then get the illistration number and click on illistrations, go to that number it should something 6-? or 7-?. It's a pretty good websight.

Posted on Jan 31, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Serpentine diagram for 2gr-fe


Toyota Camry 2007 2011 How to Replace Serpentine Belt Tensioner If you don't need to replace the tensioner, just skip down to where the belt wrap diagram is.

Sep 09, 2016 | 2007 Toyota Camry

2 Answers

HDo I remove and install an idler pulley on a 2005 Toyota Camry?


How to replace drive belt tensioner Toyota Camry - YouTube

? 4:26
https://www.youtube.com/watch?v=gfSJvN-CE2E
Feb 22, 2013 - Uploaded by Fix It Angel
2002 2003 2004 2005 2006 2007 2008 2009 Toyota Camry. Engine, 4 cylinder, 2.4L, 2AZ-FE. 2004 Toyota ...

Idler Pulley, How to replace (EASY and CHEAP) - YouTube

? 4:56
https://www.youtube.com/watch?v=axAltpW8wR4
Nov 2, 2013 - Uploaded by ChrisFix
Idler pulley squeak? Learn how to fix a squeaky pulley in your car. The serpentine belt in your car powers the ...

2007 Camry Serpentine Belt Replace - 4 Cyl, 2.4 liter ...

? 4:21
https://www.youtube.com/watch?v=ejhyCrh96a8
Jan 13, 2013 - Uploaded by Flyin Brian
I show you step-by step how to get the old belt off and install a new ... ... Water pump replacement 2007 Toyota ...


Jan 27, 2016 | Toyota Cars & Trucks

1 Answer

How do I change alternator in 2007 Camry SE V6. I've removed the belt and appropriate bolts but I'm having trouble removing the alternator from the mounting bracket that connects the top of th


Changing alternator on 2007 camry v6
1) remove cover on top of the rad support.
2) remove air intake pipe that goes to air filter
3) remove hood lock mechanism
4) remove bar that is situated on top of radiator
5) remove electric part from rad fan
6) remove rad fan
7) remove rad hoses
8) remove serpentine belt, remember the route of belt
9) remove two bolts one from top and one from bottom on alternator no14
10) very important that there is a bracket that attaches alternator to the engine block, remove that bracket and take out the alternator from top
Installation, just put everything back
Hope this helps good luck

Nov 02, 2014 | Cars & Trucks

1 Answer

How do I change an alternator On a 2007 Toyota Camry SE V6


Changing alternator on 2007 camry v6
1) remove cover on top of the rad support.
2) remove air intake pipe that goes to air filter
3) remove hood lock mechanism
4) remove bar that is situated on top of radiator
5) remove electric part from rad fan
6) remove rad fan
7) remove rad hoses
8) remove serpentine belt, remember the routine of belt
9) remove two bolts one from top and one from bottom on alternator no14
10) very important that there is a bracket that attaches alternator to the engine block, remove that bracket and take out the alternator from top
Installation, just put everything back
Hope this helps good luck

Jun 16, 2012 | Cars & Trucks

1 Answer

Serpentine belt diagram, 2004 toyota camry


This is more of a question than an answer,..but it appears no one seems to know anything about identifying which serpentine belt to use,..there are two listed for the 2004 Toyota Camry 2.4 liter engine. One belt is designed for engines with the "enhancement" and another belt was designed for 2.4 liter engines WITHOUT the "enhancement" My question here is,..How do you know if your 2004 Toyota Camry has this "Enhancement" installed or not.

Feb 09, 2012 | 2004 Toyota Camry

1 Answer

I am try to replace the serpintine belt for the power steering on


This answer is for a 2003 Toyota Camry listed by the Asker under the 2001 Toyota Avalon Category

Click on the following direct Link. It has the Serpentine Belt Diagram.

Standard Rules to Removal the Serpentine Belt with a Tensioner:
1. Find the Tensioner(s). (See Diagrams on Link)
2. Using a Serpentine Belt Tensioner Tool, Or Wrench OR Ratchet, Rotate/Move the Tensioner USING THE AVAILABLE NUT (on the Pulley or Arm Base) OR the OPENING (3/8ths or 1/2 inch square opening) rotating the Tensioner Pulley/Arm - moving it away from contact with the belt and towards the area where the belt is not in contact with the Tensioner Pulley. The Tensioner is spring loaded, and is hard to rotate/move.
3. Remove the loosened belt off one of the other more easily accessed Pulleys.
4. DO NOT quickly release the Tensioner, but gently allow the Tensioner to rest in its closed position.

Standard Rules for Installing the Serpentine Belt with Tensioners:
a. Pick a Pulley that is most easily accessed. This will usually be on top. This will be the last Pulley that the belt will go on.
b. Using the Diagram: Install the new Serpentine Belt on the remainder of the Pulleys....over, under, left right.
c. Using a Serpentine Belt Tensioner Tool or Wrench or Ratchet Tool: Rotate/Move the Tensioner Pulley/Arm "away" from Belt contact area on the Tensioner. This spring is pretty hard and with a new belt, it will be even harder to install. Rotate/Move this to as-close to the maximum allowed inorder to have enough slack in the belt to get it up and over the last pulley.
d. Using your other hand - Pull the Belt up and over the Last remaining Pulley.
e. Before releasing the pressure on the Tensioner, visually inspect the remainder Pulleys and the Belts' Positioning on them

Let me know if this helped, or if you have additional information or questions. Feel Free to contact me at FixYa.Com!

http://www.2carpros.com/car_repair_information/year/2003/make/toyota/model/camry/2003_toyota_camry_drive_belt_routing_diagram.htm

Mar 21, 2010 | 2001 Toyota Avalon

1 Answer

How do you remove the drive belt of a 2003 Toyota


Click on the following free direct Link. It has the correct Serpentine/Drive Belt Diagrams for your 2003 Toyota Camry with either the 2.4L 4-Cylinder or 3.0L V6 Engine.

http://www.2carpros.com/car_repair_information/year/2003/make/toyota/model/camry/2003_toyota_camry_drive_belt_routing_diagram.htm

"HOW TO":
Standard Rules to Removal the Serpentine Belt with an Automatic Tensioner:
1. Find the Tensioner(s). (See Diagrams on Link)
2. Using a Serpentine Belt Tensioner Tool, Or Wrench OR Ratchet, Rotate/Move the Tensioner USING THE AVAILABLE NUT (on the Pulley or Arm Base) OR the OPENING (3/8ths or 1/2 inch square opening) rotating the Tensioner Pulley/Arm - moving it away from contact with the belt and towards the area where the belt is not in contact with the Tensioner Pulley. The Tensioner is spring loaded, and is hard to rotate/move.
3. Remove the loosened belt off one of the other more easily accessed Pulleys.
4. DO NOT quickly release the Tensioner, but gently allow the Tensioner to rest in its closed position.

Standard Rules for Installing the Serpentine Belt with an Automatic Tensioner:
a. Pick a Pulley that is most easily accessed. This will usually be on top. This will be the last Pulley that the belt will go on.
b. Using the Diagram: Install the new Serpentine Belt on the remainder of the Pulleys....over, under, left right.
c. Using a Serpentine Belt Tensioner Tool or Wrench or Ratchet Tool: Rotate/Move the Tensioner Pulley/Arm "away" from Belt contact area on the Tensioner. This spring is pretty hard and with a new belt, it will be even harder to install. Rotate/Move this to as-close to the maximum allowed inorder to have enough slack in the belt to get it up and over the last pulley.
d. Using your other hand - Pull the Belt up and over the Last remaining Pulley.
e. Before releasing the pressure on the Tensioner, visually inspect the remainder Pulleys and the Belts' Positioning on them.

Let me know if this helped, or if you have additional information questions. Feel Free to contact me at FixYa.com!

Dec 29, 2009 | 2003 Toyota Camry

1 Answer

How to change serpentine belt on 207 toyota camry


4 cylinder diagram
6 cylinder diagram
Loosen the tensioner pulley to remove the belt. It is the one that has a long bolt running through it. Once you remove the old belt, install the new one using the appropriate diagram from the above two links. Readjust the tension using the bolt you loosened to remove the old belt.

i hope this helps
matthew

Nov 20, 2009 | 2007 Toyota Camry

2 Answers

Need diagram for toyota camry 2002 2.4 serpentine belt.


2003 TOYOTA CAMRY Serpentine Belt Diagram

Jul 27, 2008 | 2003 Toyota Camry

Not finding what you are looking for?
2007 Toyota Camry Logo

6,004 people viewed this question

Ask a Question

Usually answered in minutes!

Top Toyota Experts

Marvin
Marvin

Level 3 Expert

83940 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22441 Answers

Jeffrey Turcotte
Jeffrey Turcotte

Level 3 Expert

8841 Answers

Are you a Toyota Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...