How do you replace the Serpentine Drive Belt - 2002 GMC Envoy

VIDEO Change Serpentine Poly Drive Belt tensioner on Mercedes Benz...

Serpentine Belt Replacement

Replacing Your Mercedes Belt Tensioner

mercedes benz serpentine belt diagram

kia forte drive belt - Kia Forte Forum : Sedan / Koup / Forte5 Forums

www.forteforums.com/.../kia-forte-2-0l.../40769-kia-forte-drive-belt.htm...

Dec 19, 2013 - 8 posts - ‎3 authors
im trying to replace the drive belt on a 2010 kia forte ex 2.0l and was wondering if someone could get me a diagram of the belt routing as well ... Squeal in serpentine belt area even after replacing ...
3 posts
Nov 8, 2014
Serpentine drive belt -very frustrating-
15 posts
Jun 17, 2014
Recommended mileage timing chain change SX
11 posts
Mar 23, 2014
Serpentine belt removal on a 2.4L. Anyone?
5 posts
Aug 11, 2013
More results from www.forteforums.com
images for serpentine belt diagram on a 2010 Kia Forte

How To Change The Serpentine Accessory Belt On Nissan Maxima Altima Etc

Nissan Drive Belt Tensioner and Belt Replacement 3 5 Front Wheel Drive

There are several videos on how to change out the serpentine belt For more info just do a web search " 2002 Nissan Altima serpentine belt replacement".

Application:
With A/C

Kia_Sedona_2002-2006
Accessory Drive Belts

• ACCESSORY BELT ROUTING
• INSPECTION
• REMOVAL & INSTALLATION

Print

Accessory Belt Routing

Fig. Accessory serpentine belt routing-3.5L engine

Fig. Accessory serpentine belt routing-3.5L engine

Fig. Accessory serpentine belt (A) routing-3.8L engine

Inspection

Inspect the drive belt for signs of glazing or cracking. A glazed belt will be perfectly smooth from slippage, while a good belt will have a slight texture of fabric visible. Cracks will usually start at the inner edge of the belt and run outward. All worn or damaged drive belts should be replaced immediately.

Removal & Installation

1. Disconnect the negative battery cable.
2. Rotate the auto tensioner clockwise to release tension, then remove the drive belt.

To install:

1. Install drive belt (A). Route the belt over the components in the following order: Crankshaft pulley - A/C pulley - idler pulley - generator pulley - water pump pulley - P/S pump pulley - tensioner pulley.
2. Rotate auto tensioner arm in the counter-clockwise moving auto tensioner pulley bolt with wrench.
3. After putting belt on auto tensioner pulley, release the auto tensioner pulley slowly.
   
   

   Fig. Accessory serpentine belt routing-3.5L engine
   
   
   

   Fig. Accessory serpentine belt (A) routing-3.8L engine
   

Fig. Serpentine accessory drive belt routing-3.0L (VIN U) engine


Fig. Serpentine accessory drive belt routing-3.0L (VIN S) engine


Fig. Serpentine accessory drive belt routing-Ford 3.0L (VIN U) engines


Fig. Serpentine accessory drive belt routing-Ford 3.0L (VIN S) engine


Fig. Serpentine accessory drive belt routing-Ford 3.4L SHO engine


Fig. Water pump drive belt routing-Ford 3.4L SHO engine
i wasnt sure what engine you had hope this helps good luck

e



Fig. Accessory drive belt routing-3.0L engine




Fig. Accessory serpentine belt routing-3.0L engine




Fig. Accessory serpentine belt routing-3.8L engine


Removal and Installation



Fig. Drive belt tensioner wear indicator marks




Fig. Place a wrench on the drive belt tensioner bolt and rotate the assembly clockwise to relieve belt tension

Using a 15mm wrench attached to the drive belt tensioner pulley, rotate the tensioner clockwise to release the tension. Remove the drive belt from the pulley. When installing the new drive belt, ensure that the drive belt is routed correctly and note the position of the indicator mark on the tensioner.

Hope heled with this; remember rated this help. Good luck.

First, keep this link which is to the diagram of the serpentine belt. It will be useful in knowing how to route th new belt...
http://www.gates.com/common/part_locator/view_diagram.cfm?id=S4003

Next, here's a link to a good video on how to replace a serpentine belt...
http://www.wonderhowto.com/how-to/video/how-to-inspect-and-replace-your-car-s-serpentine-belt-267229/

2.0L Engines
See Figures 11, 12 and 13
The accessory drive belt for 2.0L engines has no provision for manual belt adjustment, since these engines use an automatic belt tensioner. Drive belt slack is taken up by the automatic tensioner.
Movement of the automatic tensioner assembly during engine operation is not a sign of a malfunctioning tensioner. This movement is the tensioner self-adjusting and is required to maintain constant belt tension.
The belt tensioner has a belt length indicator. If the indicator marks are not between the MIN and MAX marks, the belt must be replaced.
Fig. 11: Drive belt routing-2.0L SOHC engine with A/C Fig. 12: Drive belt routing-2.0L SOHC engine without A/C Fig. 13: Drive belt routing-2.0L DOHC engine