Check engine light indicates problem with secondary air injection system 2001 saturn SL1

fix the reported code fault sensors then reset the ECM using a scan tool
turning off lights does not fix problems

P0410 Secondary Air injection System Troubleshooting ...

? 4:23
www.youtube.com/watch?v=dIrmkxj6wJE
Oct 3, 2008 - Uploaded by richpin06a P0410 Secondary Air injection System. ... I have a 2001 Saturn S-series showing this code. The air pump was not running. ... The fix for me was to replace the hose/wire that runs from the diverter valve, over a crevice on the ...

here is what i found on p1416.



P1416 Chevrolet
P1416 Chevrolet - Secondary Air Injection System Bank 2
Possible causes
- Faulty Secondary Air Injection (AIR) pump
- Secondary Air Injection check valve bank 2
- Secondary Air Injection (AIR) pump electrical circuit fault
- Blocked Secondary Air Injection (AIR) system

When is the code detected?

The P1416 code is set when no O2 sensor voltage change is detected by the Engine Control Module (ECM).


Possible symptoms
- Engine Light ON (or Service Engine Soon Warning Light)


P1416 Chevrolet Description
An Secondary Air Injection (AIR) pump is used on this vehicle to lower tail pipe emissions on start-up. The PCM supplies a ground to the AIR pump relay, which energizes the AIR pump. The Powertrain Control Module (PCM) monitors the HO2S voltages to diagnose the AIR system. During the AIR test the PCM activates the AIR pump during closed loop operation. When the AIR is activated, the PCM monitors the HO2S voltages and short term fuel trim values for both banks of the engine. If the AIR system is operating properly, the HO2S voltages should go low and the short term fuel trim should go high.

P0491 Secondary Air Injection System (Bank 1)
P0492 Secondary Air Injection System (Bank 2)
Good luck for you!
OBD2 code reader

Diagnostic Test Code (DTC) P0410 indicates that your secondary air injection system is not functioning properly.
Not all 2001 Chevrolet Bazers are equipped with secondary air injection. The secondary air injection system was added to vehicles that were to be sold in certain areas where the emissions laws required it, like the State Of California.

The Powertrain Control Module (PCM) monitors the system by commanding the secondary air blower motor to run and the air injection solenoid to open. This causes additional oxygen to enter the exhaust system. The PCM then monitors the signal from the oxygen sensors to see if the commanded air has in fact, entered the exhaust system. Code P0410 sets when the PCM has commanded the blower motor on and the solenoid open and there is little or no change in the oxygen sensor signal.

GM has had some problems with these systems and there has been a Technical Service Bulletin (TSB) issued that addresses some of the known concers. Below is a brief description of the TSB and the issues involved.

Bulletin No.: 04-06-04-015A
Date: November 28, 2006
TECHNICAL
Subject:
LN2, L43 or L35 Engine SES/MIL Light Illuminated, AIR Pump Ingesting Water and DTC P0410 Set (Replace AIR Pump and Inlet Hose Assembly)
Models:
1999-2003 Chevrolet Blazer, S10
1999-2001 GMC Jimmy
1999-2003 GMC Sonoma
1999-2001 Oldsmobile Bravada
with Vortec 2.2L I4 or 4.3L V6 Engine (VINs 4, 5, W - RPOs LN2, L43, L35)
Condition
Some customers may comment on the SES/MIL light being illuminated. Upon investigation, the technician may find a DTC P0410 indicating that there is a concern in the secondary air injection system.
Cause
Water may have collected in the AIR pump or the vent solenoid and frozen or corroded the pump.
Correction
Replace the AIR pump and install a new inlet hose and solenoid tube assembly...

The bulletin goes on and gives detailed information on how to perform the repair and the part numbers of the replacement parts needed to do so. Your local dealer can provide the parts for you and you can probably get them to print out a complete copy of the bulletin for you. It is not really hard to do if you want to do this yourself.

That's s failure of the secondary air pump. It'll have to be changed. It's an emissions component meant to help with cold start emissions. It won't cause engine running trouble but at inspection time you'll fail for smog. Change it before then and you'll be fine.

Does anybody know what secondary air injection system look like

With regards to the secondary Air Injection system, this is basically an inspect and replace broken hose detail.
Leave the inlet hose disconnected and start the engine. Listen and feel for exhaust hissing at the check valves.The check valve(s) will make like a gurgling sound as air is drawn in However , if exhaust is felt or heard replace the valve. Get a scanner and turn off the check engine light. Hope this works out for ya.

that code indicates a problem w/ the air injection system, a part of the emissions system. you should check the air pump, solenoid, check valves and vacuum hoses of that system. the emissions sticker under the hood should give you a detailed enough diagram of where the components are