Question about 1998 Mitsubishi Eclipse

1 Answer

On my car the motor mount bults are to long and i cant remove them i tried to jack up the motor but it dosent go up far enough and the same going down i need to change the timeing belt, water pump, and water pump puly and the bults are what is stoping me. and the crank puly wont come off is there a lock pin or something like that?

Posted by on

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    MVP:

    An expert that gotĀ 5 achievements.

    Governor:

    An expert whose answer gotĀ voted for 20 times.

    Hot-Shot:

    An expert who has answered 20 questions.

  • Contributor
  • 27 Answers

On the motor mounts on the driver and the passenger side there are 3 to 4 bolts that the motor mounts bolt to the tranny and to the motor. you can remove those leaving the motor mount still attached to the car

Posted on Oct 08, 2009

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Pulley not coming off


Depending on the Vehicle, You may have to put a Jack under the Oil Pan with something to distribute the weight and to protect the Oil Pan and then what you need to do is this...

Jack up the motor, remove the Upper Motor Mount and now you can lower the engine far enough to get the Pulley out of Most cars... I know this works on Honda, Hyundai and Toyota's without any issue. Just be smart to not just drop the front of the Motor and tax the Transaxle/CV Joints...

Good Luck

Apr 05, 2013 | Cars & Trucks

1 Answer

Cant get the oil pan off a 302


You have to jack the engine up after removing the motor mount bolts on each side. Then once you have the engine jacked up a few inches, slide a piece of wood (2x4) in between the upper and lower parts of the motor mounts on each side. This will keep the engine elevated enough for you to drop the oil pan and replace the gasket. Then, just put all the bolts back in in the proper torque sequence, torque them all to spec,remove the wooden blocks from the motor mounts, slowly lower the engine back down and put the motor mount bolts back in.

Mar 16, 2011 | 1993 Ford F150 SuperCab

1 Answer

Is there any way to replace the serpentine belt on a 97 oldsmobile achieva without removing the engine mount


If its the 3.1 liter with the upper engine mount on the passenger side of the motor than no. You will need to remove the mount.

The good news is is its not that hard to do. Place a jack under the oil pan with a block of would between the jack and the oil pan and the trans pan as far to the passenger side as you can and still be able to touch both pans with the block of wood.

Jack up the motor just enough so that it just start to push up on the motor mount. Remove the bolts that hold it to the bracket on the engine. Remove the retainer for the cruise, if equipped, unplug the cruise and set aside. Remove the nut from the mount on top and the two bolts from inner fender.

Jack up the motor just enough to remove the mount.

You'll then be able to replace the belt.

Dec 15, 2010 | Oldsmobile Achieva Cars & Trucks

1 Answer

What problems exist to change the oil pan gasket in a 1988 Cadilac Deville?


the cross member blocks access to the pan so u cant drop it to replace the gasket if u undo motor mounts and and tranny mount may jack engine far enough to drop pan to replace gasket

Jun 01, 2010 | 1988 Cadillac Sedan DeVille

1 Answer

How do i lift the engine soas to change motor mounts


Usually the best way is to use a jack with a piece of wood under the oil pan. You should be able to jack up the motor far enough to remove the mounts. Or a engine hoist (cherry picker) can be used.

Apr 28, 2010 | 1988 Cadillac Sedan DeVille

1 Answer

How do you remove the oil pan on 2001 grand prix


Remove the motor mount bolts on both sides. Using a jack & wood block, jack the engine high enough to allow the pan clearance enough for removal. Use wood blocks(4 by 4) at motor mounts & lower engine mounts onto the blocks. Lower & remove jack & block at jack. Remove pan bolts & carefully using a large pry bar or common screwdriver pry the pan away from engine . Good luck!

Apr 01, 2010 | 2001 Pontiac Grand Prix

1 Answer

My rear motor mount on 98 Taurus needs to be repaired looking for step by step instructions


1. need ramps
2. Floor jack and a block of wood to jack motor up after unbolting mount.
3. Unbolt mount. Jack up the side of the motor that you want to remove the mount. Just high enough to get it out and in. The motor will raise high enough.
4. Remove it and replace it with the new one.

I had to replace the same one on a car that I worked on kinda pain in the ****.

Feb 11, 2010 | 1998 Ford Taurus

1 Answer

Need to replace motor mounts


jack up and support car in the front with jack stands. Then use the trolley jack with a two by four to support the motor under the oil pan jack up the engine only about an inch after loosening mount bolts or enough to attain enough clearance to remove old mount, but not too high, you may want o remove the other mounts located (if any on the top side of motor) referring to a haynes repair manual is always a good idea certain precautions may be neccessary.

Jul 02, 2009 | 1999 Mercury Villager

1 Answer

I cannot remove the long bolt from alternator.


how about releasing the upper motor mount and carefully jack the engine up enough to remove bolt??

Dec 11, 2008 | 1993 Ford Probe

1 Answer

Trying to drop the oil pan out of my 1994 Ford F-150 (4.9L) to replace the gasket. Ive taken out the motor mounts and jacked the engine almost high enough to get the oil pan out and I am wondering if i...


done this on several i-6 f-150s. slide back or remove transmission, remove motor mount bolts from frame(not motor), jack motor up as far as possible without damaging egr valve or wiper motor when they hit, shim under motor mounts so that when you drop the jack the motor does not come back down any(the motor is well balanced on the mounts, it will not fall out of the truck like a v8 will), then remove the oil pan. you May have to remove the pickup tube(usually not), and you May have to rotate the crankshaft so that the lobes clear the oil pan. this is a common problem with these trucks due to the size of the oil pan(Huge), and the minimum pan to crossmember clearance

Jul 19, 2008 | Ford F-150 Cars & Trucks

Not finding what you are looking for?
1998 Mitsubishi Eclipse Logo

153 people viewed this question

Ask a Question

Usually answered in minutes!

Top Mitsubishi Experts

yadayada
yadayada

Level 3 Expert

75807 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22133 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8172 Answers

Are you a Mitsubishi Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...