Question about 1995 Lincoln Town Car

1 Answer

The driver side window goes down with the switch but will not go up and i had to manually pull it up. Then slowly the window started to slide down on its own about have way. I will place a small screwdriver in the jam until i find out what the problem is the motor appears to be working so it could be the plastic clip the the window slides up and down on help me please trying to save money, and not get ripped off.

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Brigadier General:

    An expert that has over 10,000 points.

  • Master
  • 3,533 Answers

I have a 93-lincoln town car one of the probelm was it had a bad motor and the other thing it was the window regulartor itself take the panel off and make sure there is some kind of lube on the tracks ask someone at the part store what to buy if you stop by your local lincoln dealership they will print you out a diagram for free showing you how it look inside wish you the best of luck Michigan Man.

Posted on Oct 08, 2009

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How to replace low beam bulb on toyota avalon XL 2009


Here's what I did to change the driver's side halogen low beam bulb #9006. Do so at your own risk.


1. First ensure fuses are OK. There are four(4) 15A fuses in the fuse box under the hood - drivers side. All are clearly mapped out on underside of fuse box cover. I used the continuity tester circuit on a VOM to ensure they were OK.

2. Remove large plastic shroud that runs across from one side of the top front under the hood of vehicle to the other side. 5 plastic pins held mine in place. Once off -- you'll be able to see your vehicles radiator cap. Removing this helps provide some additional access and leverage to better work with.

3. Remove battery negative cable - 10mm socket

4. Remove battery hold down bracket - rod - one(1) 10mm bolt at front - one(1) 10mm nut on rod. Deep socket 10mm helps with the 10mm nut.

5. Remove battery positive cable - 10mm socket

6. Remove battery and plastic battery tray

7. You should see the halogen low beam bulb #9006 in front of the fuse box(drivers side). Mine has a brown electrical plug connected to it. It helps to first remove and place out of the way - the parking light which is just to the left - the assembly for mine is light gray in color. Doing so gets that wire out of the way. One less distraction when you reach in to remove the low beam halogen bulb #9006.

8. Remove electrical connection from halogen low beam bulb #9006. There's a locking tab on the bottom - press in and while doing that - push down on the electrical connector from the top. It comes off without a great deal of effort.

9. Remove halogen low beam bulb #9006 by turning counter-clockwise - looking at the bulb from the back. Mine did not want to twist loose right away. Go slowly - take your time. It should eventually come loose. #9006 bulb came out easily even with the fuse box nearby.

10. Install new halogen low beam bulb #9006. I opted for a $10 Wal-Mart Sylvania #9006.

11. Reconnect electrical connection to the new halogen low beam bulb #9006.

12. Clean battery tray and terminals on battery + connections on battery cables.

13. Install battery tray and battery

14. Connect positive battery cable to battery - 10mm

15. Connect hold-down and rod + one(1) 10mm bolt at front and one(1) 10mm nut that goes on rod at rear.

16. Connect negative battery terminal - BUT - before doing so - have your remote locking/unlocking device handy. As soon as you connect the negative battery cable to the batteries negative terminal - the horn will sound(alarm). Quickly depress the UNLOCK button on your vehicles remote. Finish tightening the negative cable. You should also see that the low beam is once again functional as it will come on when the alarm is sounded.

17. Reinstall large plastic shroud and all lock down tabs

18. Start car and set clock/radio settings/etc.

19. There is a procedure to resync the power windows. The following provided by inov8 from another forum.

Copied from TSB PD002-05

NOTE:
Anytime the battery terminal has been disconnected, please initialize the driver's door
power
window and front passenger's door power window after reconnecting the
battery terminal.

With ignition switch in the "ON" position, do the following:

1. Push down and hold the driver's door power
window switch to completely open
the
window.
2. Pull and hold up the driver's door power
window switch until the window closes.
Continue holding the switch for approximately one second until the switch changes
from blinking to a constant illumination.
3. Check for proper operation of the "one-touch open and close" function by fully
pushing the switch briefly to the "DOWN" and "UP" positions.

At this time the power
window switch for the passenger's door window should
be blinking.
4. Push down and hold the passenger's door power
window switch to completely open
the
window.
5. Pull and hold up the passenger's door power
window switch until the window closes.
Continue holding the switch for approximately one second until the switch changes
from blinking to a constant illumination.
6. Check for proper operation of the "one-touch open and close" function by fully
pushing the switch briefly to the "DOWN" and "UP" positions.

Sunroof initialization is similar.


20. There is a procedure to resync power seats. Extracted from factory service doc:

Using seat switches - fully slide seat fwd. - fully recline seatback fwd. - fully raise seat cushion and head rest.

Using seat switches - fully slide the seat rearward - fully recline the seatback rearward - fully lower seat cushion and head rest.

Jun 14, 2012 | 2009 Toyota Avalon XL

1 Answer

Changing the window motor driver side


Hello,

To change the window motor driver side, follow the steps below:
  1. remove 1 visible bolt left side of arm rest
  2. Pop out window switch/door lock/ mirror adjustment control panel with a screwdriver
  3. Use panel remover or just pull on interior panel to remove must slide it off of door handle
  4. Slide control switch panel down through hole you popped it out of
  5. Pull vapor barrier loose bottom right side to expose coiled spring and window motor
  6. Tape window in the up position using masking or package tape
  7. Mark a straight line across coil spring to make sure you can realign it when reinstall
  8. Use tool j-38864 connect it near outer part of coil sprint where it hooks to retainer or in a pinch use pointed vice grips at same location ensuring they are firmly locked on spring ( be very careful, I'm not responsible for any injury if you are not)
  9. Force spring clockwise to disengage it from it's retainer point
  10. Pull spring slightly outward just enough to clear the retainer point and slowly let it uncoil counterclockwise and let it sit there
  11. Disconnect wire connector from right end of window motor
  12. Use your hands and push 3 plastic retainer points outward as you lift up on window motor to disengage from retainers careful not to break the plastic retainers comes out pretty easy
  13. Install new motor into the plastic retainers, make sure filly seated ( lining up plastic Guides into holes in motor (3 points)
  14. Reconnect wire connector to new motor
  15. Use J38864 or vice grips to recoil spring, resit it to retainer point as before you have to be very careful in order not to hurt yourself
  16. Remove tape from window and test up/down switch ( key must be on)
  17. Reseal vapor barrier in place as it was prior to starting
  18. Slide switch control back up through hole in door panel from where it mounts
  19. Slide door over door handle
  20. Align retaining clips to holes and push them home with gentle raps of your hand start at the top and work downward on panel
  21. Replace both bolts in arm rest
  22. Pop window/door lock control panel back in place
That is how to change the window motor of the drivers side of a 2000 pontiac montana.

Take care and good luck

Jan 06, 2011 | 2000 Pontiac Montana

2 Answers

The passenger power window will not go up or down,driver side works.


replace the window motor r ck to see if the window is still on track

Aug 28, 2009 | 1994 Chevrolet Astro

3 Answers

Pontiac Grand Prix Drivers side window won't go down


take the door panel off and see if your regulator is not stripped it is a cable regulator so the wire will be hanging if not try directly operating the motor at the motor and see if it moves up and down fairly easy and fast like new. if it does the problem is in the switch and will need to be replaced. the plug on the motor is a two wire plug and can be hooked up in either direction to make window go up and down.

Aug 28, 2009 | 1997 Pontiac Grand Prix

2 Answers

VW Beetle the drivers side window goes half way up but stops


sounds like you have a bad regulator. this is caused by the cables in the regulator becomming dry and start to bind up and then break causing the window to free fall down.

Jul 15, 2009 | 2000 Volkswagen Beetle

1 Answer

2000 rodeo drivers side electric window goes up but not down?


pull the control switch out n clean contacts or try and spay contact cleaner on them

Jun 13, 2009 | 2001 Isuzu Rodeo

2 Answers

Passenger side window dont go fully up


Hi.
Sounds like the "anti-pinch" mechanism is coming into action on the drivers side.
If the window encounters any resistance when closing it will stop.
Check the window seal for damage and correct fitment, make sure there is nothing obstructing the glass. If you are OK with the seal and channels at either side and the window is going up an down "square", try some lubricant in the channels either side with the window in the down position and operate a few times.

Passenger side. The motor for the window must have been disconnected from battery voltage at some time and it has lost its reference points. That is, where to start and stop.
Nudge the window near to the top, but not closed, then close the window holding the switch down for at least 5 seconds. Then open the window and hold the switch down as before.
You may have to do this more than once.

There should be a section in your owners manual covering this procedure.

I don't think the two problems are connected physically.

May 17, 2009 | Peugeot 604 Cars & Trucks

1 Answer

Power window problems!!!!! window stuck down and it looks like


use the switch from the other side connect just use it and unplug it..it the switch does not work go to motor

May 08, 2009 | 1999 Chevrolet Camaro

1 Answer

Driver side door window slowly fell down into the door of my 1997 dodge dakota. The glass did not break.


Power or crank? Either case the rails that hold the window on probably broke. there are slides inside the door that keep the window in place, if a slide broke, or if one of the brackets broke, the window will come down. I cant really recomend doing this yourself as ive had the same issue on other vehicles and pulling apart the door and messing with the slides and stuff in there is a real pain. Hopefully it only fell off the track and you can put it back in place. If not, if your not very handly i would suggest taking to someone.

Dec 03, 2008 | 1997 Dodge Dakota

Not finding what you are looking for?
1995 Lincoln Town Car Logo

195 people viewed this question

Ask a Question

Usually answered in minutes!

Top Lincoln Experts

yadayada
yadayada

Level 3 Expert

74945 Answers

fordexpert

Level 3 Expert

5467 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Are you a Lincoln Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...