Question about 1999 Ford F250 Regular Cab

1 Answer

BRAKE PAD MELTED TO ROTOR

FRONT BRAKE PAD MELTED TO ROTOR

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Master
  • 454 Answers

Replace front rotors and pads.

Posted on Oct 08, 2009

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Hi I have a peugeot 406, I HAVE REPLACE THE FRONT BREAK DISC AND THE BREAK PADS BUT IT STILL GIVE THAT HORABLE NOIOSE WHEN I BREAK. Its realy iritating and i take good care of my car,


Remove the brake pads from the car and smear small amount of high melting point silicone grease e.g. Carlube, at the back of the brake pads. Be careful do not put on too much and never has it touch the pad material and the disc rotor. if you do, remove it with brake clearner immediately. The squeaks noise shall disappear if you fix it properly.

Sep 07, 2013 | 1999 Peugeot 406

2 Answers

My brakes sound like they are grinding


check rear rotors and front rotors for rust buildup (flahlight helps). does the vehicle shake when you come to a hard stop? You will either need to have a front or rear or both brake job (rotors cut or replaced and new brake pads) If the vehicle is shaking when coming to a stop, its probably your front pads. If your hearing the noise from the rear its the rear pads or it you hear it from the front its the front pads. If there significant rust build up or your pads are low a brake job is recommended.

May 04, 2011 | 2008 Nissan Armada

4 Answers

Steering wheel shakes at high speed when brakes are applied


This is caused by the front disk brake rotors being warped from heat and running out of true, the wobble of the warped rotors causes the wheel to shake when you apply the brakes, it is worse the higher the speed you apply them at. Have the front rotors machined flat again or just replace them.

Mar 16, 2011 | 1998 Toyota Camry

5 Answers

When i press on brakes i can hear a grinding noise coming from he front end, what could it be?


Brake pads are worn. That noise is the sound of the backing plate for the brake pads hitting the rotors. You will need to replace the pads and probablt the rotors. When the brakes go metal to metal like that it typically destroys the rotor.

Feb 21, 2011 | 1997 Jeep Grand Cherokee

1 Answer

How can I change the rotors and brakes on a 2006 Cadillac?


Front brake
Step 1: Identify Front Disc Brake Components
brake_pads_rotor.jpg
Front Wheel Drive Brake Assembly
Most front disc brake components include: brake rotor, brake pads, brake caliper, caliper mount and brake flex hose. Brake service usual occurs between 20,000 and 40,000 miles depending on driver habits, road conditions and brake pad/ rotor materials used.
Step 2: Remove Brake Caliper to Replace Pads
brake_pad_set.jpg
Removing Brake Caliper Mounting Bolts
Locate primary caliper mounting bolts; apply wrench pressure counter-clockwise (When looking at the head of the bolt) to remove the bolts, upper and lower. Make sure the bolt threads are in good shape and replace if necessary.
Step 3: Remove Front Brake Caliper
remove_brake_caliper.jpg
Remove Front Brake Caliper
After removing the primary caliper mounting bolts lift the brake caliper off of the rotor and then tie or secure to the side, being careful not to bend or kink the brake caliper flex hose. Thoroughly inspect brake caliper and brake hoses for leakage, cracks or chaffing and replace as needed. Next remove the brake pads (If not mounted in the caliper) and secondary caliper mounting bolts. Notice how great protective gloves work, most technicians use them on the job today.
Step 4: Remove Brake Pads
remove_brake_pads.jpg
Remove Front Brake Pads
Once the brake pads have been removed, make sure if there is anti rattle hardware to transfer to the new brake pads. Some brake pad manufacturers will include the proper lube (Caliper slides) and anti-rattle hardware to ensure proper performance of their product.
Step 5: Remove Caliper Mount
remove_brake_pads_holder.jpg
Remove Caliper Mount Bracket
Finish removing secondary caliper mount bolts and remove caliper mount. Note: clean and lube caliper slides and pad friction surfaces of all foreign material or build-up.
Step 6: Remove Brake Rotor
brake_rotor.jpg
Remove Brake Rotor
With the caliper mount out of the way you can now remove the brake rotor. Sometimes it can get stuck so you may need to tap it with a hammer or use penetrating oil to free it up. Some manufacturers use small screws to hold the rotor on as well. Clean and inspect wheel studs, replace if any are damaged. Also clean bearing hub rotor mount surface to ensure the proper mounting of the new brake rotor. Inspect the ABS sensor wheel for cracks or damage and replace as needed.
Step 7: Depressing the Brake Caliper
compress_caliper.jpg
Resetting Brake Caliper
To install the new brake pads you must retract the brake caliper piston. Remove the master cylinder lid or open the brake caliper bleeder screw to allow excess brake fluid to be released if necessary. Install C clamp tool and gently tighten clamp until caliper piston is fully depressed. Note: use old brake pad to protect the caliper piston. Close the bleeders once the piston is retracted completely
Step 8: Installing New Brake Rotor
new_brake_rotor.jpg
Install Brake Rotor
Install new brake rotor, the new rotor is manufactured with a protective film over the rotor to keep it from rusting, remove protective film with brake cleaner before installing; also after the brake job is complete you may experience a small amount of smoke from the rotor when first used. This is normal and will go away after the first couple of uses.
Step 9: Installing New Front Brake Pads
new_brake_pads.jpg
Installing New Brake Pads
Reinstall the front brake caliper mount, and then install front brake pads. Make sure the pads are seated properly in the caliper mount; it must be a close fit to work properly..
Step 10: Reinstall Front Brake Caliper
front_brake_rotor_pads.jpg
Re-Install front Bake Caliper
Reinstall front brake caliper and reinstall caliper-mounting bolts, recheck all mounts and mounting bolts. Check the caliper slides to be sure there is no bind and that the caliper moves freely back and forth on the caliper slides. Bleed brake system per manufacturer's specifications to relieve any air trapped in the system. Before driving the vehicle, push the brake pedal down and let it up slowly, repeat until normal brake pedal operation resumes, this operation is forcing the brake pads to travel to the brake rotors.

Dec 18, 2010 | 2006 Cadillac STS

2 Answers

Front end shakes when braking


will try to help. when front wheels shake while applying brakes and you can feel shake in steering wheel, front brakes and rotors need replacement.rotors are warped,if you replace front brake pads, it will return[shaking when you apply brakes] suggest that you replace front rotors[both] replace [both]front brake pads. cost? i would charge [brake pads cost $55.00] labor,$60.00] total $115.00 thank you for choosing fixya.com

Dec 04, 2010 | 1998 Ford Windstar

1 Answer

Rumbul nnoise in front when brakes are appled


The brake pad is worn down to the rivet that holds the pad to the base.
The metal rivets are in contact with the metal brake rotor.
Metal-against-metal...
Replace both front brake pads and at least one rotor.
You should be able to see both front rotors w/o removing the wheels.
The rotor with rings like Saturn (the planet) is the one to replace.

Replace soon before the other rotor meets the same fate.

Hope this helps!

Sep 11, 2009 | 2000 Pontiac Grand Prix

3 Answers

In 2004 Impala, do I have rotor or drums?


The best way to answer you question is to tell you to take the vehicle to your nearest dealer and inquire with the parts dept. I can tell you that on the ffront of your car you have rotors and the brake used on the front is called a pad. Also your vehicle does not have a separate parking brake. It is the same as the regular rear brake no matter which type of brakes you have on the back.

Jul 02, 2009 | 2004 Chevrolet Impala

Not finding what you are looking for?
1999 Ford F250 Regular Cab Logo

Related Topics:

89 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

76846 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22246 Answers

fordexpert

Level 3 Expert

5546 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...