Question about 1992 Chevrolet Camaro

1 Answer

Hello I blew the crank fuse is it possiable that I blew another cause car wont start.

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Master
  • 3,741 Answers

Yes quite possible you may have blown another fuse too--- if the wiring's are grounded somewhere get it checked.and yes the car wont start until you change the fuse.also check that the fuse insertion socket is not rusted.if its rusted just clean it properly before putting in new fuse.

thanks,keep updated and please rate the solution positively.

Posted on Oct 08, 2009

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

If my chevy tracker 2004 cranks good but wont start , which relay do you think I need to change.. is it the crank relay? or fuel pump relay?


I don't know what kind of damage you may have done? Can you communicate with computer, check applicable trouble codes, anything? If you can't communicate with computer, start, there.
You can check the basics, if you haven't already. With engine cranking check for spark at the spark plugs. If spark everywhere, use a gage and check proper fuel pressure.

Dec 01, 2016 | Cars & Trucks

1 Answer

Starter wont crank and fuse blew and put new fuse and keep blew out what cause fuse blew


starter is probably stuck take starter out and see if you can rotate the shaft .if not replace starter.

Sep 09, 2014 | Cars & Trucks

1 Answer

Installed radio now car wont start


wont crank, you failed to remove battery lug minus during service
and blew some fuses (hope, it did, other wise, boom)

Nov 08, 2013 | 1997 Acura CL

1 Answer

Crank turns, fuel flowing through rubber lines. wont fire at all, did blow glow plug fuse when driving along, would fire up and then stall, now wont fire at all with fuse rplaced.


if the fuse blew to the heaters then its obvious the wire from the relay box to the heaters is shorting somewhere along the line or one of the heaters itself has burnt out on the end causing this short .

Dec 01, 2010 | 2001 Isuzu Trooper

1 Answer

My 2005 g6 gt wont start it has nothing no clicks no lights nothing . tryed boosting it stills nothing


check ur cranking fuse block probably blew,check ur main fuse in ur fuse box

Mar 07, 2010 | 2005 Pontiac G6

1 Answer

2008 corvette engine wont crank


Hello there:
if every thing was ok befor the dash issue / air bag than i would go back and check to see if there was any wires that were possiably cut or ground out or pinched got dissconnected. under the dash or in the engine compartment or a fuse might have gotten removed or blew. during reassembly
If you know someone that has the handheld diagnostic unit i would have them do a scan on the vehical and see if any codes pop up this will help you determine exactly what is wrong also ok?
I hope that his has been very helpfull for you
best regards michael

Oct 28, 2009 | 2008 Chevrolet Corvette

2 Answers

My car cranks but dont start


you need to make sure its gettin spark and fuel and compression start from thare also plug a scan tool into it so see if all the sensors are working possibley ecu could be fried

Jun 01, 2009 | 1997 Honda Civic

1 Answer

Blows fuse wont start


More than likely its being caused by a short-circuit to ground in the wiring in your Cranking Circuit.

If it blows the fuse immediately after installing the fuse, its probably a hot-wire. If it blows it the second you try to crank it over, its probably one of the wires between your ignition and the Starter Relay.

To track down the bad wire you'll need a Wiring Schematic for the vehicle and either a Digital Volt/Ohm-Meter or Test-Light and a basic understanding of wiring which is... honestly a little hard to explain over the internet. However, that is the only course that can be taken without taking the vehicle to a qualified Dealership Technician.

May 16, 2008 | 2001 Ford Expedition

Not finding what you are looking for?
1992 Chevrolet Camaro Logo

Related Topics:

56 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts

yadayada
yadayada

Level 3 Expert

76846 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22246 Answers

Ronny Bennett Sr.
Ronny Bennett Sr.

Level 3 Expert

6927 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...