Question about 2001 Mercury Villager

Open Question

Replacing door handle on pasenger side sliding door on villager van, does small panal come off? or must i remove whole door panal?

Posted by on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad
  • 1 Answer

SOURCE: outside sliding door handle?

Yes. It is a difficult job, but not impossible. The hardest part is actually removing the interior door handle. Here are the steps.

  1. remove the interior door handle by pressing the door panel in and prying out the C-ring retainer clip
  2. remove the lock slide switch bezel with 1 screw, then insert a blade on the bottom left of the slider between the slider and bezel, and release the clip, the slide the bezel toward the rear of the vehicle and pull out
  3. carefully unclip the door panel around the lower edge and sides and lift the door panel UP and off
  4. remove the interior lock slide switch with 2 screws
  5. pull back the plastic vapor shield part way to expose the mechanism
  6. there is a cable that runs from the mechanism to the exterior handle, unclip it from the door frame
  7. there is a rod that drops down from the door handle to the mechanism, release the rod from the plastic clip
  8. locate a large (likely black phillips) screw next to the door handle on the EDGE of the door, remove it
  9. locate a 10mm screw on the inside behind the door handle, remove it
  10. locate the final 10mm screw behind the handle through an access hole, remove it (careful not to let it fall inside the door)
  11. the door handle will push out through the door part way- there is another C-clip securing the lock cylinder that will need to be removed, and the lock cylinder can be pushed into the door cavity
  12. pull the door handle through the outside of the door skin- the door handle assembly is still attached inside the door by the latch cable- the cable can be easily removed from the handle assembly to remove it completely
  13. you will likely find that the end of the door handle itself is broken off- don’t buy a new handle! Email me and I will show you my free and possibly better solution that will likely last the life of the vehicle dbonnell1972 at yahoo dot com
re-assembly is the reverse of the removal

Posted on Sep 01, 2008

Ad
  • 1861 Answers

SOURCE: The sliding door handles of my 1998 Toyota Sienna have both broken.

OK, here you go:

Pry out on the bottom of the cupholder bottom, relieve 2 clips, pull the bottom out & slide it down

Remove the door trim screw, and pry out on the door panel, relieve 10 clips, pull door trim off

Remove the horizontal upper trim cover at the top of the door; relieve 4 clips

Remove the vertical door trim cover; relieve 2 clips

Remove the window garnish around the handle; pull the small trim cover off; remove 3 screws
This exposes the inside handle

The inside handle is retained by 2 screws.

Posted on Sep 27, 2008

  • 341 Answers

SOURCE: Replacing exterior door handles 1998 Safari van

remove door panel.. inside door you will see a rod going to the handle..on the end is a clip ..push the clip up off the rod .slide the rod out..remove 2 ..13mm nuts from handle ..remove handle

Posted on Nov 14, 2008

  • 65 Answers

SOURCE: 2004 toyota sienna sliding door locking trouble

Sounds like something isn't right.Try to disconnect the battery for a few minutes and see if that helps.Some times the ecu gets haywired and disconnecting the battery might reset it.And if it is the original battery you might want to get it tested.

Posted on Dec 04, 2008

  • 72 Answers

SOURCE: 99 mercury villager van

Yes, but you need lots of skill and body tools to permanantly repair that. This is caused by owners not knowing that there are tiny drain holes in the bottom of the doors, that get clogged up with dirt. If a person just checked and cleaned them out once a year, with a pipe cleaner.......this would never have happened

Posted on May 28, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

1999 Chevrolet Silverado power windows, How do you remove drivers side door panel


not really sure on that one but on most first you will need to remove screw around handle that opens the door that needs to be removed. also should be screws underneth handle that pulls door shut that you will have to remove and in some cases . check around edge of door panal for more screws and if found remove them also. once all screws are removed you will need to pry on door panal slightly because there are clips behind panal holding it on. in alot of cases the clips break when removing panal but dont worry the can be bought at your local auto parts store and are very easy to replace. I usually use something flat like a small stiff putty knife to help pry door panal lose. this helps insure that you dont break of crack the panal. after all clips are off simply unplug wire connections and door handle linkage and your done. .....hope this helps and good luck

Aug 13, 2012 | 1999 Chevrolet Silverado 1500

1 Answer

1997 mercury villager passenger side mirror replacement guide. how do i do it? is there an easy access panel or does the whole door panel need to be removed


door panel must come off.

go here for villager help

http://groups.yahoo.com/group/villagerquest/

Section 01-05: Trim, Interior 1997 Villager Workshop Manual
REMOVAL AND INSTALLATION Trim Panel(s), Door
Front
Removal
  1. Disconnect the battery ground cable (14301) if equipped with power locks or power windows.
  1. svv~us~en~file=ani_caut.gif~gen~ref.gif CAUTION: Use care when removing the front door inside handle escutcheon (22620). Failure to do so can result in damage to the component.
    Carefully pry off the front door inside handle escutcheon by inserting a standard 1/4 inch screwdriver between the top rear portion of the front door inside handle escutcheon and the front door trim panel (23942).




  1. If equipped with manual windows, slip a clean shop rag between the window regulator handle (23342) and the front door trim panel.
  1. Pull the shop rag back and forth to release the window regulator handle clip.




  1. Remove the three cover caps and front door trim panel screws.
  1. Remove the one front door trim panel capped screw from the door pull handle.
  1. If equipped with power windows, remove the door pull handle. Disconnect the electrical connectors.
  1. Slide a flat-bladed tool behind each of the retainers and twist the tool to disengage the front door trim panel from the front door (20124).
  1. Remove the front door trim panel.
Installation
To install, reverse the removal procedure. Body Side
Removal
  1. Gently pry loose the body side door latch handle bezel and remove it.
  1. Slide a suitable tool behind each of the retainers and twist the tool to disengage the body side door trim panel from the body side door (24622).




Installation
To install, reverse the removal procedure. Door Electrical Connections
Removal and Installation
Refer to Section 01-11 for Power Window, Section 01-09 for Power Mirror, or Section 01-14B for Power Locks. Watershield
Removal
  1. Remove the Front Door Trim Panel . Refer to the removal procedure in this section.
  1. Remove the front door watershield by carefully detaching it from the adhesive.
Installation
  1. Install the front door watershield in the proper position and press firmly at the adhesive areas. If necessary, use additional adhesive to ensure an adequate seal.
  1. Install the Front Door Trim Panel . Refer to the installation procedure in this section.

May 22, 2010 | 1998 Mercury Villager

1 Answer

How to remove door panel to get into to replace door latch, pasenger side?


I have your shop manual & wiring diagram book for $25 plus $5 postage, but go here as well.

http://groups.yahoo.com/group/villagerquest/

There are a couple of covered screws to the fron of the panel and a screw in the door handle cup pocket and about 10 spring clips around the perimeter. The hardest part is getting the cup around the pull handle off. It has a couple of ridges at the top and bottom so it has to be pried out. Almost always a ridge breaks but it will still hold together.

Apr 21, 2010 | 1993 Mercury Villager

1 Answer

In my 96 mercury villager the auto locks r going crazy. the driver door wont stop locking on me. i would try to manually hold the unlock botton in & when i let go it just locks up the whole van...all...


http://autos.groups.yahoo.com/group/villagerquest/go here and read the files on this issue.You have water in the door lock actuator connector or you have a wire shorting out on the sharp inner door panel.Also, you can cut a wire that will stop this circuit from working because you don't need it anyway. In the links is the procedure.

Jun 03, 2009 | 1996 Mercury Villager

1 Answer

How to remove rear door panal for 03 cts


If you have power windows start by disconnecting your negative battery cable. Then you need to locate and remove the screws that hold your interior door handles in place (they may be hidden by snap in, or snap on clips). Once you remove the screws that hold the door handles, remove any wire connectors to the handles, if they're not power you will need a small hook (kinda like a knitting needle) to remove the window crank. A manual window crank is held in place by a clip on the base. Slide the hook behind the base and remove the clip. The door panel itself, is held on by snap in clips, and you will need a small pry bar to pull them from the door (try to get as close to, or directly under the clips to prevent them from tearing out of the door panel). Once the clips are removed from the door, pull the panel upward to remove it from the door.

Install in reverse.

I hope this helps you, and I wish you luck on your repair.

May 10, 2009 | Cadillac CTS Cars & Trucks

1 Answer

Handle broke off sliding door on drivers side 2000 mercury villag


Trim Panel —Sliding Door
Special Tool(s) syv~us~en~file=st1181a.gif~gen~ref.gif Safety Belt Bolt Bit (Used for T-50 Head Bolt)
501-010 (T77L-2100-A) Removal
  1. Remove the sliding door trim panel finish panel.
94d5982.gif
  1. Remove the sliding door trim panel.

Apr 13, 2009 | 2000 Mercury Villager

1 Answer

Broken door handle - 2001 Nissan Quest SE


first you van order parts at discount from tascafordparts.com.
quest & mecrury villager are the same vehicle made at the same assembly plant. good luck to all. If you were in detroit area, I wold help you.

Trim Panel —Sliding Door Removal
  1. Remove the sliding door trim panel finish panel.
532ac84.gif 2. Remove the sliding door trim panel 2965fbe.gif Latch Remote Control —Sliding Door Removal
  1. Remove the rear sliding door trim panel. For additional information, refer to Section 501-05 .
  1. Position the watershield aside.
  1. If equipped, disconnect the sliding door power door lock actuator electrical connector.
f373e91.gif
  1. NOTE: Mark the position of the sliding door rear latch cable adjusting bracket before removing the bolt.
  2. Disconnect the sliding door rear latch cable.
  3. Remove the bolt.
  4. Remove the sliding door rear latch cable adjusting bracket from the latch remote control.
  5. Disconnect the sliding door rear latch cable from the latch remote control.
b8f2f32.gif
  1. Remove the 4 sliding door front latch bolts.
NOTE: If necessary, transfer parts to the new sliding door latch remote control.
Remove the sliding door latch remote control.
  1. Remove the bolts.
  1. Remove the sliding door latch remote control.
cb5ee71.gif
Handle —Exterior, Sliding Door Removal
  1. Remove the sliding door latch remote control. For additional information, refer to Latch Remote Control—Sliding Door .
  1. Remove the sliding door exterior handle.
    1. Remove the nuts.
    1. Remove the sliding door exterior handle.
0c820f3.gif

Mar 08, 2009 | 2001 Nissan Quest

1 Answer

Replace pasenger side mirror


it looks like you have to remove the door panal and unbolt the mirror and dissconect it, it should be the same, on pretty much all cars you have to remove the door panal to get to the mirror and it looks like cadillac hasn't changed much on stuff like this, they just chaged the look and style of the door panal, hope this helps any should be an easy fix but take your time and be easy with it, stuff can brake,good luck on your cadi, hope this helps you out. 

Jan 05, 2009 | 1994 Cadillac DeVille

2 Answers

My back hatch door doen't want to open


You need to climb in the back and remove the plastic panel from the hatch to access the lock. There may be a small access door over the locking mechanism to help you avoid removing the whole thing. Could be dirty and sticky and fixable with a bit of graphite lube.

Nov 17, 2008 | 1996 Mercury Villager

Not finding what you are looking for?
2001 Mercury Villager Logo

Related Topics:

1,012 people viewed this question

Ask a Question

Usually answered in minutes!

Top Mercury Experts

yadayada
yadayada

Level 3 Expert

76164 Answers

fordexpert

Level 3 Expert

5522 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Are you a Mercury Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...