Question about 2001 Dodge Ram 1500 Truck 2WD

1 Answer

Whats the easiest way to get to my rodor button?

Posted by on

×

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Dodge Master
  • 2,002 Answers

Your rotorbutton is under the distributor cap and it needs to come off. You should see 2 screws on the side of the cap, use a screwdriver andpush down and turn them 1/4 turn, lift the cap. DON'T pull the wires off the cap unless you mark them so you can put them back in their exact location. DON'T turn the distributor unless you mark it's exact location with the motor. You may have to wiggle to get the cap off with the wires on but it will save you a lot of grief.
If you want to get to the rotor button to change it you should do the cap at the same time. In that case you can transfer the wires to make removal of the old cap easier BUT make sure you have the new cap lined up exactly in the same position as the old one before you do. Hope this helps.

Posted on Oct 09, 2009

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

My 1996 gmc pickup has new plugs and wire new gas cap new distbor cap n rodor the code is still misfire proventin me from getting my plates


check for leaks on all vacumn pipes and in line one-way valves and its known for positive crank ventilation (PCV) valves,solenoids and diaphrams to create rough running engine conditions when they collapse or malfunction

Mar 15, 2016 | GMC Cars & Trucks

1 Answer

2000 f150 4.2l v6 starting touble


Did they balance the new tyres ?. warped rotors can only be felt when the brakes are applied,you may have to have the injectors cleaned and flow tested.

Apr 07, 2017 | Ford F-150 Cars & Trucks

1 Answer

I also have a power window that will not go down on the passenger side. Is there a site I can go to that will show me how to take the door apart to check the wiring and/or motor.


Sometimes the boot coming out of the front of the door gets a wire broke in it you can just pull the boot out from the door or the door post and inspect for any broken wires if your on the fence about tearing the door apart that is the easiest but if the wires are good the door panel isnt hard to remove just note once all the screws are out the panel slides up to come off if you just pry it off it will break all the fingers that hold it to the door

Aug 10, 2012 | 2001 Ford Expedition

1 Answer

Hello, I have a 1992 Camaro RS 25th Anniversary ed. 3.1 V6. 118k miles. 700r4 Transmission. & My problem is.. I ran it low on gas, put gas in it.. ran like ****.. missing.. sputtering.. low power.....


CHECK FUEL pressure and take a fuel sample see if has water in it. since started problem rt after getting gas sounds lik you got some bad fuel

Jun 02, 2011 | 1992 Chevrolet Camaro

1 Answer

2005 4x4 chevy silverado, can't get rodor off, has an outer bearing off where axle goes through. should just slide off, can push shaft back in but can't get rodor off


Tap the rotor around with a hammer, sometimes where they connect they rust on there. Just make sure when doing it not to damage the rotor

May 28, 2011 | Chevrolet Silverado 1500 Cars & Trucks

1 Answer

My son lost the key to his 1991 Chevy Cavalier. What's the easiest and cheapest way to get his car going again?


Rip into the stearing column, remove both wires from ignition, put on a push button and use the button to start the car. Becomes easy to steal tho. Maybe hide the button

Mar 06, 2011 | 1991 Chevrolet Cavalier

1 Answer

Rear sliding doors are hard to open manually . does not open automaticlely. when I push the button, you hear a click sound, but nothing happens. what should I do ?


The easiest fix is to check the railing or any reason it may not be closing smoothly...there may be an obstruction or something protruding that keeps it from operating properly. Good Luck!!!

Sep 16, 2009 | 1999 Ford Windstar

1 Answer

I have a 1993 ford F-150 xlt and i got my brakes and rodors change and 2 days later my abs light came on


a sensor may have been pushed out of place. check behind each rotor to ensure that all sensors are about 1/16 inch away from ring.
Or just tell the mech that did the brakes to fix what he broke.

Jul 12, 2009 | 1998 Volvo V70

1 Answer

What is the easiest way to replace the air filter? on x5 diesel


The easiest way is to undo the clups around the air filter casing( some are located underneath) this is the only way to replace the filter, you may need to get under the car to remove the bottom clips.

Apr 12, 2009 | 2003 BMW 5 Series

Not finding what you are looking for?
Cars & Trucks Logo

47 people viewed this question

Ask a Question

Usually answered in minutes!

Top Dodge Experts

yadayada
yadayada

Level 3 Expert

76164 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8273 Answers

Are you a Dodge Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...