Question about 1997 Mazda 626

1 Answer

How do i add clutch fluid to 97 mazda 626 - 1997 Mazda 626

Posted by on

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that gotĀ 5 achievements.

    Sergeant:

    An expert that hasĀ over 500 points.

    Champion:

    An expert who has answered 200 questions.

  • Expert
  • 347 Answers

Should be as u open the hood very larft hand side near the master cylinder will be a clear looking canister with a lid on it take it off and sdd fluid

Posted on Oct 08, 2009

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I have a 1992 mazda 626 5 speed manual and the clutch is stuck down what do i check


You will need to check the transmission fluid. There is a dip stick for the trans just under your breather box on the driver side of the car. Start your car and let it warm up before checking the trans fluid. It should show on the stick. It should be the upper mark on the stick. If it is touching it then the fluid is ok and if not you will need to add some fluid.

Nov 25, 2012 | 1993 Mazda 626

3 Answers

1997 626 clutch pedal dropped to the floor. will not shift.145000mil clutch has never been replaced


u need a new clutch master cylinder an slave cylinder u have a fluid leak in the system

Jul 16, 2011 | 1996 Mazda 626

1 Answer

How do i bleed the clutch on a 1997 mazda 626


get a friend to help you. locate the little bleeder nut near where the line goes into the transmission. use correct wrench to loosen it make sure your clutch reservoir is full with dot3 brake fluid. after your friend pushed down on the clutch pedal open the little nut then close it. do this till not air bubbles come out and refill the reservoir

Jan 23, 2011 | 1996 Mazda 626

1 Answer

What is the problem when clutch feels loose and gears wont engage


You need to add the clutch fluid (open the engine area and see a place where the Fluid is placed) coz it might be empty or low. It should now be the empty bottle. Please tell me if it was of help

Dec 07, 2010 | 1989 Mazda 626

1 Answer

I have a 2001 mazda 626 manual transmission . The car jurk in 1st 2nd 3rd gear . Do u think I should add gear oil. Where do I add the gear oil at


It sounds more like a clutch problem than tranny. You can try the oil in there, but I think the clutch is shot. Check the fluid in the clutch master and make sure it is working right, no slipping, crunching, grinding, the jerking sounds like oil on the clutch. Check it out.

Sep 05, 2010 | 2001 Mazda 626

1 Answer

Squeeking noise when turning wheel of my 2002 mazda 626


  • Check the steering fluid, if you need to add fluid do so and also check the hose of the steering if there is a leak. If the noise is still there after you add a steering fluid then visit a local mechanic to check the pump.

Feb 12, 2010 | 2002 Mazda 626

1 Answer

I have a 1993 Mazda 626 LX five speed, and my clutch pedal will not go back up. I have pumped it like for 10 minutes, and I can not get into gear. Please help.


Have you checked the clutch master cylinder for fluid? First place I would look. If you don't know what it looks like, it will be next to the fire wall drivers side- looks like a brake master cylinder, but smaller. Just use plain brake fluid in it.

Sep 04, 2009 | 1993 Mazda 626

2 Answers

Mazda 626 - Hard to shift into gear.


With any vehicle that has a hydraulic clutch, a worn master cylinder or slave cylinder will give this very symptom. First step is to check the fluid in the resivor. If it is low, you will want to check for fluid bypassing the seals. Be sure to check under the rubber dust cover as fluid can collect there and not be readily visible. Also, if the fluid in the resivor is dark colored, it is an indication of the internal seals going bad and you will need to replace the cylinders.

Aug 17, 2009 | 2001 Mazda 626

Not finding what you are looking for?
1997 Mazda 626 Logo

Related Topics:

150 people viewed this question

Ask a Question

Usually answered in minutes!

Top Mazda Experts

yadayada
yadayada

Level 3 Expert

75051 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

7726 Answers

Are you a Mazda Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...