Question about 1996 Mercury Villager

Open Question

My Villager starts fine and idles normal but when I put it into drive or reverse it dies. It will not stay running once put into gear it just stalls every time.

Posted by on

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

After ideling a while i try to shift into reverse or to drive and it always dies .......any tips or ideas?


engine dies when shifting into reverse or drive - Third Generation ...

www.thirdgen.org/forums/tbi/346079-engine-dies-when-shifting.html
Feb 11, 2006 - engine dies when shifting into reverse or drive ... After it dies it starts right up and idles fine in park or neutral. ... these ignition items because you weretrying to cure the stalling, or, did the stalling occur after you replaced these items? ...The only thing that kept the car running was adjusting the Idle screw up.

Engine Dies When Placed In Gear***Split from Spittybug...EFI ...

dmctalk.org > ... > MAIN FORUMS > Custom DeLoreans/Mods > EFI

Jul 5, 2012 - 18 posts - ‎4 authors
Just to give an update on my car - I've been having an issue with the car stalling when moving from Park into Reverse or Drive (I have automatic). ... I have been playing with the idle advance trying to get more ... I put in the remainder of the AT fluid I had on hand and the car never died on shifting after that.

starts but dies when shifted into drive or reverse - Suzuki Forum


Jan 26, 2016 | Cars & Trucks

2 Answers

Car will start but put it in gear engine will die


engine starts with no problem; but, when I put in gear and ...

www.cargurus.com > Questions > Hyundai > Sonata

CarGurusNov 15, 2012 - The engine just fall dead when you step on the gas; it seems to jerk before ... My car does the same thing but i put it in neutral n it starts up. ... I have a 2004 kia optima it jerks when I go into reverse it was driving ... start and run fine butwhen I put it in drive or any other gear it dies! ... 2002 Hyundai Elantra GT.

Engine stalls when tranny put in Drive or Reverse - Kia Forum

www.kia-forums.com/kia-carnival...2002.../43407-engine-stalls-when-tr...

Feb 28, 2008 - 10 posts - ‎3 authors
Give it a little gas before putting in D or R and it will go. .... When I start the van cold and shift the tranny into drive or reverse.....the whole front ... won't run in forward gears - Kia Forum
10 posts
May 25, 2012
Intriguing problem - engine rough idle & hesitation ...
10 posts
Aug 31, 2011
2006 Kia Spectra engine stalls and bad idle, cleaning the ...
10 posts
Aug 30, 2010
2002 Kia Spectra Won't Go Out of Park - Kia Forum
3 posts
Oct 28, 2008
More results from www.kia-forums.com

Dec 17, 2015 | 2002 Kia Rio

1 Answer

Just replaced heater core, now car dies when put in gear


check for pinch wires around core install. also a vacume leak from same job not plugged

Dec 03, 2013 | 1998 Mercury Grand Marquis

1 Answer

1996 mercedes c280 dies when put in drive


Engine stalls or RPM fluctuates at idle up and down or dies near idle.

This problem is commonly caused by a dirty automatic idle speed control valve and throttle valve but always run a OBD2 fault code as well as the cleaning procedure. Buy a can of throttle valve cleaner (do not use carburetor spray cleaner!) from NAPA or Carquest (made by CRC chemicals) and spray it into the air intake while the engine is running, use up about 1/2 the can, engine will try to stall hold the speed up, shut it down and let it soak for 30 minutes, restart and blow out the remaining fluid, shut it down and disconnect the negative battery cable for 5 Min's to reset the base idle control

Oct 15, 2012 | 1996 Mercedes-Benz C-Class

1 Answer

Idles fine wont stay running, surges


Get the fuel mapping sensor looked at. what type of car is it?

Sep 03, 2012 | 2000 Jeep Cherokee

3 Answers

Idles fine then dies when put in drive or reverse


You may have a problem with idle speed control motor or ETC as GM calles it. here is a photo and a price from rockauto.com.
STANDARD MOTOR PRODUCTS Part # SA4 moreinfo.gif
Motor Assembly sa4_full.jpg $110.99

Apr 18, 2009 | 1990 Cadillac Fleetwood

1 Answer

91 camry starts and shuts off when put in drive or reverse


I was an ASE master auto tech for 13yrs and have seen this problem before. It sounds like the idle air control valve on the intake manifold has stopped working and the idle speed is not being controlled(letting the engine idle too slow which causes a stall when put under a load such as putting it in gear). Try giving it a little throttle while putting it in gear if that works let off the throttle if it dies you will know the Idle Air controll is not working.

Oct 12, 2008 | 1991 Toyota Camry

Not finding what you are looking for?
1996 Mercury Villager Logo

Related Topics:

141 people viewed this question

Ask a Question

Usually answered in minutes!

Top Mercury Experts

yadayada
yadayada

Level 3 Expert

76164 Answers

fordexpert

Level 3 Expert

5522 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Are you a Mercury Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...