Question about 2007 Chevrolet Tahoe

Open Question

Got the keys locked in 2007 Tahoe. had it unlocked, now the key won't unlock the doors.

Posted by on

  • njazrael71 May 11, 2010

    How did you have it unlocked? If remotely unlocked via company, they killed the signal from the key. If unlocked via a lockout company using a slim jim or something, it sounds like they may have broken a wire or something.

×

Ad

2 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
New users get to try the service completely Free afterwhich it costs $6 per call and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
  • 62 Answers

SOURCE: 2004 chevy tahoe tailgate won t unlock theres no

I fixed my 2005 from info at following site http://www.chefseattle.com/blog/site-news/suburban-rear-liftgate-wont-unlock-how-to-fix/
It may help you too.

Posted on Jun 12, 2010

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

2007 sonata driver door won't unlock with key fob


door reciever or lock has issues
did you scan the car first.
does the receiver put 12dc to the unlock solenoid.
if yes the solenoid is bad.
if not the receiver has issues. (check connections first there)

Jul 15, 2015 | 2007 Hyundai Sonata Limited Sedan

1 Answer

Key won t unlock doors


lost the other fob>>> ?????
never own a car with 1 fob.
and if one fob messes up, the battery inside is dead. (or worse)
if just lock fails the button is bad, if one fob false, and they do
its just cheezy switch. (can be cleaned)
use the other FOB, if it fails, post.

Jan 25, 2014 | 2007 Honda CR-V

1 Answer

2007 toyota matrix hatchback door won't reset


Read manual. It should direct you to location where you can manualy unlock hatch. Look for little trap door. It should be located very near lock.
Hope this would help

Jan 10, 2013 | Cars & Trucks

1 Answer

How do you re-program the security code on a 2007


FORD KEY PADS
  • Enter permanent factory code
  • Press the 1/2 button within 5 seconds to enter programming mode
  • Within 5 seconds enter new code, doors will lock, unlock to verify code, this erases previous codes remotes will also need to be programmed. (MAYBE)
KEY PADS/REMOTES
  • Insert key, turn ignition off-to- on eight times in succession, ending with key in on position doors will lock, unlock to verify in programming mode
  • Press any button on new remote, doors will lock, unlock to verify
  • Do the previous step with the second remote, doors will lock unlock to verify.
  • Turn ignition off. Doors will again lock, unlock to verify.
NOTE-Some vehicles use 5 turns of the key instead of 8

Jun 05, 2010 | 2007 Ford Explorer Eddie Bauer

1 Answer

Door locks stoped working


See if there is a fuse for your door locks.

Good Luck!

Sep 15, 2009 | 2006 Chevrolet Tahoe

1 Answer

How to program key fob. I have the fobs.


Transmitter Programming Procedure
Close all the vehicle doors.
Insert the ignition key into the ignition lock cylinder.
Press and hold the door unlock switch.
While holding the door lock switch in the unlock position, cycle the ignition ON, OFF, ON, OFF.
Release the door unlock switch. The doors will lock and unlock to confirm the program mode.
Press and hold the LOCK button and the UNLOCK button simultaneously on the transmitter. After a delay of approximately 15 seconds, the doors will lock and unlock to confirm the programming of the transmitter.
Turn the ignition switch to the RUN position in order to exit the keyless entry transmitter mode.
Operate the transmitter functions in order to verify correct system operation.
Good luck

Jun 25, 2009 | 2002 Chevrolet Tahoe

1 Answer

Programming used key fob for a 2000 tahoe


get in your truck close all the doors put your key in the ignition push and hold your unlock button on the door panel turn the key on then off then on then off release the onlock button at this time the lock should cycle lock then unlock by them self if they did push and hold your lock and the unlock buttons on your remote at the same time for 15 seconds the lock should cycle agian and you are programmed

Jun 04, 2009 | 2001 Chevrolet Blazer

2 Answers

Alarm problem on 2004 chevy tahoe


you will have to write your vehicles vin number down wich is if you look throught the windshild on the drivers side you will see it its a little plate with numbers but right down the vin number and take you drivers license and Registration with you to the chevy dealer ship and request the remote for that vehicle. and they should be able to get you one. as far as i know the remote is the only way to get the alarm off. I hope this helps you

Mar 21, 2009 | 2004 Chevrolet Tahoe

Not finding what you are looking for?
2007 Chevrolet Tahoe Logo

Related Topics:

474 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts

yadayada
yadayada

Level 3 Expert

76630 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8514 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...