Question about 2006 Chevrolet Colorado

1 Answer

I was hearing a crunching sound comming from my truck while going around turns, accelerating, and decelerating. The shop told me that they adjusted and lubed my cab mounts. I was just wondering how they lube them. Do they just apply grease to the outside rubber on the mount? And how can you adjust them? Don't they just have a bolt and a nut that has a torque spec?

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Master
  • 1,596 Answers

The "SHOP" Lied to you as there is NO Such Procedure, they MAY have SPRAYED some Penitrating Oil on them but thats ALL they Could Have Done, This sounds like a SUSPENTION Problem, SEAT MOUNTS, or Simply the Mounts Groaning and May Need Replaced all together. If CV Joints have been ruled OUT.

Posted on Oct 08, 2009

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

2003 ford sport trac front grinding noise from drivers side when sharp left turn


go to the magicmechanic website and send him this--hes the best there is and will rply

Jan 19, 2015 | 2003 Ford Explorer Sport Trac

1 Answer

I have a 98 Gmc Jimmy and everytime I accelerate it makes this noise around the front passenger side and it sounds like when you would put a card in the spokes of a bicycle...? Any ideas of what this


Sounds like you have a bad wheel bearing. Could also be a CV. Make sure you know what wheel before you replace anything. Jack it up and spin the wheel by hand. If correct wheel you will hear it. Hope this helps

Oct 26, 2012 | GMC Cars & Trucks

1 Answer

High pitch nosie from rear end of 2004 ford f-150 supercrew


Does the sound change while accelerating or decelerating?? If it does i would suspect a carrier bearing or a pinion bearing going bad..If its consistant,,and doesnt change with acceleration or deceleration,,then it may be a axle bearing..

Sep 29, 2011 | 2004 Ford F150

1 Answer

Cv joint question


Stationary lock to lock turning, will not damage the CV joints, they are designed to turn in this manner, to test a CV joint to see if it has damage, go to an empty parking lot, stop the car, turn the steering wheel full left, accelerate kinda hard, do you hear a clicking or clunking noise? repeat in reverse and on the right hand side. Any noises and your CV joints may be worn, also inspect the CV boots for tears and leakage by turning full left and looking at the boot, then full right. Hope this helps, let me know

Jan 23, 2010 | 2008 Ford Fusion

2 Answers

Front end noise


A suspension part is worn out - lift the front of the car and check the bushings (most likely), the pivots and the ball bearings.

Jan 20, 2010 | 2004 Ford Focus

2 Answers

CV Joints


You will usually hear a real loud clicking sound when your turning at a tight radius in either direction. Check the rubber boots over the joints. If they are cracked or ripped off you will need to replace them.There will be 2 on each side. If they are real noisy just replace the entire half-shafts. Shop around for axle shaft assy prices, typically $100.00 - $300.00 each side.

May 26, 2009 | 1990 Suzuki Swift

1 Answer

Hooting sound when driving


I had a similar problem. Turned out it was a vacuum line on the firewall on the passenger's side had come off. When you accelerate, the line sucks air and makes that long "hooooooooooot" until you let off the gas. Have you noticed it's burning even MORE gas? You'll need a bright light, even in sunlight to see the lose hose line.

Nov 29, 2008 | 1996 Ford F150 Regular Cab

1 Answer

Clunking noise w/ acceleration


Ya know it sounds like one of the U-Jonts in the front drive line to the front wheels has failed or even one of the driveline U- joints is either Dry and lost its bearings and is worn out,
One of the easiest ways to make sure its not the engine is while driving down a hill put the car in neutral, turn off the engine coast down a small hill and turn to either direction and see if you still hear it , if you still hear it its gonna be somewhere in the drive lines, becareful you will not have power steering or power brakes with the engine off, but you can restart the engine inn neutral at any time . Please let me know.

Aug 24, 2008 | 2004 Ford Expedition

Not finding what you are looking for?
2006 Chevrolet Colorado Logo

57 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts

yadayada
yadayada

Level 3 Expert

75797 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22114 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8140 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...