Question about Chevrolet Suburban 1500

1 Answer

How do you run the codes for a obd 1 - Suburban 1500 Chevrolet Cars & Trucks

Posted by on

  • nicco48 Oct 08, 2009

    ty this was very helpfull im pretty spoiled with my 05 truk and codes are easy to run on obd 2. this is my first obd 1st truck

×

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    President:

    An expert whose answer got voted for 500 times.

  • Master
  • 2,600 Answers

First thing you want to do is ground the test terminal which is the top right hand terminal, just make a jumper wire and attach the other end to the terminal to its left. When you look at the OBD plug under the steering column, the two top right hand terminals need to be grounded.

Move your ignition switch to "on", DO NOT TURN THE ENGINE OVER.
Your "Check Engine" light should be flashing. The codes stored here will flash the "check engine" light. It starts by flashing 12. That will loook like one flash, a pause, then two flashes....a longer pause and then the next code. Remember when you first see the codes flash and you write down code 12, this is not a fault code, it is more like a communication between the computer and diagnostics, it is only to get your attention and show you how the flash works, Each code is flashed three times, then it moves on to the next. When all the codes stored are flashed three times, you may see code 12 come again, that will signify the end, sometimes it comes up, sometimes it does not.

These codes are kept in numerical order not the order of when the problem happened, they so give a chronologocal time line of events. They are simply listed here.

When you are done with the codes, they can be cleared by removing power to the power to the ECM for 30 seconds. This is best done by removing the fuse the powers the ecm and not disconnecting the battery for all of the vehicle.

Hope this helps, I've done it quite a few times for my Tahoe.

Posted on Oct 08, 2009

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

What are the probable causes of DTC P0171?


P0171 refers to System to lean on bank #1

Aug 07, 2015 | Dodge Cars & Trucks

1 Answer

Check engine light code p2196,p2197, po300 ,304,305,306,p2 ,Im freeking out.


P0300 Random/Multiple Cylinder Misfire Detected P0301 Cylinder 1 Misfire Detected P0302 Cylinder 2 Misfire Detected P0303 Cylinder 3 Misfire Detected P0304 Cylinder 4 Misfire Detected P0305 Cylinder 5 Misfire Detected P0306 Cylinder 6 Misfire Detected P0307 Cylinder 7 Misfire Detected P0308 Cylinder 8 Misfire Detected P0309 Cylinder 9 Misfire Detected P0310 Cylinder 10 Misfire Detected P0311 Cylinder 11 Misfire Detected P0312 Cylinder 12 Misfire Detected P0313 Misfire Detected with Low Fuel P0314 Single Cylinder Misfire (Cylinder not Specified) P0315 Crankshaft Position System Variation Not Learned P0316 Misfire Detected On Startup (First 1000 Revolutions)

Read more at: http://www.obd-codes.com/trouble_codes/
Copyright © OBD-Codes.com
-----------------------------------------------------------------------
P2195 O2 Sensor Signal Stuck Lean Bank1 Sensor 1 P2196 O2 Sensor Signal Stuck Rich Bank1 Sensor 1 P2197 O2 Sensor Signal Stuck Lean Bank2 Sensor 1 P2198 O2 Sensor Signal Stuck Rich Bank2 Sensor 1

Read more at: http://www.obd-codes.com/trouble_codes/
Copyright © OBD-Codes.com http://www.obd-codes.com/p0002

May 07, 2015 | 2006 Ford Taurus SEL

1 Answer

I have 2007 hhr and the code is p0171


This code is triggered by the first downstream (front) O2 sensor. The sensor provides a reading of the air:fuel ratio leaving the engine's cylinders, and the vehicles powertrain/engine control module (PCM/ECM) uses that reading and adjusts to keep the engine running at that optimum ratio of 14.7:1. If something is not right and the PCM cannot maintain the 14.7:1 ratio, but rather there is too much air, it triggers this code.

Read more at: http://www.obd-codes.com/p0171
Copyright © OBD-Codes.com

Feb 25, 2015 | 2007 Chevrolet Chevrolet HHR LT

2 Answers

2006 buick rainer obd code30


in 2006 there is no obd system even code 30 your system is obd2 and code start with P????
obd system stop in 1995

Oct 14, 2013 | 2006 Chevrolet Trailblazer

2 Answers

Mazda 1994 626 - OBD-1 Checkup?


There may be some codes in memory that a code reader can reveal.

Aug 16, 2017 | 1994 Mazda 626

1 Answer

Ssei is it an obd 1 or an obd 2, my engine lite is on but I get no reading from an obd 2 and a conflick of wich 2 terminals to cross for an obd 1


94 and 95 bonneville's have a odb1 system but the plug under the dash for the code reader is for odb2/.
you have to get a code reader that will read odb1 and odb2 with a manufacture special plug to read them.
also the computer in the 94-95 are only used in those 2 years.
new one at most auto parts stores is about $100.00
cheap compared to other years.
if you have lots of codes and it runs good but just turns itself off all the time it's the computer.
I had to replace 2 so far one in a 94 and one in a 95.

Jan 25, 2011 | 1995 Pontiac Bonneville

2 Answers

Im buying a 1986 bmw 325e and it has a check engine light im familiar with locations and diagnostics of obd 1 and 2 vehicles but im not sure how and where to pull codes off of this vehicle is there a plug...


You can get hte codes from this BMW by turning the ignition key to the run position and then press the accelerator pedal to the floor 5 times, it will enter the diagnostic mode, count the flashes just like obd 1. Hope this helps, let me know

Nov 29, 2009 | 1986 BMW 3 Series

1 Answer

OBD II code P0133 (O2 bank 1 sensor 1) which


It is the front sensor, if your car is the type that has 2 front sensors it will be the one closest to the timing chain / belt (left hand side of engine)

Nov 27, 2009 | 2005 Suzuki Forenza

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

20 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts

yadayada
yadayada

Level 3 Expert

75822 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8215 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...