Question about 1998 Ford Explorer

1 Answer

Pulling out the starter motor of ford explorer 1998

How to pulled out the starter motor for ford explorer 1998 model automatic and how can i put it back the new starter motor

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Master
  • 424 Answers

Disconnect the battery. Unbolt starter,disconnect wiring. Reinstall wiring and starter. Reconnect battery. You will need a 10mm socket and a 13 mm socket for the bolts and nuts.

Posted on Oct 09, 2009

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Changing engines Ford Explorer 4l ohc.


Yes, same block setup, with most all attachments also. should be an easy pull and remove.

Jun 12, 2017 | Ford Cars & Trucks

1 Answer

For ranger new starter wont stop running


Starter Relay The starter motor solenoid relay switch (11450) consists of a pull-in coil, a contact disc, and two terminal contacts. Battery voltage is always present at the relay positive terminal. When the ignition switch (11572) is in the START position, the pull-in coil is activated and pulls the contact disc into contact with both terminal contacts. This allows battery current to pass through the starter motor solenoid relay switch to the starter solenoid (11390). The starter solenoid is deactivated when the ignition switch is in the RUN or OFF position.
Maybe something is hooked up wrong ! Or the starter relay is bad
May

Mar 11, 2015 | 1998 Ford Ranger

1 Answer

Reverse stopped working in 1998 ford explorer


reverse band in trans broke, will have to pull the trans and have it gone through,

Oct 15, 2014 | 1998 Ford Explorer

1 Answer

1998 ford explorer/ need location to remove and


If your going to be removing all of this I recommend you get the Haynes repair manual on the vehicle so you have the illustrations and directions for dis-assembly and assembly of the starter. The starter should be located on the bottom right of the engine where the Transmission attaches.

Jul 11, 2010 | 1998 Ford Explorer

1 Answer

My truck makes a sound like there was a chaing loose. there already tide the chsin in the back cause it was loose. an they put new tensonrs


The 4.0 sohc motor has 3 chains. It is a common failure. You have to pull the motor to fix the chains.

Mar 31, 2010 | 1998 Ford Explorer

1 Answer

How to take a starter off 1998 windstar


sww~us~en~file=ani_caut.gif~gen~ref.gif WARNING: WHEN SERVICING STARTER MOTOR (11002) OR PERFORMING ANY MAINTENANCE IN THE AREA OF THE STARTER MOTOR , NOTE THE HEAVY GAUGE INPUT LEAD CONNECTED TO THE STARTER SOLENOID (11390) IS HOT AT ALL TIMES. MAKE SURE THE PROTECTIVE CAP IS INSTALLED OVER THE TERMINAL AND IS REPLACED AFTER SERVICE.
  1. Disconnect battery ground cable
  2. Raise the vehicle on a hoist.
  3. Remove the starter solenoid safety cap.
  4. sww~us~en~file=ani_caut.gif~gen~ref.gif CAUTION: When disconnecting hardshell connector at S terminal, grasp the plastic shell and pull off. Do not pull on wire. Be careful to pull straight off to prevent damage to the connector and S terminal. If any part of the connection is damaged, replace the damaged components.
  5. Disconnect starter cable and push-on connector from starter solenoid.
  6. Remove upper bolt.
  7. Remove lower bolt and starter motor.

Mar 16, 2010 | 1998 Ford Windstar

1 Answer

Location of starter relay on 98 ford explorer


starter relay is under hood on the drivers side fender area.034ad7c.gif
  1. Disconnect the battery ground cable (14301).
  1. Disconnect the starter motor solenoid relay switch wiring.
    1. Remove the protective cover.
    1. Disconnect the push-on electrical connector.
    1. Remove the nuts.
    1. Remove the cable.
    2. d57efc7.gif
    Remove the starter motor solenoid relay switch (11450).
    1. Remove the engine sensor/generator wires.
    1. Remove the bolts and ground wire.
    1. Remove the starter motor solenoid relay switch
    2. 1056336.gif

Oct 22, 2009 | 1998 Ford Explorer

2 Answers

How to remove a starter on a 2002 ford explorer


  1. Disconnect the negative battery cable.
  2. Properly raise and support the vehicle.
b58491e.gif
Disconnect all wires connected to the starter, including this ground wire on the starter mounting bolt stud

  1. Click to Enlarge

    1. Tag and disconnect the wiring at the starter.
    1. WARNING
    1. When detaching the hard-shell connector at the S-terminal, grasp the plastic shell to pull it off. Do not pull on the wire itself. Ensure to pull the connector straight off to prevent damage to the connector and S-terminal. If any part of the connector is damaged, replace the damaged component.
  • daab222.gif
    Remove the starter motor (arrow) mounting bolts . .

    Remove the starter mounting bolts and remove the starter.

    5c220c9.gif
    . . . then remove the starter—be careful, the starter motor can be quite heavy

    To install:
    1. Position the starter motor against the engine and install the mounting bolts. Tighten the mounting bolts to 15–19 ft. lbs. (21–27 Nm).
    2. Install the starter solenoid connector by pushing it straight on. Ensure that the connector locks in position with a notable click.
    Install the starter cable nut to the starter solenoid B-terminal. Tighten the nut to 80–123 inch lbs. (9–14 Nm).
    1. Connect any remaining wiring to the starter motor.
    2. Lower the vehicle.
    3. Connect the negative battery cable.

    Oct 11, 2009 | 2002 Ford Explorer

    3 Answers

    How do you replace the starter in a 98 ford explorer V8


    REMOVAL & INSTALLATIONSee Figure 3 to 6
    1. Disconnect the negative battery cable.
    2. Raise the front of the vehicle and install jackstands beneath the frame. Firmly apply the parking brake and place blocks in back of the rear wheels.

    077de93.jpg

    Fig. Disconnect all wires connected to the starter, including this ground wire on the starter moutnting bolt stud

    1. Tag and disconnect the wiring at the starter.
    WARNING When detaching the hardshell connector at the S-terminal, grasp the plastic shell to pull it off. Do not pull on the wire itself. Ensure to pull the connector straight off to prevent damage to the connector and S-terminal. If any part of the connector is damaged, replace the damaged component.

    d761bb2.jpg


    Fig. Some starters use a self-threading bolt to hold the starter cable


    3a3fb11.jpg


    Fig. Remove the starter motor (arrow) mounting bolts ...
    1. Remove the starter mounting bolts and remove the starter.
    bf28d85.jpg


    Fig. ..then remove the starter-be careful, the starter motor can be quite heavy


    To install:
    1. Position the starter motor against the engine and install the mounting bolts. Tighten the mounting bolts to 15-19 ft. lbs. (21-27 Nm).
    2. Install the starter solenoid connector by pushing it straight on. Ensure that the connector locks in position with a notable click.
    Install the starter cable nut to the starter solenoid B-terminal. Tighten the nut to 80-123 inch lbs. (9-14 Nm).
    1. Connect any remaining wiring to the starter motor.
    2. Lower the front of the vehicle and remove the wheel blocks.
    3. Connect the negative battery cable.

    I hope help you with this (remeber rated this help). Good luck.

    Sep 09, 2009 | 1998 Ford Explorer

    1 Answer

    Need to know how to put a oil pump in a 1998 ford explorer xlt 5.0 liter


    The oil pump is internal.Unless you can get the oil pan off,you can't do the job.I'd think you'd have to pull the engine on the explorer especially if it's 4x4.Thats a tight fit.Hope this helps!

    May 19, 2009 | 1998 Ford Explorer

    Not finding what you are looking for?
    1998 Ford Explorer Logo

    Related Topics:

    401 people viewed this question

    Ask a Question

    Usually answered in minutes!

    Top Ford Experts

    yadayada
    yadayada

    Level 3 Expert

    75077 Answers

    Colin Stickland
    Colin Stickland

    Level 3 Expert

    22095 Answers

    fordexpert

    Level 3 Expert

    5471 Answers

    Are you a Ford Expert? Answer questions, earn points and help others

    Answer questions

    Manuals & User Guides

    Loading...