Question about 1999 Suzuki Vitara

1 Answer

What are the torque settings to tighten the head on a Suzuki G15A cylinder head and what are the tappet settings ?

Posted by on

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

    Sergeant:

    An expert that has over 500 points.

  • Expert
  • 293 Answers

3 step torque: 25 Ft-lb, 35 Ft-lb, 50 Ft-lb.
Valve lash: Both for intake and exhaust: 0.15 MM

Posted on Oct 09, 2009

Testimonial: "Great , many thanks"

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Hey there I need the exhaust and Intake(valve) clearance for a komatsu 300-6 please


note Perform the valve clearance check and adjustment at the engine cold state. 1.Remove all of the ignition coils. 2.Remove the cylinder head cover.
caution Turn the crankshaft always clockwise. 3.Turn the crankshaft clockwise, and align the timing mark on the exhaust camshaft sprocket against the upper face of the cylinder head as shown in Figure. Therefore, No.1 cylinder goes to the compression top dead center. 4.Using a thickness gauge, measure the valve clearance with the arrow shown in Figure. If deviated from the standard value, make note for the valve clearance.
Standard value:

    Intake valve 0.20 ± 0.03 mm (0.008 ± 0.0012 inch)
    Exhaust valve 0.30 ± 0.03 mm (0.012 ± 0.0012 inch)
5.Turn the crankshaft clockwise 360 degrees, and put the timing mark on the exhaust camshaft sprocket in position shown in Figure. Therefore, No. 4 cylinder goes to the compression top dead center. 6.Check the valve clearance with the arrow shown in Figure. In the same procedure as 4.
7.If the valve clearance is deviated from the standard value, remove the camshaft and the valve tappet. For the camshaft removal, refer to Camshaft Removal and Installation . 8.Using a micrometer, measure the thickness of the removed valve tappet. 9.Calculate the thickness of the newly installed valve tappet through the following equation.
A: thickness of newly installed valve tappet
B: thickness of removed valve tappet
C: measured valve clearance
Equation

    Intake valve: A = B + [C - 0.20 mm (0.008 inch)]
    Exhaust valve: A = B + [C - 0.30 mm (0.012 inch)] note The valve tappet ranges 3,000 - 3,690 mm (0.1181 - 0.1453 inch) and has 47 types per 0.015 mm (0.0006 inch). The thickness below a decimal point is stamped on the reverse side of the valve tappet. 10.Install the valve tappet selected through the procedure 9, and put the camshaft in position. For the camshaft installation, refer to Camshaft Removal and Installation .
    11.After installing the timing chain, measure the valve clearance using the procedure 3 to 6. Confirm the clearance is within the standard value.
    caution Completely remove all the old FIPG, which might be remaining among the components. 12.After completely removing the liquid gasket adhering on the timing chain case, cylinder block and cylinder head, degrease them with white gasoline.
    caution The cylinder head cover should be installed within 3 minutes of applying liquid gasket.
13.Apply a 4 mm bead of liquid gasket as illustrated.
Specified sealant:
    THREE BOND 1217G or equivalent
14. Install the cylinder head cover and tighten the tightening bolts using the following procedures.
(1) Temporarily tighten to the following torque in order shown in the illustration.
Tightening torque: 3.0 ± 1.0 N·m (27 ± 8 in-lb)(2) Tighten to the specified torque in order shown in the illustration.
Specified torque: 5.5 ± 0.5 N·m (49 ± 4 in-lb)15.Install the ignition coils.

Jan 23, 2017 | Cars & Trucks

1 Answer

I need the head bolt torque specs and sequence for a 2008 Suzuki reno 4 cylinder


well it's at alldata.com and at suzuki pitstop plus dot com.
here ill do that for you....
4 banger no displacement stated, now that is a challenge.


now the words..... USA car... 2.0L vin Z

Cylinder head bolts. Tighten the cylinder head bolts gradually and in the sequence shown. Tighten the cylinder head bolts to 18 ft. lbs. (25 Nm) and turn the bolts another 3 turns of 90 degrees using the angular torque gauge KM-470-B.




25750556-4duymjxl1ar05igx5z0a5r0z-5-0.jpg

Jun 17, 2015 | 2008 Suzuki Reno

2 Answers

What is the cylinder head bolt torque settings fir a 4g69 mitsubishi engine ?


BOLT INSTALLATION


Apply engine oil to the thread of the bolts and to the washers.
Tighten the bolts to the specified torque, using the tightening sequence shown.
Tightening torque: 54 ft-lb +/- 2 ft-lb
Loosen all bolts fully in the reverse order of tightening.
Re-tighten the loosened bolts to the specified torque in the tightening sequence shown.
Tightening torque: 15 ft-lb +/- 1 ft-lb
This step is to make it easier to ensure you are making 90 degree turns. Make a paint mark across each bolt head and cylinder head.
Tighten the cylinder head bolts 90 degrees in the specified order.
Tighten the bolts another 90 degrees in the specified order and check that the paint marks on the cylinder head bolts are aligned with the paint marks on the cylinder head.
Link to the guide for this engine: http://www.mivec.co.nz/tech/4G9x_Engine_Manual.pdf



Aug 04, 2014 | 2007 Mitsubishi Outlander 2.4

1 Answer

I need the torque settings for toyota corola 1993 cylinder head torque please ?


Hi Manuel, There are a number of different engines used in the Corolla, knowing which would be a great help. The engines used in the 1993 are of the 'A' series and 'E' series. The torque for the A series is 29 nm + 90 degrees. When removing the head begin loosening from the outer bolts. When the head is off have it inspected for warpage and skimmed if it is required. Tightening any cylinder head always begins at the middle or centre and works outwards. As my friend has said, the camshaft caps are tightened to 9 nm and the inlet manifold goes to 24 nm, and the exhaust is 27 nm. The tappet cover I think is 29 nm. The tappet cover is tightened on the A series with nuts onto the plug tubes. Regards John

Mar 29, 2014 | 1993 Toyota Corolla

1 Answer

Torque specifications for cylinder head


Per Suzuki, tighten the cylinder head bolts to 25 Nm (18 lb-ft) and turn the bolts another 3 turns of 90 degrees using the angular torque gauge KM-470-B. If this helps, please say so! Thanks! :-)


12_16_2011_4_57_00_pm.jpg

Nov 09, 2011 | 2004 Suzuki Forenza

1 Answer

Wats the torque setting on the head bolts on a 1995 suzuki grand vitara v6 2l


Install cylinder head to block.
After applying oil to cylinder head bolts, tighten them gradually
as follows.

(1)Tighten all bolts to 53 N.m (5.3 kg-m, 38.5 lb-ft) according to
numerical order in sequence

(2)In the same manner as in (1), tighten them to 84 N.m
(8.4 kg-m, 61.0 lb-ft).

(3) Loosen all bolts until tightening torque is reduced to 0 in reverse
order of tightening.

(4)In the same manner as in (1), tighten them to 53 N.m
(5.3 kg-m, 38.5 lb-ft).

(5) In the same manner as in (1) again, tighten them to specified
torque....105 N.m (10.5 kg-m, 76.0 lb-ft)

This was taken from SQ416 manual from www.suzukinfo.com
I hope this helps.

Jul 22, 2011 | Suzuki Vitara Cars & Trucks

1 Answer

Whats is te cylinder heads torque for suzuki aerio 2.3 lts


Hi! Please don't forget to rate! Thanks!



c17hydro_181.gif

Cylinder head bolt torque sequence-2.0L and 2.3L engines



Apply engine oil to the bolt threads and tighten the cylinder head bolts, in sequence, using the following 6 Steps:

  • Step 1: 38.5 ft. lbs. (53 Nm)
  • Step 2: 61 ft. lbs. (84 Nm)
  • Step 3: Loosen all of the cylinder head bolts
  • Step 4: 38.5 ft. lbs. (53 Nm)
  • Step 5: 76 ft. lbs. (105 Nm)
  • Step 6: Bolt M6 (bottom left of cylinder head) - 8 ft. lbs. (11 Nm)

May 12, 2011 | 2003 Suzuki Aerio

1 Answer

What are the torque settings for a 1997 audi a3 1.6 cylinder head


The torque settings for a 1997 Audi A3 1.6 cylinder head:

1. Tightening sequence
tdisline_167.jpg
2. Cylinder head instructions:
2.1. Renew bolts: Yes.

3. Tightening torques:
3.1. Stage 1 - Tighten: 40 Nm.
3.2. Stage 2 - Tighten: 90 degrees.
3.3. Stage 3 - Tighten: 90 degrees.


Please do rate my response. Thanks!

Jan 22, 2011 | Audi A3 Cars & Trucks

1 Answer

Need torque settings for cylinder head bolts on a 52 reg skoda fabia 1.4 16v any help much appreciated thanks


Torque settings for cylinder head bolts for Skoda Fabia 1.4 16v

Cylinder head bolts tightening order:

tdisline_116.jpg

IMPORTANT NOTE: RENEW BOLTS!

Stage 1: Tightening torque = 30 Nm
Stage 1: Tightening torque = 90 Degrees
Stage 1: Tightening torque = 90 Degrees

Please do rate my response. Thanks!

Dec 17, 2010 | Volkswagen Polo Cars & Trucks

1 Answer

Cant find out the cylinder head torque settings for a 1997 2.0L ptrol 24 valve vitara


Cylinder head instructions
Cylinder head
Renew bolts No
Stage 1 Tighten 35 Nm
Stage 2 Tighten 75 Nm
Stage 3 Tighten 105 Nm

Feb 13, 2010 | 1999 Suzuki Vitara

Not finding what you are looking for?
1999 Suzuki Vitara Logo

340 people viewed this question

Ask a Question

Usually answered in minutes!

Top Suzuki Experts

yadayada
yadayada

Level 3 Expert

75066 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Boyet Soriano
Boyet Soriano

Level 2 Expert

293 Answers

Are you a Suzuki Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...