Question about 2005 Chrysler PT Cruiser

2 Answers

I have pt cruiser showing mulfunction cersor light

I have2005 4 cyclinder pt cruiser showing mulfunction cersor light and I did check my gas cap and my gas is chevron and I put 89 octain

Posted by on

2 Answers

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Chrysler Master
  • 578 Answers

Thought that the PT Cruiser wanted 87 Octane fuel....Your extra expense outlay will hurt nothing but your wallet.
Fill it up again. Be sure the tank is FULL. Restore the gas cap and give the vehicle 2 or 3 days to restore the "check engine" light. Malfunction Cursor is not (normally) in Crysler's auto maintenance software!!
If you continue to get the display - take it to Autozone and they will do a diagnostic on it for free - and TELL YOU what is wrong.....

Posted on Oct 08, 2009

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 3 Answers

Brand and octain dont matter if your cap isnt on tight it will come on or if you have replaced the cap some times it will come on it will just take a few times of driving it for it to shut off some where around 300 to500 miles

Posted on Oct 08, 2009

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

CODES P0441 AND P0304 CAME UP ON TEST? WHERE DO I START ON TRYING TO FIGURE OUT THE PROBLEM


P0441 = EVAP PURGEFLOW MONITOR that means insufficient or excessive vapor flow detected during evaporative system .
P0304= a misfire in cylinder # 3 answers to these p0441 a bad gas cap possible , and p0304 possible bad coil on cylinder #3, try clearing codes and see if they show back up or you get bad performance , then try replacing gas cap and then coil pack . I really hope this gets you on the right track .
Woody

Mar 05, 2015 | 2004 Chrysler PT Cruiser

1 Answer

07 pt cruiser gas cap light on


I would guess that if the cap is actually secure, then it needs a new seal ring on the cap, or a new cap with a good seal.

Feb 07, 2014 | 2007 Chrysler PT Cruiser Touring Hatchback

1 Answer

2005 PT Cruiser showing P0456 and P0522. Cranks but wont start.


The sensor that is most likely causeing the problem is the low oil pressure sensor. It is telling the cpu that you have a problem that unless you correct it, the motor will suffer serious damage from insufficient lubrication.Have the oil pressure checked with a manual gauge then replace the sensor unit if faulty.

Feb 23, 2013 | 2005 Chrysler PT Cruiser

1 Answer

Check engine light comes on periodically, it does'nt change the way it runs but I am always concerned that something may be wrong.


I just had this problem with my 2005 PT Cruiser. I took the car to my local repair shop (Chrysler has abandoned this area in Florida) and had it connected to a diagnostic computer. Guess what? Loose gas cap. Looking at the cap you can see the gasket is getting funny. Repair shop recommended buying a new gas cap.

Mar 22, 2011 | 2005 Chrysler PT Cruiser

1 Answer

Ongoing P0441 purge code on 2003 PT Cruiser GT. I


if you have replace the purge solenoid the problem is either the vaccum supply hose is loosing vaccum or the purge side is hose is either blocked or cracked.

Apr 21, 2010 | 2003 Chrysler PT Cruiser

1 Answer

Started the mulfunction cersor light went on 2 days ago


if check engine light is on a garage can hook up an ob2 and tell you whats wrong

Oct 08, 2009 | 2005 Chrysler PT Cruiser

2 Answers

Check Engine Light is on


Internal memory fault,Will need replacement ecm.

Jun 20, 2009 | 2002 Chrysler PT Cruiser

1 Answer

2006 pt cruiser, check engine light came on. Shortly after, gas cap light. Replaced gas cap and reset. Today bith lights came on again.


are you fueling car with key "on"? That will cause light to come on. Disconnect battery for 1 hour and this will reset "keep alive memory" and clear codes from memory. Drive car for 10 miles so computer can relearn engine parameters. It may run rough during this period.

Jun 03, 2009 | 2006 Chrysler PT Cruiser

1 Answer

2005 pt cruiser check engine light came on put a diagnostic code tester on and it came up code po457 and po456 what would this mean?


P0457 is a loose gas cap, P0456 is a small evap system leak. The seal on your gas cap is probably worn. Replace the cap, clear the codes with either a diagnostic tester or by disconnecting the battery for a few minutes and reconnecting it. It will take a few days for the code to come back if it isn't fixed, but that usually does the trick. I hope this helps.

Apr 27, 2009 | 2005 Chrysler PT Cruiser

Not finding what you are looking for?
2005 Chrysler PT Cruiser Logo

342 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chrysler Experts

yadayada
yadayada

Level 3 Expert

75822 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8195 Answers

Are you a Chrysler Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...