Question about 1998 Ford Expedition

1 Answer

Will an engine from a 94-96 crown vic fit a 98 expedition 4.6l w code

Posted by on

Ad

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Corporal:

    An expert that hasĀ over 10 points.

    Mayor:

    An expert whose answer gotĀ voted for 2 times.

    Problem Solver:

    An expert who has answered 5 questions.

  • Contributor
  • 12 Answers

The block will fit, however, then electrical connections may not all be the same. It will have a similar setup though

Posted on Oct 28, 2009

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How to change engine coil on 98 crown vic


to much work i would get a new engine

Oct 19, 2011 | 1998 Ford Crown Victoria

2 Answers

Replace all four oxgen seners on my ford expedition and even clear the codes 1151 and po155 with code scanner but still comes back on 5.4 4x4


You could have dirty injectors, a vacuum leak, faulty MAF sensor and/or a clogged catalytic converter. Most likely your 02 sensors were fine and didn't need to be replaced. Just because you have an sensor fault code does not mean the sensor is bad, in fact the majority of the time it's working just fine.

Jul 22, 2011 | 2001 Ford Expedition

1 Answer

I have 98 crown vic check engine light was not on in till i went to emission testing code read catylc thershold to low


you will need to take it to an exhaust shop and have the catalytic converters replaced unfortunately

Feb 20, 2010 | 1996 Ford Crown Victoria

1 Answer

2000 crown vic motor overheating and freezing up after 1/2 hour. New oil, fan, thermostat. water level ok. A/C was on.


Is the engine itself hot? or the car? If the engine is warm, check the engine coolant, and see if their are any holes or leaks..

May 23, 2009 | 2000 Ford Expedition

2 Answers

Wiper motor replacement for a 99 crown vic


I replaced the same part on a 1994 Crown Vic. There are a few bolts which go through rubber mounts on the firewall and that is how the wiper motor fits against the firewall. There is a clip on the wiper drive that must be pressed and slid off the wiper shaft. The hardest part was getting clearence between the engine and wiper motor. If I remember there was a way to turn the wiper case to clear the engine. I have asked myself why this was engineered like this? There is nothing important in the way that 3/4" of clearance could have been given for removal.

May 06, 2009 | 1999 Ford Crown Victoria

Not finding what you are looking for?
1998 Ford Expedition Logo

Related Topics:

82 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

76132 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

fordexpert

Level 3 Expert

5520 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...