Question about 2006 GMC Envoy Xl

2 Answers

Check engine light on and when you put gas in the gas light comes on and the hand doesn't move

Posted by on

2 Answers

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Brigadier General:

    An expert that has over 10,000 points.

  • Master
  • 4,088 Answers

The first thing you need to do is get the trouble codes read out with a scanner and pursue to repairs. The light and gauge are run by the computer, so the above recommendation may fix those problems as well. Look for poor wiring grounding points in the engine compartment and under dash area.

Posted on Oct 08, 2009

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Master
  • 750 Answers

There is some engine fault present and the fuel level sending unit may be stuck in the low position remove an check,vanish from fuel may have build up on float

Posted on Oct 08, 2009

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I used my 2000 kia sephia one night with no problems! The next morning I got in my car started it up like normal! I moved from park to drive and pressed the gas and my car didn't move! When I put it in...


your shifting linkage probably came loose check under your hood if you dont know what it looks like buy a haynes repair manual,they are great help

Jan 15, 2013 | Cars & Trucks

1 Answer

Dashboard power is out


There are at least 4 fuses in the box in the engine compartment that power the cluster.
Have you checked all of the fuses with a test light ?

Aug 28, 2012 | 2003 GMC Yukon XL

1 Answer

92 suburu svx it has wiring gremlins check engin light comes on sometimes but I lf I turn the car off and restart it, then it's gone. And gas gadge doesn't work sometimes come on. And no cruse...


The check engine light will set a code, to read this code you must have the system scanned with a special tool. This is not a wiring GREMLIN, trust me. As far as the gas gauge goes you will need to pull the fuel tank out and replace the gas gauge fuel level sending unit.

Feb 25, 2012 | 1992 Subaru SVX

1 Answer

Car ran fine put gas in it came home shut it off went to leave and it wont start


Does the engine turn over? If it does, then check to see if the check engine light comes on when you turn the key to the on position. If it doesn't, then the PCM is not receiving power. Check the orange power wire usually located by the battery to make sure it isn't damaged. Repair if necessary. If the check engine light comes on when the key is turned to on then crank the engine while observing the light. Does it go out while cranking? If it doesn't, then a problem with the crank sensor signal is indicated. If it does go out then the problem might be fuel related. Disconnect the air cleaner hose to the throttle body. Have someone crank the engine over while opening the throttle slightly. Spray starting fluid into the engine to see if it tries to start. If it does then a fuel related problem is indicated.
CAUTION : Wear safety glasses during this procedure. Be careful around moving engine parts.

May 17, 2011 | 1998 Pontiac Grand Am

1 Answer

I have a 1989 Cadillac brougham and the check engin light comes on when I start it and let it idel but if I start it and put just a very little pressure on the gas peadle it's stays off what does that...


It would be worth checking or changing the air, fuel and oil filters and if that doesn't help try getting the engine codes checked with an obd reader.
Hope this helps.

May 10, 2011 | 1989 Cadillac Brougham

3 Answers

The engine light comes on. When the gas tank is


Most likely an EVAP code. Need to scan it to get the specifics.

Jan 05, 2010 | 2005 Jeep Grand Cherokee

Not finding what you are looking for?
Cars & Trucks Logo

104 people viewed this question

Ask a Question

Usually answered in minutes!

Top GMC Experts

yadayada
yadayada

Level 3 Expert

75005 Answers

Freddy

Level 3 Expert

1311 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Are you a GMC Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...