Question about 2002 Hummer H1

1 Answer

The bolt that holds the seat belt to the car floor is stripped with the plate also? I can't get to the bottom of the plate under the truck to put a longer grade 8 bolt and an aircraft lock nut?

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    President:

    An expert whose answer got voted for 500 times.

  • Master
  • 1,627 Answers

You can drill out the plate and the floor and put in a bolt and nut,useing washers of course.i can't be more specific,i don't know what your vehicle is.

Posted on Oct 08, 2009

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How to replace rear-left seat belt?


un do the bolts that hold the seat belt rewinder
take out the back seat and then undo the bolt that holds seat belt to floor of car then install whole replacement seat belt unit inset and retighten the bolts.
http://www.carparts.com/toyota/camry/seat-belt

Oct 13, 2015 | 2009 Toyota Camry LE

1 Answer

How do I remove the original seat covers from a PT Cruiser driver seat


get under the front seats there are 4 bolts holding the seats in the floor plus a torx bolt for the lap belt, take seats out the back seat has 2 torx bolts at the front bottom of the lower cushion remove them and pull the bottom forward the back has 2 bolts holding it remove them and lift the unit straight up, be carefull there is wires under the front seat for the seat belt warning light carefully unhook them 1 for each seat now you need hog ring plairs and a bunch of new hog rings to secure the new fabric, use side cutter plairs to remove old hog rings carefully remove the seat covers, hog rings can be got at car glass shops the pliars can be got from summit racing or a place that sells car uppolstrytake your time and you can do it!!

Oct 29, 2014 | Chrysler PT Cruiser Cars & Trucks

1 Answer

How do I replace a seat belt?


Under the seat there will be a bolt holding the belt to the floor remove both bolts one for each part on the seat belt then just bolt in the new one`s.

Jun 29, 2014 | 1984 Chevrolet Corvette

2 Answers

I need to know how to take out the bottom of the back seat in my 1998 Buick Skylark so I can install seat covers I just ordered online. I can't figure out how to fold the backrest down either. Please help!


check under the floor mat just under the seat for 2 bolts that hold it down or it may just take a sudden lift up at the front to pull it out of the spring clips holding it down. As to the back bit , when you have the seat out check for 2 bolts under the bottom of the back . remove them and lift the back straight up to unclip from the top.

Apr 21, 2014 | 1998 Buick Skylark

1 Answer

Release retracted seatbelt


You have to unbolt it on the bottom; it is one bolt holding it on the bottom underneath the seat. Once you get it released, it should be fine. You will have to remember to pull some slack out and tie a knot in the belt whenever you fold the seats down.

May 03, 2017 | Volvo C70 Cars & Trucks

3 Answers

Ford Escape middle rear seat belt stuck


Hey everyone--after searching in vain for an entire 10 days, and absolutely REFUSING to pay Ford's $100 diagnosis fee, and their $300 replacement suggestion ($400??), I decided to figure this out myself. And I did. Do the following to let loose the tension that has kept your seat stuck in the down position (though my truck is a 2008 Ford Escape, I have a strong feeling this is the case with any vehicle):

1. Remove the seat bottoms (which are folded forward and upward against the back of the front seats). To do this, find the bars that are bracketed into the floor. There may or may not be a little yellow lever on one of the two brackets. If so, flip it and slide the bar out. If it stops, pull the other side out. Doing this should allow you to completely remove the seat from the car. Repeat with other side.

Now you should have plenty of room to work. Move front seats forward, and you've got even more.

2. Remove your back seats entirely. (Sorry- it's a must.) For many, you will require either one or both of these:
One Torx T-50 socket to remove T-50 bolt (which bolts seat belt latches to the floor)
One Torx T-55 (which bolts the folding seat into the bracket that bolts seats to the floor).
One socket extension (tip: the extension gives you much more torque, and its easier to remove bolts) and
One a 5/8" socket. (See continuation after following tip.)

TIP: if you have a 40/60 split, you have to remove the 40 first! This will allow you room to move around the 60 seat and its stuck belt.

Continued:
Remove bolts that bolt bracket to car floor (this is the 40 seat). I believe there's two: 1 directly below the seat, and 1 that also bolts the 60 seat (you'll be using the 5/8" here)-- Don't hold me to it, though, as I've seen some different stuff. Pull seat out of the way to avoid potential damage. NOTE: THOSE BRACKETS ARE SHARP. WATCH THE LEATHER/SEAT MATERIAL-- AND YOUR HANDS.)

2. Remove bolts on the 60. Though the top part of your seat is down, you should be able to the bolt that keeps the bracket to the floor beneath where the seat cushion would be (and where the upper part of the seat is laying flat). A ratchet would probably be best for this since you can keep the socket in place and wind the thing completely out. I should say here that my seat couldn't have been tighter to the floor. If I got mine out, I'm sure you can, too.

Now here come the tricky, but verrrrry easy parts. They are vital.

1. Now that the brackets are off of the floor, the 60 seat should now be free-floating in your hands, but tethered by the T50 bolt that is keeping the seatbelt buckle to the floor. Remove it. Now you should be able to remove the seat altogether. I had to bring mine inside where it wasn't 15 degrees in my garage, but I believe you'll do these parts in the next five minutes. Do this next:

2. TIP the 60 SEAT UPRIGHT (just like it would if things were back to the normal operational mode). This is VITAL. If you cannot fix it with two or three tugs from here (don't waste more time than this-- the final part is coming), then do this next:

3. Find the latch on the back of the seat that locks onto the latch of the car. Using two gloved fingers (or tools), press the latch inward until it's in the LOCKED position (fooling it into thinking you've put it up and latched into into the truck bracket).
This should have also reset the button or lever that you used to unlock the seat in the first place. Now give your belt a tug. It should come loose like normal.

IMPORTANT NOTE: seatbelt tensioners rely on gravity (thing momentum during a crash) that locks the belt. If the seat is not sitting UPRIGHT (like in normal use mode), that mechanism is going to obey gravity if it is tilted backward or forward (which is why the seat got in the downward position to begin with) and lock.

That's it. Bolt the seats back in, and go buy yourself $400 worth of rewards.

Oct 31, 2010 | 2008 Ford Escape

1 Answer

How to fix a stuck seat belt VW GTI 2009


I just solved the problem for a stuck rear center seat belt in my 2002 Jetta.

Flip the base seat cushion forward against the front seat backs. Trace down along the belt to its tether point on the floor. The belt is sewn around a steel loop. The loop is anchored to a black steel hook. A thin silvery retainer plate is spring tensioned on top of the loop to prevent it from sliding off of the hook when the seat back is folded.

Therefore, you need to press the silvery retainer plate away from the hook (push up) to allow the loop to be slid from the hook. The belt was tight with the seat back in the upright position, so it was necessary to fold the seat back forward to create slack in the belt. Now push the belt loop towards the trunk and slide it off of the end of the hook (only possible with the retainer plate pushed up out of the way).

Now with total release of tension on the system via the bottom end of the seat belt being untethered and with the seat back returned to the upright position, normal extension and retraction of the belt will be reestablished. Next, simply extend the seat belt and slide the loop back into place over the floor hook. It snaps past the silvery retainer plate without all the effort required to hold the plate up during removal of the loop during disassembly.

Check again, the seat belt should be extending and retracting properly. Now just put the seat cushion back into regular position and you will be able to safely buckle up three people across the back seat.

It took about as long to do this repair as it has taken to post this answer to the problem. Note, the seat belt safety mechanism only allows normal extension and retraction of the belt when the seat back is upright.

Nov 29, 2009 | Volkswagen GTI Cars & Trucks

1 Answer

HOw to get into engine to change spug pluggs and leads for Toyota estima 1993


The best thing to do is to purchase a Haynes manual for the Toyota Previa. But to access the spark plug wires and spark plugs you will need to remove the passenger front seat. This requires taking out four bolts on the four corners of the seat. After the seat is removed you need to remove the outside seat support and the jack and jack handle that is located under the seat. Next remove the bolt from the seat belt/shoulder harness. Romove the screws from the side of the carpet keeper strip along the bottom of the door. carefully, using a flat blade screwdriver, pry the plastic carpet strip up carefully disengaging it from the rear strip. Unhook the carpet from the edge of the doorway. Pull the carpet back enough to expose the bolts holding the cover over the engine. Remove all the bolts holding the cover over the engine. This will expose the engine head. remove the three bots holding the black plastic cover over the spark plug wires. This wires can be removed allowing access to the plugs. Be aware these engines use only platinum tipped spark plugs. Good Luck

Nov 21, 2008 | 1993 Toyota Previa

1 Answer

Seat Belt repair/replace


  1. Remove front seat.
  2. Remove adjuster cover. A
  3. Slide floor anchor cover.
  4. Remove floor anchor bolt. B
  5. Remove shoulder anchor bolt. C
  6. Remove front and rear kicking plate, then remove center pillar upper and lower garnish.
  7. Disconnect seat belt pre-tensioner connector.
  8. Remove the screw securing seat belt pre-tensioner retractor, then remove seat belt and seat belt pre-tensioner retractor.
  9. Remove bolts securing seat belt adjuster, then remove seat belt adjuster. Reverse procedure to install.J

Nov 03, 2008 | 2000 Nissan Maxima

1 Answer

My rear seat belts have locked with the seat in the down position and i can not put the seat back up


I had a problem like this. The seat belt stop (the small button through the belt) had broken and fallen off. When I tried put the seat up the belt had wound too tight and with no slack wouldn't release. I had to unbolt the bottom end of the seat belt from the floor and raise the seat. While I had the unit off the floor I had slack enough to release the belt and extend it to bolt the floor unit back down. There should be two of these button on the belt. One keeps the belt from rewinding too far and the other one holds the seat belt latch up on the belt. You can buy these buttons from some auto parts stores. You might have to buy a bag full, but they're not expensive. Good luck..

Aug 12, 2008 | 2001 Volvo V70

Not finding what you are looking for?
2002 Hummer H1 Logo

Related Topics:

51 people viewed this question

Ask a Question

Usually answered in minutes!

Top Hummer Experts

yadayada
yadayada

Level 3 Expert

76649 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8522 Answers

Are you a Hummer Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...