Question about 2000 Chevrolet Silverado 1500

1 Answer

Need diagram for front cv halfshaft - 2000 Chevrolet Silverado 1500

Posted by on

Ad

1 Answer

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 1 Answer

I can not take apart my old half shaft on a 94' chevy 1500k all i need is some kind of exploded view to see how its done i have never done this before

Posted on Nov 15, 2009

Ad

2 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
  • 70 Answers

SOURCE: 1991 corolla makes a clank sound from the pass

check the bushes

Posted on Apr 02, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

4wd. How can I replace CV joint?


Hi Terez,here's a repair guide from Autozone site,join their site,it's free,then you can use all their repair guides like me,I will send you 2 links for your CV joint replacement guide,here's the first one. Repair Guides Front Drive Axle Halfshafts AutoZone com Here's the second link. Repair Guides Front Drive Axle Cv joints AutoZone com Here's another link to your locking hubs. Repair Guides Front Drive Axle Locking Hubs AutoZone com

Feb 09, 2016 | 2001 Kia Sportage

1 Answer

Mazda axle shaft


not anymore than any other front wheel drive car. are you having a noise(clicking or clunking) coming from the front only when turning. if so then you have a bad cv joint on the axle. its cheaper to replace the entire halfshaft(axle) than just the bad joint, as you get a rebuilt halfshaft complete. if you hear the noise when turning left then the left halfshaft is bad if you hear it only when you turn right then the right side is bad. you don`t say what issue you are having.

May 25, 2014 | 2008 Mazda 6 2.0

2 Answers

On my 97 the abs ring on the cv axle is almost gone!! made a turn today and the wheel almost locked up..any help??


I would have the cv axle changed along with any integral parts such as the abs ring.

REMOVAL & INSTALLATION
  1. Disconnect the negative battery cable.
  2. Remove the wheel cover/hub cover from the wheel and tire assembly, then loosen the lug nuts. Fig. 1: After removing the wheel/hub cover, loosen the lug nuts 86877115.gif

  3. Raise and safely support the vehicle, then remove the wheel and tire assembly. Insert a steel rod in the rotor to prevent it from turning, then remove the hub nut and washer. Discard the old hub nut. Fig. 2: Before removing the hub nut and washer, insert a steel rod in the rotor to prevent it from turning 86877116.gif
    Fig. 3: Remove the hub nut and washer, then discard the nut, and replace with a new one during installation 86877117.gif

  4. Remove the nut from the ball joint to steering knuckle attaching bolts.
  5. Drive the bolt out of the steering knuckle using a punch and hammer. Discard this bolt and nut after removal. Fig. 4: Drive the bolt out of the front wheel knuckle using a punch and hammer, then discard the nut and bolt and replace with new ones during installation 86877118.gif

  6. If equipped with anti-lock brakes, remove the anti-lock brake sensor and position it aside. If equipped with air suspension, remove the height sensor bracket retaining bolt and wire sensor bracket to inner fender. Position the sensor link aside. Fig. 5: If so equipped, remove the anti-lock brake sensor and position it aside 86877119.gif

  7. Separate the ball joint from the steering knuckle using a suitable prybar. Position the end of the prybar outside of the bushing pocket to avoid damage to the bushing. Use care to prevent damage to the ball joint boot. Remove the stabilizer bar link at the stabilizer bar. Fig. 6: When separating the ball joint from the steering knuckle, be careful not to damage to ball joint boot 86877120.gif
    1. Slide the link shaft out of the transaxle. Support the end of the shaft by suspending it from a convenient underbody component with a piece of wire. Do not allow the shaft to hang unsupported, damage to the outboard CV-joint may occur.
    2. Separate the outboard CV-joint from the hub using front hub remover tool T81P-1104-C or equivalent and metric adapter tools T83P-1104-BH, T86P-1104-Al and T81P-1104-A or equivalent. NOTE: Never use a hammer to separate the outboard CV-joint stub shaft from the hub. Damage to the CV-joint threads and internal components may result. The halfshaft assembly is removed as a complete unit.
    3. Install the CV-joint puller tool T86P-3514-A1 or equivalent, between CV-joint and transaxle case. Turn the steering hub and/or wire strut assembly aside.
    4. Screw extension tool T86P-3514-A2 or equivalent, into the CV-joint puller and hand tighten. Screw an impact slide hammer onto the extension and remove the CV-joint.
    5. Support the end of the shaft by suspending it from a convenient underbody component with a piece of wire. Do not allow the shaft to hang unsupported, damage to the outboard CV-joint may occur.
    6. Separate the outboard CV-joint from the hub using front hub remover tool T81P-1104-C or equivalent and metric adapter tools T83P-1104-BH, T86P-1104-Al and T81P-1104-A or equivalent.
    7. Remove the halfshaft assembly from the vehicle. Fig. 7: These tools are necessary for halfshaft removal 86877121.gif
      Fig. 8: Installing the specified tools to remove the halfshaft assembly from the vehicle 86877122.gif
      Fig. 9: Support the end of the shaft by suspending it from a convenient underbody component with a piece of wire. Do not allow the shaft to hang unsupported, since damage to the outboard CV-joint may occur 86877123.gif
      Fig. 10: Separate the outboard CV-joint from the hub using front hub remover tool T81P-1104-C or equivalent, and metric adapter tools T83P-1104-BH, T86P-1104-Al and T81P-1104-A or equivalent, then remove the halfshaft assembly from the vehicle 86877124.gif
      Fig. 11: Exploded view of the halfshaft assemblies and related components - automatic transaxle 86877125.gif
prev.gif next.gif

Oct 26, 2010 | 1997 Lincoln Continental

1 Answer

Removal of front right axle from a jaguar 2002 x-type


Loosen the wheel hub nut.
Remove the front road wheel and tire.
Remove the tie rod end retaining nut.
Using the special tool 204-192 Ball joint Splitter
detach the tie rod end.
Remove the subframe reinforcement plate retaining bolts.
Loosen the subframe rear mount bolt.
Loosen the subframe front mount bolt.
Remove and discard the wheel hub nut.
using spcial tools 204-269Forcing Screw,205-491-01 adapter nuts,205-491 wheel hub puller
Detach the wheel knuckle.
Remove the lower arm ball joint retaining bolt.
Reposition the lower arm.
Detach the wheel knuckle.
using special tools 307-443 RH Halfshaft splitter ,307-442 RH Halfshaft splitter handle
detach the halfshaft.
Remove the exhaust muffler inlet pipe.
Remove the halfshaft seal.
Remove the transfer case Y bracket retaining bolt.
To prevent damage to the transfer box internal seal,
make sure that the link shaft is not retracted further than
200 mm from the transfer box casing.
remove the halfshaft.
Attach special tools to the halfshaft.
Lever the special tools to displace the halfshaft.
Install the transfer case Y bracket retaining bolt.
Remove the halfshaft.
Use suitable protective covers to protect the barshaft.
Remove the halfshaft snap ring.
Install a new snap ring to the halfshaft.
Install a new halfshaft seal.
Remove the special tool.
Remove the transfer case Y bracket retaining bolt.
Remove the special tool.
Make sure the CV joint splines are located fully.
Do not use excessive force when engaging the CV joint into the link shaft.
Install the halfshaft.
Install the transfer case Y bracket retaining bolt.
Tighten to 25 Nm.
Attach the wheel knuckle.
Reposition the lower arm.
Attach the wheel knuckle.
Install the lower arm ball joint retaining bolt.
Tighten to 83 Nm.
Install the exhaust muffler inlet pipe.
Tighten the subframe front mount retaining bolt.
Tighten to 142 Nm.
Loosely install the subframe rear mount retaining bolt.
Install the subframe reinforcement plate retaining bolts.
Tighten to 35 Nm. Tighten to 142 Nm.
Install the tie rod end.
Tighten to 35 Nm.
Loosely install a new wheel hub nut.
Install the front road wheel and tire.
Tighten the wheel hub nut.
Tighten to 330 Nm.
Check the subframe alignment.

May 20, 2010 | 2002 Jaguar X-Type

2 Answers

STEARING SEAMS TO BE STIFFER AND SHAKING COMING THROUGH THE STEARING WHEEL AND WHEN YOU APLAY THE BREAKS YOU CAN FEEL BUMPING THROUGH THE BREAK PEDAL AND ALSO FLIKEREING ON THE SPEEDO


you may have bad CV joints. Each halfshaft has an inner and outer cv joint. One halfshaft going to each front wheel. Check to see if the rubber boots are split and all the grease leaked out.

May 21, 2010 | 1994 Ford Escort

1 Answer

Describe your replace front passenger side cv joint 1998 4wd chevy silverado 1500 Problem my front passenger side cv joint is making extremely loud noise, especially while turning. How much can I expect...


CV halfshaft will run you $75 at local autoparts store. Shop labor varies from shop to shop as well as their expertise.
The brake caliper has to be pulled, lower shock bolt removed, upper and lower ball joint seperated (book will say only one but it is not true) and steering knuckle and axle nut removed. CV joint simply unbolts at differential output flange.

Apr 19, 2010 | 1999 Chevrolet Silverado 1500

1 Answer

Do I have to remove the control arm to replace the half shaft on a 2005 Ford Freestar?


no, here's the procedure for 2002 windstar, should be similar. please rate, thanks.

NOTE: This procedure applies to both the LH and RH halfshaft assemblies.
  1. Raise and support the vehicle. For additional information, refer to Section 100-02 .
  1. Remove the front wheel and tire assembly. For additional information, refer to Section 204-04 .
  1. Insert a steel rod in the brake disc to prevent the halfshaft from turning while removing the front axle wheel end nut.
  1. s2w~us~en~file=ani_caut.gif~gen~ref.gif CAUTION: The front axle wheel end nut is a torque prevailing design nut. Do not reuse it.
    Remove the nut and washer.
    • Remove the steel rod in the brake disc.
  1. s2w~us~en~file=ani_caut.gif~gen~ref.gif WARNING: Remove or tape the brake pads to prevent them from falling out of the anchor plate.
    s2w~us~en~file=ani_caut.gif~gen~ref.gif CAUTION: To prevent damage to the brake hose, do not allow the disc brake caliper to hang suspended from the hose.
    Remove the bolts and position the disc brake caliper aside.
  1. Remove the front brake anti-lock sensor harness from the clip.
  1. Remove and discard the nut and bolt.
    • If necessary, use a punch and a hammer to drive the bolt out of the knuckle.
  1. s2w~us~en~file=ani_caut.gif~gen~ref.gif CAUTION: Position the end of the pry bar outside the bushing pocket to avoid damage to the bushing.
    s2w~us~en~file=ani_caut.gif~gen~ref.gif CAUTION: Do not damage the front wheel driveshaft joint boot (3A331).
    Separate the front suspension lower arm from the knuckle.
  1. s2w~us~en~file=ani_caut.gif~gen~ref.gif CAUTION: Never use a hammer to separate the front wheel driveshaft joint (3B413) from the wheel hub. Damage to the joint threads and internal components can result.
    Using the special tool, press on the front wheel driveshaft joint until it is loose in the wheel hub.
  1. Rotate the front wheel knuckle rearward, while pulling it outward at the bottom and remove the front wheel driveshaft joint from the wheel hub.
  1. Using a pry bar, separate the inboard CV joint housing assembly (3B436) (3B437) from the transaxle.
  1. s2w~us~en~file=ani_caut.gif~gen~ref.gif CAUTION: Do not damage the differential seal.
    Remove the halfshaft assembly with both hands.
Installation
  1. Lubricate the differential seal.
    • Use MERCON® V Automatic Transmission Fluid XT-5-QM or equivalent meeting MERCON® V specifications.
  1. s2w~us~en~file=ani_caut.gif~gen~ref.gif CAUTION: Install a new circlip every time you remove the halfshaft from the vehicle.
    On the RH side halfshaft only, install a new circlip in the groove in the inboard CV joint stub shaft.
    • Start one end in the groove and work the circlip over the shaft and into the groove. This will prevent the circlip from over-expanding.
  1. s2w~us~en~file=ani_caut.gif~gen~ref.gif CAUTION: Do not damage the inboard CV joint housing assembly and the differential seal.
    NOTE: If necessary, use a non-metallic mallet to aid in seating the circlip in the differential side gear groove (RH) or inboard CV joint housing (LH). Tap only on the outboard front wheel driveshaft joint.
    Align the inboard CV joint housing splines with the differential side gear splines (RH) or output shaft splines (LH), and push the inboard CV joint housing assembly inward until the circlip seats in the differential side gear (RH) or inboard CV joint housing (LH).
  1. Align the front wheel driveshaft joint splines and the wheel hub splines, and push the joint into the wheel hub as far as possible.
  1. Install the washer and the old nut. Using the old nut, seat the front wheel driveshaft joint in the hub. Remove the old nut and discard it.
  1. Connect the suspension lower arm to the knuckle.
  1. s2w~us~en~file=ani_caut.gif~gen~ref.gif CAUTION: Install a new bolt and nut.
    Install the new bolt and nut.
  1. Insert a steel rod in the brake disc to prevent the halfshaft from turning while installing the new front axle wheel end nut.
  1. Apply a small patch of Loctite 242 or equivalent meeting Ford specification WSK-M2G351-A5 to the last five front wheel driveshaft joint threads.
  1. s2w~us~en~file=ani_caut.gif~gen~ref.gif CAUTION: Install and tighten the new front axle wheel end nut to specification in a continuous rotation. Stopping the rotation during installation will cause the nylon lock to set incorrectly. This will cause incorrect torque readings while tightening the nut, and lead to bearing failure. Always install a new front axle wheel end nut after loosening the nut, or when the nut has not been installed to specification in a continuous rotation.
    Install and tighten the new nut to specification in a continuous rotation.
    • Remove the steel rod from the brake disc.
  1. Position the disc brake caliper and install the bolts.
  1. Install the front brake anti-lock sensor harness in the clip.
  1. Install the wheel and tire assembly. For additional information, refer to Section 204-04 .
  1. Lower the vehicle.
  1. Check and, if necessary, fill the transaxle to the correct level with the specified fluid. For additional information, refer to Section 307-01 .

Nov 15, 2009 | 2005 Ford Freestar

1 Answer

Bad right rear axle. Need to know how to replace axle.


Dana or Ford axle?

Ford here:
SECTION 205-05: Rear Drive Halfshafts 2002 Explorer/Mountaineer Workshop Manual
REMOVAL AND INSTALLATION Halfshaft
Special Tool(s) s2n~us~en~file=st2258a.gif~gen~ref.gif Protector, Differential Seal
205-506 s2n~us~en~file=st2272a.gif~gen~ref.gif Remover, Front Wheel Hub
205-D070 (D93P-1175-B) or equivalent s2n~us~en~file=st2309a.gif~gen~ref.gif Remover, Halfshaft
205-502
Removal and Installation
NOTE: This procedure applies to both rear halfshaft assemblies.
  1. s2n~us~en~file=ani_caut.gif~gen~ref.gif CAUTION: Do not loosen the rear axle wheel hub retainer until after the wheel and tire assembly are removed from the vehicle. Wheel bearing damage will occur if the wheel bearing is unloaded with the weight of the vehicle applied.
    With the vehicle in NEUTRAL, raise and support the vehicle. For additional information, refer to Section 100-02 .
  1. Remove the rear wheel and tire assembly. For additional information, refer to Section 204-04 .
  1. NOTE: Have an assistant press the brake pedal to keep the axle from rotating.
    Remove and discard the rear axle wheel hub retainer and the washer.
  1. s2n~us~en~file=ani_caut.gif~gen~ref.gif CAUTION: To prevent damage to the brake hose, do not allow the disc brake caliper to hang suspended from the hose.
    Remove the brake disc.
    1. Remove the two bolts and lift the disc brake caliper and brake pads off the brake disc.
      • Using mechanics wire, position the disc brake caliper out of the way.
    1. Remove the brake disc.
  1. Remove the bolt retaining the parking brake cable bracket to the frame.
  1. s2n~us~en~file=ani_caut.gif~gen~ref.gif CAUTION: Cover the stabilizer link bolt threads and the nut to prevent boot damage when removing the halfshaft assembly from the vehicle.
    Using a rubber hose approximately 37.5 mm (1.5 in) long, cover the stabilizer link bolt threads and nut.
  1. s2n~us~en~file=ani_caut.gif~gen~ref.gif WARNING: The bolt that retains the upper ball joint to the knuckle is longer and it has fewer threads than the bolt that retains the toe link to the knuckle. Switching these bolts during installation will prevent the pinch arms on the knuckle from correctly retaining the toe link to the knuckle. This may cause the toe link to separate from the knuckle during vehicle operation. Failure to follow these instructions may result in personal injury.
    Remove the pinch bolts and disconnect the toe link and upper ball joint from the knuckle.
  1. s2n~us~en~file=ani_caut.gif~gen~ref.gif CAUTION: Support the rear suspension upper arm to prevent boot damage when removing the halfshaft assembly from the vehicle.
    Using a wood stick, approximately 450 mm (18 in) long and 25 mm (1 in) wide, support the rear suspension upper arm.
  1. s2n~us~en~file=ani_caut.gif~gen~ref.gif CAUTION: Do not use a hammer to separate the outboard CV joint from the hub. Damage to the threads and internal CV joint components may result.
    s2n~us~en~file=ani_caut.gif~gen~ref.gif CAUTION: Once the outboard CV joint separates from the hub the knuckle will continue to pivot until the brake backing plate presses against the suspension lower arm. To prevent damage to the brake backing plate, immediately after separating the outboard CV joint from the hub, rest the knuckle on a cushioned support that is tall enough to keep the backing plate from pressing against the suspension lower arm.
    Separate the outboard CV joint from the hub and rest the knuckle on a cushioned support.
    1. Using the special tool, press the outboard CV joint until it is loose in the hub.
    1. Remove the special tool.
    1. Separate the outboard CV joint from the hub.
    1. Rest the knuckle on a cushioned support.
04ab306.gif
  1. s2n~us~en~file=ani_caut.gif~gen~ref.gif CAUTION: Do not damage the axle shaft oil seal or the machined sealing surface on the inboard CV joint housing.
    s2n~us~en~file=ani_caut.gif~gen~ref.gif CAUTION: Do not allow the splines on inboard CV joint housing to touch the axle shaft oil seal.
    NOTE: A circlip retains the inboard CV joint housing to the differential side gear in the axle.
    Using the special tool, disengage the inboard CV joint housing from the differential side gear.
c231bc2.gif
  1. s2n~us~en~file=ani_caut.gif~gen~ref.gif CAUTION: To prevent damage to the axle shaft oil seal, install the special tool before removing the inboard CV joint housing from the axle.
    Install the special tool.
50c5d1d.gif
  1. Remove the halfshaft assembly from the vehicle.
  1. s2n~us~en~file=ani_caut.gif~gen~ref.gif CAUTION: To prevent damage to the axle shaft oil seal, install the Differential Seal Protector before positioning the inboard CV joint housing in the axle.
    s2n~us~en~file=ani_caut.gif~gen~ref.gif CAUTION: Always install the halfshaft with a new retainer circlip and a new rear axle wheel hub retainer.
    s2n~us~en~file=ani_caut.gif~gen~ref.gif CAUTION: Never use power tools to tighten the rear axle wheel hub retainer.
    To install, reverse the removal procedure.

Apr 17, 2009 | Ford Explorer Cars & Trucks

2 Answers

Cv joint on 1990 mazda 626 drivers side


NOT THAT HARD A JOB JACK UP PUT STANDS UNDER FOR YOUR OWN SAFETY UNBOLT CV AROUND 5 BOLTS ON EACH END WITH SOCKET REMOVE BOLTS WITH CAR IN FIRST GEAR OR PARK THEN PUT IN NEUTRAL TO MOVE CV BOLTS AROUND SO THEY ARE EASIER TO GET TO ONCE REMOVED REPLACE WITH NEW ONE AFTER 100KMS CHECK THAT BOLTS ARE STILL TIGHT A SMALL TIP IF REPLACING ONE CV DUE TO WEAR ALSO REPLACE THE OTHER ONE AS WELL AND THERE IS A PRODUCT MADE BY LOCKTITE THAT YOU PUT ON THE NEW BOLTS TO STOP THEM FROM COMING LOOSE WHILE DRIVING PS THE BOLTS WILL BE TIGHT PUT A PIECE OF HOLLOW PIPE ABOUT2 FOOT LONG OVER END OF SOCKET HANDLE FOR HEAPS MORE POWER HOPE THIS IS HELPFUL GLENN........

Nov 15, 2008 | Hyundai Motor 1999 Elantra

Not finding what you are looking for?
Cars & Trucks Logo

473 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts

yadayada
yadayada

Level 3 Expert

76846 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22246 Answers

Ronny Bennett Sr.
Ronny Bennett Sr.

Level 3 Expert

6924 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...