Question about 1992 Isuzu Rodeo

Open Question

I needed change cv axle drive side isuzu rodeo 98

Posted by on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
  • 13 Answers

SOURCE: having problem pulling cv axle

the front axle assy. is basically the same as the older ones. but....u can remove the hub....and spindle assy.....cut the big clamp on the inner boot.....im assuming your replacing boot kits.....pull boot back and slip small screw driver in there....there is a large this round low tension c lip in there.....then u can pull outer joint and axle and most of inner joint......replace the boots......fill inner boot with grease and reassemble.....time consuming but not real bad to do.

Posted on Feb 15, 2009

Ad
germcelchar
  • 389 Answers

SOURCE: how do i remove cv axle for a 98 isuzu trooper

Go to my profile I have just explained how to change a cv boot on a Trooper. The axle needs to be taken out to change the boot so the same solution. What you call an axle I have refered to as a drive (short for driveshaft) It takes a lot of explaining so save me a lot of writing if you read the solution I gave for changing the CV boot. Cheer's

Posted on Sep 28, 2009

honeymokey
  • 3113 Answers

SOURCE: I have a 1999 isuzu 4wd rodeo 6 cylinder and was

Do not try to get the cv axle out ot the axle housing. It is a major operation. Remove boot and disconnect the inner cv joint and save about five hours of time. The choice is yours ,boot or reman cv axle. You will need to take the reman. axle apart to install it though and some new clamps. Not a simple operation.

Posted on Oct 10, 2009

BCAS1298
  • 3092 Answers

SOURCE: Do I have to remove 4 bolts around axle to replace

Yes

Posted on Dec 13, 2009

  • 25 Answers

SOURCE: '93 Isuzu Rodeo, CV Joint replacement.

unbolt the tie rod end and the lower a arm and it should slide out of there

Posted on Feb 26, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How to get the CV axle for a 1998 Isuzu rodeo


THERE ARE PLENTY AVAILABLE FROM SCRAP YARDS, AND E-BAY. THE RODEO HAD PROBLEMS WITH THE TRANSMISSION.

Jun 20, 2015 | 1998 Isuzu Rodeo

1 Answer

Isuzu rodeo troubleshooting


Sounds like a ball joint seeing that the cv joints were replaced, have you had it aligned?

May 07, 2014 | 1998 Isuzu Rodeo

1 Answer

Im replacin the cv joints on passanger side and driver side how do i get the axle out of the transmission casing is ther a key behind the plate with the 4 bolts? my truck is a 99 isuzu rodeo LS 4wd


remove inner cv boot, just on inside edge is circlip which holds inner bearing joint into outer housing remove circlip and separate joint outer housing does not come out of front diff unless you drop or remove whole front diff assembly
will have to remove whole stub axle hub assembly to remove drive shaft from outer wheel stub axle (hub) assembly

Apr 20, 2011 | 1999 Isuzu Rodeo

1 Answer

I have a 1999 isuzu 4wd rodeo 6 cylinder and was wondering if Need to install a new boot kit or if I need to replace the entire front left cv axle shaft. I had a tear in my rubber boot and noted some...


Do not try to get the cv axle out ot the axle housing. It is a major operation. Remove boot and disconnect the inner cv joint and save about five hours of time. The choice is yours ,boot or reman cv axle. You will need to take the reman. axle apart to install it though and some new clamps. Not a simple operation.

Sep 28, 2009 | 1997 Isuzu Rodeo

2 Answers

How do i remove cv axle for a 98 isuzu trooper


Go to my profile I have just explained how to change a cv boot on a Trooper. The axle needs to be taken out to change the boot so the same solution. What you call an axle I have refered to as a drive (short for driveshaft) It takes a lot of explaining so save me a lot of writing if you read the solution I gave for changing the CV boot. Cheer's

Sep 27, 2009 | 1998 Isuzu Trooper

3 Answers

How to replace front cv shafts on a 1997 isuzu rodeo ?


Remove tire, remove axle nut, pop ball joint off, remove clip, pull axle

For a more detailed instructions, go to autozone.com and register for free.
Now you will have full free online repair manual

Aug 01, 2009 | 1997 Isuzu Rodeo

1 Answer

Cv joint removal


Get the replacement cv axle and remove inner boot and clip and bearings. Do the same on the old axle. Replace bearing clip, cv shaft and reassemble. Do not try to remove the part from inside the front axle unless you want to spend about six hours of time and money.

May 12, 2009 | 1999 Isuzu Rodeo

1 Answer

1994 cv axle


please go to an auto parts store and buy the auto manual for this car.its not that hard to do.and be careful

Apr 09, 2009 | 2001 Isuzu Rodeo

Not finding what you are looking for?
1992 Isuzu Rodeo Logo

Related Topics:

277 people viewed this question

Ask a Question

Usually answered in minutes!

Top Isuzu Experts

yadayada
yadayada

Level 3 Expert

76846 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22246 Answers

Thomas Perkins
Thomas Perkins

Level 3 Expert

14384 Answers

Are you an Isuzu Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...