Question about 1991 Jeep Wrangler

3 Answers

Overheating jeep wraNGLER 1991 4.0

Overheating jeep wrangler1991 4.0

Posted by on

Ad

3 Answers

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Jeep Master
  • 2,359 Answers

When the car is completely cool,check the electric fan(s) for smooth rotation.

Clean/check/change the thermo sensor,contact and wire.

===

Excavate air pocket in coolant system / check for head gasket leak

This test will kill two birds with one stone.

===

MAKE SURE THE COOLANT SYSTEM and ENGINE IS COLD!

RAN THIS TEST IN A WELL VENTILATED AREA ONLY!

You will spill some coolant during this air pocket purge test.......BE KIND TO THE ENVIRONMENT and ANIMAL please clean up after the test!

===

Put the front end on a pair of ramp or park your car on a VERY STEEP HILL (radiator facing top of the hill) .

Top of the coolant reserve tank

Let it ran for 10-15 minutes.

Monitor for air pockets escaping from coolant reserve tank.

Small amount of bubbles is OK at 1-5 minute mark

After the thermostat open up (after 195 F warm up) at
5-12 minute mark or after high idle you should see less bubbles.

If you do not see any in rush of bubbles then your thermostat may be partially stuck or rusted badly inside the thermostat hosing.

Give the thermostat host few gentle taps.

If you see larger bubbles surfacing after 15 minutes then should do a hydrocarbon (HC) dye test to test for potential head gasket leak.

Let engine cold down and top off coolant reserve tank.

Start monitor for coolant lost

===

A coolant flush is require every 2 years or 24,000 miles.

I recommend the thermostat that has a relief pop-let to reduce the change of burst radiator and coolant hoses.

Make sure you get a new thermostat gasket,black RTV and fresh coolant for the job.

===
Please post more information by clicking the comment link on the top right corner.

DON'T FORGET to RATE ME if my tip is helpful to you!

Posted on Dec 05, 2009

Ad
  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Jeep Master
  • 2,984 Answers

Couple of things it could be:

1. The easiest-thermostat
2. the water pump
3. radiator fan/clutch
4. plugged radiator


Start with squeezing the supply hose at the water pump with the engine running. You should feel flow/pressure.

Posted on Oct 07, 2009

Ad
  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Master
  • 6,784 Answers

The engine is kept cool by a liquid circulating through the engine to a radiator. In the radiator, the liquid is cooled by air passing through the radiator tubes. The coolant is circulated by a rotating water pump driven by the engine crankshaft. The complete engine cooling system consists of a radiator, recovery system, cooling fan, thermostat, water pump and serpentine belt.

Check the coolant level in the recovery bottle or surge tank, usually mounted on the inner fender. With the engine cold, the coolant level should be at the FULL COLD or between the FULL HOT and ADD level. With the engine at normal operating temperature, the coolant level should be at the FULL HOT or HOT mark. Only add coolant to the recovery bottle or surge tank as necessary to bring the system up to a proper level. On any vehicle that is not equipped with a coolant recovery bottle or surge tank, the level must be checked by removing the radiator cap. This should only be done when the cooling system has had time to sufficiently cool after the engine has been run. The coolant level should be within 2 in. (51mm) of the base of the radiator filler neck. If necessary, coolant can then be added directly to the radiator.

While you are checking the coolant level, check the radiator cap for a worn or cracked gasket. If the cap doesn't seal properly, fluid will be lost and the engine will overheat.

Worn caps should be replaced with a new one.

Periodically clean any debris; leaves, paper, insects, etc. from the radiator fins. Pick the large pieces off by hand. The smaller pieces can be washed away with water pressure from a hose.

Carefully straighten any bent radiator fins with a pair of needle nose pliers. Be careful, the fins are very soft. Don't wiggle the fins back and forth too much. Straighten them once and try not move them again. It is recommended that the radiator be cleaned and flushed of sludge and any rust build-up once a year. If this has not been administered within the stated time, this may be why your vehicle is overheating at this time. Have the Radiator flushed asap if this is the case.

Now, if the coolant level is proper and, the cap is in fair or good condition, i would advise to move in the direction of the cooling fans and sensors as well. These fans are vital to the cooling process as well. The cooling fans must cycle in intervals to keep the coolant cool during stop and go driving or, long idle. They are also very important during the operational period of the AC during travel as well. i recommend inspecting the cooling fans while the engine is running. they should cycle during the running period. if thsi is not the case, you will need to test the operational value of these devices. The test procedure follows below


TESTING


1. If the fan doesn't operate, disconnect the fan and apply voltage across the fan terminals. If the fan still doesn't run, it needs a new motor.

2. If the fan runs, with the jumpers but not when connected, the fan relay is the most likely problem.

3. If fan operates but a high current draw is suspected continue with the following ammeter TESTING.

4. Disconnect the electrical connector from the cooling fan.

5. Using an ammeter and jumper wires, connect the fan motor in series with the battery and ammeter. With the fan running, check the ammeter reading, it should be 3.4-5.0 amps; if not, replace the motor.

6. Reconnect the fan's electrical connector. Start the engine, allow it to reach temperatures above 194°F and confirm that the fan runs. If the fan doesn't run, replace the temperature switch.



Ok, Now we will move on to the next possible issue. The water pump. ok, due to the fact that your pump is driven by the drive belt, you will need to start the engine and listen for bad bearing, using a mechanic's Stethoscope or rubber tubing.

* Place the stethoscope or hose on the bearing or pump shaft.
* If a louder than normal noise is heard, the bearing is defective.

Replace the pump in this case.

You will also notice leakage around the pump housing if the seal has failed as well. this will strain the impeller and, ruin the pump.

Now. the last area of concern will be the thermosta. this is the most common issue that will inflict overheating in many vehicles. The thermostat is used to control the flow of engine coolant. When the engine is cold, the thermostat is closed to prevent coolant from circulating through the engine. As the engine begins to warm up, the thermostat opens to allow the coolant to flow through the radiator and cool the engine to its normal operating temperature. Fuel economy and engine durability is increased when operated at normal operating temperature.


There are several ways to test the opening temperature of a thermostat.

One method does not require that the thermostat be removed from the engine.

* Remove the radiator pressure cap from a cool radiator and insert a thermometer into the coolant.
* Start the engine and let it warm up. Watch the thermometer and the surface of the coolant.
* When the coolant begins to flow, this indicates the thermostat has started to open.
* The reading on the thermometer indicates the opening temperature of the thermostat.
* If the engine is cold and coolant circulates, this indicates the thermostat is stuck open and must be replaced.

The other way to test a thermostat is to remove it.

* Suspend the thermostat completely submerged in a small container of water so it does not touch the bottom.
* Place a thermometer in the water so it does not touch the container and only measures water temperature.
* Heat the water.
* When the thermostat valve barely begins to open, read the thermometer. This is the opening temperature of this particular thermostat.
* If the valve stays open after the thermostat is removed from the water, the thermostat is defective and must be replaced.
* Several types of commercial testers are available. When using such a tester, be sure to follow the manufacturer's instructions.
* Markings on the thermostat normally indicate which end should face toward the radiator. Regardless of the markings, the sensored end must always be installed toward the engine.
* When replacing the thermostat, also replace the gasket that seals the thermostat in place and is positioned between the water outlet casting and the engine block.

* Generally, these gaskets are made of a composition fiber material and are die-cut to match the thermostat opening and mounting bolt configuration of the water outlet.
* Thermostat gaskets generally come with or without an adhesive backing. The adhesive backing of gaskets holds the thermostat securely centered in the mounting flange, leaving both hands of the technician free to align and bolt the thermostat securely in place.

Posted on Oct 07, 2009

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Free belt diagrams


http://serpentinebelthq.com/1991-jeep-wrangler-yj-4-0l-serpentine-belt-diagram/ her is a link for you to a diagram. I hope this helps

Jul 08, 2014 | 1991 Jeep Wrangler

1 Answer

My 1991 wrangler started overheating - i had the AC on and was stuck in traffic turned the heater on (ac off) and the temp returned to normal - where should i start?


You might check the fan,if it has a thermostatic clutch on it.
It should spin up with the same speed as the engine.And free wheel when the engine is first started. If it looks lazy,and just barely turning, in the heat of being stoped in traffic it may be whats causing the overheating.

Sep 18, 2010 | 1991 Jeep Wrangler

1 Answer

1991 jeep wrangler trouble starting and stalling


It could be a fuel filter clogged up or it could be a fuel pump going bad. Does the jeep start back up after it stalls? Is there any more symptoms?

Jan 27, 2010 | 1991 Jeep Wrangler

1 Answer

1991 jeep wrangler: alternator overcharging


It sounds as the voltage regulator which is built into the back of the alternator has stuck. Occaisionally this even happens on new ones. Would suggest taking the alternator back as it shoud be under warranty.

Jul 06, 2009 | 1991 Jeep Wrangler

2 Answers

Will a 1998 jeep 4L 2.5 motor work in a 1991 jeep wrangler?


Most likely yes. One thing about the older Jeeps is that they did not change the models much from year to year. If the two jeeps had the same engine, they are probably nearly 100% interchangeable.

Feb 12, 2009 | 1991 Jeep Wrangler

1 Answer

How do i bleed the tranny lines in 1991 jeep manual transmission


Auto parts stores have whats called trans. cooling line flush just ask them and they will know what you want.

Feb 09, 2009 | 1991 Jeep Wrangler

1 Answer

1991 Jeep Wrangler


Test....Test reply. Sorry for any inconvenience. Your question is still active.

Jun 16, 2008 | 1991 Jeep Wrangler

Not finding what you are looking for?
1991 Jeep Wrangler Logo

960 people viewed this question

Ask a Question

Usually answered in minutes!

Top Jeep Experts

yadayada
yadayada

Level 3 Expert

76109 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Kevin Daniels

Level 3 Expert

1455 Answers

Are you a Jeep Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...