Question about Chevrolet Suburban 1500

3 Answers

Where is the freeze plug located on a 1993 suburban 1500

Posted by on



3 Answers

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 1 Answer

I have a 1991 chevrolet caprice, that is throwing water out the side of the engine below the manifold on drivers side of the vehicle, its not a head gasket as the oil is normal, could it be a freeze plug by any chance.
please help

Posted on Feb 07, 2010

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points


    An expert that got 20 achievements.


    An expert that got 10 achievements.


    An expert that got 5 achievements.

  • Chevrolet Master
  • 2,002 Answers

There are a number of them depending on what engine you have but the placement is ,fairly standard. You will find a row of them,usually 3-4, on each side of the block about halfway between the oil pan and heads. They are about11/2 inches across and round, inset into the block. There are also some at the front and rear of the heads and the block.They are replaceable by a DIYer and are where a block heater is installed. Hope this helps.

Posted on Oct 07, 2009

  • Level 1:

    An expert who has achieved level 1.


    An expert who has answered 20 questions.


    An expert that has over 10 points.


    An expert whose answer got voted for 2 times.

  • Contributor
  • 34 Answers

Look under your exhaust manifold between the block and manifold and there a couple between your block and transmission

Posted on Oct 07, 2009

1 Suggested Answer

  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

1 Answer


ZUnder the hooed in the fuse and relay center on drivers side.

Jun 19, 2014 | 1993 GMC Suburban

1 Answer

1993 gmc suburban rough idle, stall in reverse

Idle air control (IAC) control rpm idle during idle.

Test it on idle with ALL electrical on full force.
RPM should increase.
If RPM remain the same then IAC is question.

Jan 13, 2014 | 1993 GMC Suburban

1 Answer

1993 GMC 1500 suburban 350 engine will not start. Engine starter turns, ignition does not fire.

i have a 1993 suburban gmc 1500. when i put the key in an turn it nothing happen at all.befor the car stop running it use to act crazy like start up in run great but when u turn it off it dont start back up. u wll have to wait than it will start..can u tell me what that can be..

Sep 13, 2010 | 1993 GMC Sierra

1 Answer

L need to locate the oil pump on a 1993 chevy suburban 1500 4x4

the oil pump is inside the engine,u must remove the oil pan to access it for replacement

Jul 27, 2010 | 1993 Chevrolet Suburban

1 Answer

How do i change a freeze plug on a 1993 chevy suburban 1500

They're all replaced the same way. bash in one side of the plug to turn it sideways in the hole. The freeze plug might be impossible to retrieve if it falls into the coolant passage — be careful.
Use a gripping device (pliers, ViseGrip, water-pump pliers, etc.) to get a hold on it, and wrench it out of the hole. Clean the hole thoroughly

coat the sealing surface of the new plug with Permatex No. 2 sealant, and drive the pug in squarely. Fins a pipe or socket that fits into the recess of the plug, and drive it in with that.

You need to do whatever is necessary to get square access to the plug. Sometimes that means removing cross members, sometimes that means removing steering parts, sometimes that means removing the engine.

An alternative is to get an expanding rubber replacement plug. To install those, all that is required is to be able to turn the nut in their center so as to get them to expand into the hole.

Jun 26, 2010 | 1993 Chevrolet Suburban

1 Answer

Where is the fuel safety switch located in a 1999 gmc suburban 4x4 1500

There is no fuel safety switch, thats a FORD trick. What is the problem?

Mar 18, 2010 | 1993 GMC Suburban

1 Answer

Chevy Suburban 1997 1500 won't start when Cold

it could be a tune up issue such as plug wires plugs . but my guess is its a computer engine temp sensor if it reads 5 degrees out of range it cuold give you a hard start or a no start problems the best way to look at this problem is with a scan tool when it is cold to see if the temp matches outside ambeint air temp 1 or 2 degrees ok b ut not 4 to five there is a nother way to check it buy useing dvom at a temp to omhs chart.

Jan 11, 2010 | 1997 Chevrolet Suburban

1 Answer

93 GMC Suburban, No Tail Lights

Check the trailer plug ground first. If in doubt. Ground in another location. Make sure the area is free of rust and the ground is tight.

May 10, 2009 | 1993 GMC Suburban

1 Answer

Freeze plug replacement

Hi, yes it can be when you remove motor mount and bracket, starter and exhaust manifold.

Dec 02, 2008 | 1993 Chevrolet Suburban

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

120 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts


Level 3 Expert

76682 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8531 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides