Question about 2000 Ford Windstar

1 Answer

Where are the kiddy locks on a 2000 Ford Windstar SEL Van

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Brigadier General:

    An expert that has over 10,000 points.

  • Master
  • 1,986 Answers

On the sliding doors, next to the latch when the door is open, there will be a tiny switch that you have to flip. It may also be a hole in the door with a symbol that you have to slide your key into to engage or disengage it

Posted on Oct 08, 2009

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Whenever it rains the van shows fuel err and will not start until I wiggle computer many times...nothing is wet under hood but its a problem every time it rains and its getting tiresome.


Find out whether all FSBs have been incorporated. Check battery age and condition. Find out whether alternator and starter are due for replacement. My 2000 Windstar is on its seventh battery. Many earlier problems were traced to battery failure.

Aug 16, 2016 | 2000 Ford Windstar SEL

1 Answer

Cranks once. Why doesn't it start?


Defective battery, possibly a defective cell

Dec 25, 2015 | 2000 Ford Windstar SEL

1 Answer

My overdrive light is flashing on and off on my 2000 ford Windstar van could a blown fuse be causing it


First of all have an auto parts store check for trouble codes...The flashing overdrive light is a warning that the overdrive unit is overheating and/or low on fluid...#1 choice is overheating and you will be looking at a costly rebuild if this is not attended too soon...Have your radiator, which also has a transmission cooler flushed, cleaned and refilled immediately...Have someone check if fluid is leaking then cleaned and filled with fresh fluid...saailer

Jun 18, 2015 | 2000 Ford Windstar SEL

1 Answer

My FORD WINDSTAR 2000 SEL driver side sliding door is locked and will not allow me to unlock it even when all other doors have been unlocked.


The door lock actuator is stuck in the lock position you will need to slim jim it open meaning you will have to lose the door lock actuator on the driver sideor replace the door lock lock actuator

Aug 18, 2011 | 2000 Ford Windstar

1 Answer

How do i change the rear stop bulb of my ford windstar 2000 sel?


open rear hatch and remove screws holding the entire light fixture in place. pull out gently as not to damage wires. disengage locking mechanism usually plastic and remove bulb and wire. carefully remove bulb without breaking it and replace with approved bulb

Dec 18, 2010 | 2000 Ford Windstar

2 Answers

1999 - 2000 ford winstar sel power locks very weak ...hardly work work erratically...driver and passenger locks do not lock or unlock automatically.....8-(


On the 2000 Windstar that I was working on, the casing for the door lock actuators had split and the lock knob on the top of the door would twitch when I hit the button, but would not lock or unlock fully. I replaced the door lock actuators (in stock at my local dealership) and cleared up the problem. Also check the bushings that link the rods inside the doors. They are plastic and occasionally wear out

May 16, 2009 | 2000 Ford Windstar

1 Answer

Change oxygen sensor 2001 ford windstar


fist unclip wire,then unscrew it with a 28mm spanner ,fitting procedure is the reverse .It turns anticlockwise to unscrew and clockwise to screw up ,torque setting is a grunt and two scuffed knuckles and max of 3 swear words

Jan 01, 2009 | 2001 Ford Windstar

Not finding what you are looking for?
2000 Ford Windstar Logo

232 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

75822 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

fordexpert

Level 3 Expert

5501 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...