Question about 1990 Plymouth Grand Voyager

1 Answer

How do we remove then replace the tumbler unit?

The key tumbler broke on our 1990 Plymouth Grand Voyager. We broke it out enough so we can use a screwdriver to start/stop the engine. How do we remove the entire thing and replace it so we can have a key again?

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Master
  • 909 Answers

Basically, hacksaw off the old casing, and replace with a new one, complete with key etc. it will come with "shear bolts" that will shear off the heads when tightened to the correct torque.

Posted on Oct 07, 2009

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Describe your 1990 plymouth grand voyager Problem: while driving,van surges as if its not getting enough fuel. It only surges when gas peddle is barely pressed. Have replaced fuel pump as well as filter


I have had same problem with my 1990 voyager .First have you retrieved the fault code ,by turning the key off and onwithin 5 seconds , 5 times ending up in on position ,then counting the flashes of the engine light. Procedure and codes are readly available online at this sight
I am 99 % positive you will find map senor is bad and needs to be replaced its located on the back of the manifold it has a three wire plug going to it it will cost under $40.00
they go bad quite often

Dec 17, 2010 | 1990 Plymouth Grand Voyager

1 Answer

How do I install 1999 Plymouth Grand Voyager headlamp assembly, both right and left side


open the bonnet and look down behind the headlamp, you should see some small type nuts, possibly about 6 that hold the unit in place, undo them, remove the multi wire plug from the unit and replace with the new headlamp assembly

Jun 26, 2010 | 1999 Plymouth Grand Voyager

1 Answer

On a 1990 Plymouth Grand Voyager what is the block that the brake lines go into on the drivers side rear?


It has to do with the load leveler, which is nothing but trouble trying to get the back brakes to work right. If you are having a problem getting good brakes to the back, it's not a bad idea to by-pass this block.

May 19, 2010 | 1990 Plymouth Grand Voyager

1 Answer

1990 PLYMOUTH GRAND VOYAGER HOW DO I REPLACE THE FRONT DIRECTIONAL BULB. I TRIED TO REMOVE THE WHOLE HEADLIGHT RIM, BUT THE BOTTOM DOESN'T HAVE A SCREW TO REMOVE.


You looked for screws at top,inside under hood, and way down low? Can't get at it enough inside hood to just turn bulb & pop it out? Sorry I had a 1987 & 91 but don't remember exact procedure, but i do not remember having to remove assy to get bulbs out. I could be wrong, but think I did them from behind.

Jun 05, 2009 | 1990 Plymouth Grand Voyager

1 Answer

1998 Phymouth grand voyager


Here is the relay for the rear:

bd11d44.gif
Remove the glove box then the four (4) hex screws on the blower motor cover. Then remove the mounting screws for the blower motor and set it down on the floor - it should have enough length in the wiring. Disconnect the the wiring connector them remove the rubber grommet and wiring harness through the blower housing. Installation is the reverse of removal. Good luck!

Mar 27, 2009 | 1990 Plymouth Grand Voyager

3 Answers

Replacing the fuel filter


check under the van on passenger side door track area

Mar 24, 2009 | 1990 Plymouth Grand Voyager

1 Answer

Ingnition tumbler broke cant start


If the key won't start it; it might not be the key ignition, but rather; the ignition that has a stem that goes from the key ignition down on the steering colunm. However, you can get key ignitions for them, or buy the whole steering colum then take the key ignition out of it. But, I would suggest more information is needed before I can conclude that it is just the key ignition. Hope this help~!

Jan 19, 2009 | 1990 Plymouth Grand Voyager

1 Answer

1992 grand voyager, key does not start van tumbler broke how do I hot wire it so I can start it


Just take a screw driver and pop of the ignition and then take a smaller screw driver and place it inside there should be a slot that you can access at this point...good luck.

Jan 19, 2009 | 1990 Plymouth Grand Voyager

Not finding what you are looking for?
1990 Plymouth Grand Voyager Logo

Related Topics:

93 people viewed this question

Ask a Question

Usually answered in minutes!

Top Plymouth Experts

yadayada
yadayada

Level 3 Expert

75077 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

7768 Answers

Are you a Plymouth Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...