Question about 1989 Chevrolet Camaro

2 Answers

Run turnd it off it not start back i changed ignition and neutrl safety switch and it still wont turn moter over

Posted by on

2 Answers

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 1 Answer

Sounds like your security is locked

Posted on Dec 15, 2009

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that got 5 achievements.

    Sergeant:

    An expert that has over 500 points.

    Governor:

    An expert whose answer got voted for 20 times.

  • Expert
  • 194 Answers

Try giving the small wire going onto the starter motor solenoid a wiggle

Posted on Oct 07, 2009

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Why wont my 91 camaro start i drove it home one day shut it off and it hasn't started since i have changed the emc box the ignition switch the key and tumbler but it still wont start i can get it to turn...


Possible neutral safety switch failed if its an automatic, or inhibitor switch if standard trans. Does it have an alarm ? Did you get the ign switch in properly, if its the style that mounts down low on the column,loosen the screws and slide it back toward steering wheel and recheck for start

Mar 21, 2015 | 1991 Chevrolet Camaro

1 Answer

Where is the solenoid switch located?


Engine side of the master cylinder you'll see a round 4pin connector with a flat top open it and make sure your connections are good

Nov 13, 2012 | 1995 Mercury Grand Marquis

1 Answer

97 chevy s10 wont start


Then the problem is likely the ignition switch, or the neutral safety switch. Try jamming it into park a couple of times to see if it helps. If it does, you will need to change the neutral safety. If it doesnt, probably going to need an ignition switch. Those trucks, jimmys, and blazers are famous for ignition switch problems.

Feb 06, 2012 | Cars & Trucks

1 Answer

No power to starter moter


Power will run from your ignition switch to neutral start switch on automatics, or clutch safety switch on manual transmissions. Those items, along with a starter relay, are all wired into your starting circuit, the start wire going to the starter solenoid on the starter. Of course, make sure your battery is fully charged. Use a multimeter and verify you have 12 volts to the big cable end on the starter. Now see if any power is on at starter solenoid terminal, with key in cranking position. If is power, remove starter and repair. If no power when key is in crank position, you'll have to trace your ignition starting circuit back to your ignition switch. can be a hassle, but, persistence pays off. BTW, when key is on, your dash lites do come on, don't they? Asking because that verifies you have power to ignition switch.

Oct 12, 2011 | 1998 Ford Escort

1 Answer

MY 2000 3.0 JAGUAR S-TYPE WAS ALSO RUNNING FINE ONE DAY WHEN I WAS COMING HOME 4RM THE STORE PULLING INTO MY DRIVE WAY MY CAR WAS ALSO RUNING FINE NO SIGNS NO SHAKING NOTHING AT ALL AND IT HAD HALF TANK...


SOUND LIKE FUEL PUMP NOT WORKING.TURN ON IGNITION SWITCH LISTEN FOR FUEL PUMP NOISE.SEE IF PUMP RUNNING IN FUEL TANK.IF NOT CHECK FUEL PUMP FUSE AND RELAY.IF ALL IS GOOD FUEL PUMP FAULTY.HAVE CAR CODE SCAN FOR FAULTY PCM AND ECM WHICH CONTROLS THE FUEL PUMP PRESSURE TO THE FUEL INJECTORS.

May 05, 2011 | 2000 Jaguar S-Type

1 Answer

96 ford explorer wont start. all power when turn key. nothing.


if it turns over from below,then its in the ignition switch and this also feeds power to the e.c.m. to make the engine fire so you either have a bad switch contact or the hot 12 volt wire to the ignition switch

Mar 20, 2010 | 1996 Ford Explorer

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

93 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts

yadayada
yadayada

Level 3 Expert

75117 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

7772 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...