Question about 1991 Toyota Corolla

1 Answer

Passenger side axel i cant seem to pull it out. how do i do it

Posted by on

  • 1 more comment 
  • gomesmichael Oct 07, 2009

    transmissino side

  • gomesmichael Oct 07, 2009

    maybe i was not clear enough. i am having a hard time getting it out from wher the wheel hub is. please respond

  • daniel timmons May 11, 2010

    which side of the axle? the hub side or the transmission side?



1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points


    An expert that gotĀ 5 achievements.


    An expert whose answer gotĀ voted for 20 times.


    An expert who has answered 20 or more questions within one hour.

  • Expert
  • 153 Answers

Use a prybar and pry in between the cv joint and the transmission with a swift jolt and it should pop out. dont pull on the axle itself because the joints will separate or get damaged nd you might not know it untill u go to drive it and have to start all over again

Posted on Oct 07, 2009

  • daniel timmons Oct 08, 2009

    remove the brake caliper, caliper bractet, and rotor. remove the big nut on the end of the axle. remove the hub from the ball joints, tie rod, etc. if the axle is siezed in the hub spray some wd-40 on the end where its siezed put the axle nut back on about 3 or 4 threads (so you dont mushroom the head) and hit it with a hammer. be carefull not to hit the wheel studs. once its freed remove the nut and the axle should slide right out.



1 Suggested Answer

  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
New users get to try the service completely Free afterwhich it costs $6 per call and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.

Posted on Jan 02, 2017


Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

1 Answer

Cant get bolts out of cv axel support braket in a mazda 626

This is a bracket mount that has the axle shaft going thru it on the passenger side . the axle must be removed from mount before it can be removed . there is a single bolt that presses against the axle shaft bearing and a snap ring that holds the bearing in the mount once removed the axle will slide out .

Mar 21, 2014 | 1997 Mazda 626

2 Answers

Power steering pump stopped working, need layman's terms for fixing it yourself

Layman's terms?? No there is no way to do that for this repair. Do you have the pulley removed from the pump? It pulls off with a special tool. Also how do you know the pump is defective, did you test the pressures? It is more likely the steering rack and pinion has failed.

Mar 07, 2014 | 1999 Dodge Caravan

1 Answer

Cant get driver side cv axle out on a 96 ford escort 1.9l

if you have taken the half axel off the wheel arm, then all it should take is a hard pull by hand to pop the half axel out of the transmission.

Jan 09, 2014 | Ford Escort Cars & Trucks

2 Answers

2001 mitsubishi eclipse gt spyder clutch removal. how do you get the axles out and how do you release the bearing for the tranmission to seperate

After the axel is removed from the outher wheel bearingf( seaparate the steering knuckle from the lower ball joint) and pull the axel out of the bearing after the axel nut has been removed then the axel will pry ou tof the transmission.. Might take a strong pry witht he haelp of a hammer. the one side might have a carrier bearing on the CV axel that bolted to the back of the engine block. It'll have to be unbolted. too. the starter will have to be removed also as all the bolts that hold the engine to the transmission.

May 14, 2011 | Mitsubishi Eclipse Spyder Cars & Trucks

2 Answers

I need to remove the driver side axle and i cant get it out of tranny

There is a "C" clip that holds it in there. Put your pry bar on the fat part of the halfshaft (axle) and give it a few smacks with a hammer. These jolts should knock it loose to be able to remove it. If you cant get room to hit it with a hammer you will have to use a pry bar and just keep working at it on both sides.

Jan 15, 2011 | 1996 Dodge Neon

1 Answer

I dont know how to remove the passenger side front axel in my 1986 ford f150

pull off the rotor-caliper-and behind the rotor is the hub,unbolt it and use a chisel to separate it from the housing,pull that off and wiggle the axel shaft lightly while pulling out and it barely fits through but it will come out.there is a rubber boot on the inner part of the axel,so cut off the clamp so it will come apart..dont hit the threads on the hub,ive done that once and had to use a triangler file to fix the threads

Dec 25, 2009 | 1986 Ford F150 SuperCab

1 Answer

How to remove front passenger side wheel berring once it was seized and now we cant get the axel out from behind

best bet is to take it to a mechanic. they had to use a pnuematic hammer to get mine off

Jun 21, 2009 | 1989 Ford Tempo

1 Answer

Just in an accident, how much is an axel

You would need to get in touch with your local recycling yard, as prices vary from place to place. buying new would be HELL to find, and expensive. it may not hurt to call a dealer.

Feb 27, 2009 | 1999 Dodge Caravan

Not finding what you are looking for?
1991 Toyota Corolla Logo

Related Topics:

140 people viewed this question

Ask a Question

Usually answered in minutes!

Top Toyota Experts


Level 3 Expert

76649 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8522 Answers

Are you a Toyota Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides