Question about 1978 Chevrolet Chevette

1 Answer

How do i replace the clutch in my 1978 chevette

Posted by on

  • yadayada
    yadayada May 11, 2010

    u nneed a service maunual for this. here is where to get a used one.http://www.faxonautoliterature.com/produ...

×

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Brigadier General:

    An expert that has over 10,000 points.

  • Master
  • 4,044 Answers

Go to the local auto parts store and get a repair manual on your vehicle. You will need it as you will need instructions on removing the transmissions and then removing the clutch and bearings and re-installing them.

Posted on Oct 07, 2009

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya Mechanic can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repair professionals here in the US.
click here to Talk to a Mechanic (only for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How do I remove and replace the fuel pump on a 1978 Chevette?


Hi Dan,I use to have a couple of Chevettes,great on gas,Here's a link on your fuel pump removal,never had a issue with that,on these,you have to change the timing belt every 3 years ,the belt will stretch and jump time and the plugs will get fouled,here's another link on your timing belt if the fuel pump replacement doesn't work,also check your spark plugs. Repair Guides Carbureted Fuel System Fuel Pump AutoZone com Here's the timing belt link. Repair Guides Engine Mechanical Timing Belt And Sprockets AutoZone com

Dec 10, 2014 | 1978 Chevrolet Chevette

1 Answer

87 chevette instrumental panel fuse keeps blowing out when i put a new one in i just bought the car and trying to figure it out it did not have a fuse in it when i purchased it


install a test light (12v bulb) or a buzzer in palce of the fuse. When you get the light or buzzer to stop, you will have found the short circuit. Look in the owner manual for what this fuse protects.

Aug 27, 2010 | 1978 Chevrolet Chevette

1 Answer

Need to know how to remove the back seat in 78chevy chevette


Get a number 10 metric or a 7/16" socket and feel at the base of the seat bottom....should be two bolts holding the seat to the floor one on each side, use your light and perhaps you will need to peel back the carpet going to the seat bottom.
Happy Motoring!!

Jul 26, 2010 | 1978 Chevrolet Chevette

1 Answer

What is the proper timing on a 1978 Chevrolet Chevette?


My Motor book gives no timing for your engine that year, which suggests that it is preset. However that size engine ( should be a 97 cu. in. or 1600cc) for the 2 years before shows 8 degrees before TDC for a manual trans and 10 for an automatic. Hope this helps.

Jul 12, 2010 | 1978 Chevrolet Chevette

1 Answer

One of muffer runs cold and the other runs hot


one is the cadlic conver the rear one is the muffler

Mar 20, 2010 | 1978 Chevrolet Chevette

1 Answer

The ignition lock is jammed


this happened on my 74 corvette. I had to replace the ignition key cylinder chevy had a pretty common problem with this if I remember correctly there is a small hole where you put the key in you take something like a paper clip and insert it in the hole this releases the cylinder and it pulls out replace with a new cylinder which just pops in

Oct 23, 2009 | 1978 Chevrolet Chevette

1 Answer

Wire problems


its probably causing a short. find what wire it goes to and get a connector and reconnect it.

Apr 28, 2009 | 1978 Chevrolet Chevette

2 Answers

1978 chevy chevette


Check engine compression. Those engines have a cylinder arrangement that looks like four drinking glasses sitting inside a cardboard box. During overheat, cylinders drop below deck height and do not seal against gasket. Non-technical repair was to draw file the deck 'till it's even with cylinder tops.
Obviously, check all of your work as well, you may have inadvertently knocked something loose that has to do with starting.

Apr 16, 2009 | 1978 Chevrolet Chevette

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

121 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts

yadayada
yadayada

Level 3 Expert

77169 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22265 Answers

Ronny Bennett Sr.
Ronny Bennett Sr.

Level 3 Expert

6927 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...