Question about 1989 Chevrolet C1500

1 Answer

The bracket that holds the alternator and the power steering pump along with a couple other components is cracked behind the power steering pump. is this bracket easy to find/replace or do i have to bring it to a shop to fix/replace?

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Brigadier General:

    An expert that has over 10,000 points.

  • Master
  • 4,044 Answers

You might find one at a Junk Yard or be able to order it from the dealer, that is where I would look for it in that order. As far as how easy it is to replace that will depend on how everything is connected and if the job requires special tools.

Posted on Oct 07, 2009

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Cant get alternator out of engine compartment


Hey all, found this for 3.3L engine.
3.3-mgkxnf303xgr2hvssd3liypr-1-0.jpg

May 06, 2017 | 1995 Plymouth Voyager

1 Answer

Im trying to change my alternator on my 97 chrysler sebring coupe lxi but it seems impossible to do it without taking other parts off to get it out and also put the new one in because its real compact


Hi there:
Check this procedure on 2.5L (VIN N) Engine...


  1. Disconnect the negative battery cable.
  2. Remove the right side under cover.
  3. Remove the speed control vacuum reservoir and related components as required for alternator access.
  4. Remove the power steering pump cover.
  5. Remove the A/C compressor drive belt.
  6. Remove the alternator/power steering pump drive belt.
  7. Remove the intake manifold plenum.
  8. Remove the upper alternator bracket.
  9. Remove the intake manifold plenum stay.
  10. Detach the electrical connections at the alternator.
  11. Unfasten the upper and lower bolts and remove the alternator. Be very careful not to damage neighboring components while removing the alternator.


8_22_2012_2_51_45_pm.gif

Fig. 8: Alternator assembly installation-2.5L engine (VIN N) - Zoom Image link HERE


To install:

  1. Connect the wiring to the alternator.
  2. Place the alternator on its lower bracket and install the upper and lower bolts finger-tight.
  3. Install the upper alternator bracket.
  4. Install the alternator/power steering pump belt, making sure it is properly seated.
  5. Adjust the drive belt to the correct tension using the belt adjuster, then tighten the upper mounting bolt to 16 ft. lbs. (22 Nm) and the lower mounting bolt to 30 ft. lbs. (41 Nm).
  6. Install the intake manifold plenum.
  7. Install the intake manifold plenum stay.
  8. Install the A/C compressor drive belt.
  9. Install the power steering pump cover.
  10. Connect the negative battery cable.
  11. Check the charging system operation.



Hope this helps; also keep in mind that your feedback is important and I`ll appreciate your time and consideration if you leave some testimonial comment about this answer.

Thank you for using FixYa, have a nice day.

Aug 22, 2012 | Cars & Trucks

1 Answer

The tension belt keeps coming off of my 1999 Town and Country. First the power steering fluid starts to leak, then it overheats. Now the battery is dead. I have already repaired the tension belt before...


Hi,
I assume you mean you have replaced the serpentine drive belt before? When your belt comes off, it is not operating your water pump and alternator or power steering pump, giving you the overheat and dead battery. Shouldnt make power steering fluid leak though. Does the power steering fluid leak all the time, or just when the belt comes off? If it leaks all the time from the pump area, you could have a bad seal and bearing in the pump causing the pulley to wobble and that makes the belt walk off. First, locate the belt routing diagram on the engine cowl (front of vehicle under the hood) or make a drawing of how the belt is routed for re-assembly use. Loosen belt tension at tensioner and take belt loose from a pulley that is easily accessed. Use your hands to wiggle all your pulleys and feel for excessive play in any of them or the components themselves. (water pump, power steering pump,A/C compressor and alternator.) If component play, you could have loose bolts causing wobble. If pulley play, could be bad bearing in component which would need replaced. Pay special attention to excess movement in the tensioner pulley itself. Also visually check for sideways alignment of pulleys. If pulleys are not aligned correctly, it will make the belt walk off also. That is usually a bracket misaligned or bolt holes in bracket worn out. If all checks good, I would suspect a worn out belt or belt tensioner that is not holding enough / proper tesion on belt allowing it to walk off. It will take you about an hour to check these things, repair costs depend on what you discover as a potential problem,as components can be costly.
Let us know what you find......Thanks, Mike

Jun 24, 2011 | Chrysler Town & Country Cars & Trucks

1 Answer

The engine service light code says the cam shaft sensor is going out. Got a new cam sensor but cant get out because of the power steering pump in the way and won't let the sensor come all the way out...


Remove the serpentine belt. You will then be able to rotate the power steering pump pulley by hand. If you look through the holes in the pulley you will see the bolt heads that hold the pump in place. There will be three of them. Remove those bolts and you will be able to wiggle the power steering pump out of the way. There will also sometimes be a bracket behind the alternator that holds the power steering lines in place. You may have to remove that ad well.

May 21, 2011 | 2001 Buick Century

1 Answer

How do you get your power steering pump bracket off so you can get your power steering pump off a 2004 Ford Tarus


This may be helpful. Not familiar with '04, but 1998 Ford Taurus requires you to first pull off the power steering pump pulley using a pulley tool borrowed from a local parts store. The alternative is to break the pulley (plastic) with a hammer to get to the bolts and then use the pulley tool to
get the rest of the pulley loose and replace with another 10 or 11 dollar pulley after you have remounted the steering pump and bracket. The reason the pulley has to come off is there is another
bolt behind the pulley. Hope this is helpful.

Feb 24, 2011 | 2004 Ford Taurus

1 Answer

How to install a power steering pump for a 1997 chrysler seabring conv


Chrysler Cirrus/Stratus/Sebring/Avenger/Breeze 1995-1998
Power Steering Pump - REMOVAL & INSTALLATION

Cirrus, Stratus, Sebring Convertible and Breeze
(see Figures 1, 2, 3 and 4)
  1. Disconnect the negative battery cable from the left strut tower. The ground cable is equipped with an insulator grommet, which should be placed on the stud to prevent the negative battery cable from accidentally grounding.
  2. Siphon as much power steering fluid out of the reservoir as possible.
  3. Raise and safely support the vehicle.
  4. Remove the right front tire and wheel assembly.
  5. Remove the splash shield from the right front wheel well.
c901554.jpg

Fig. 1: Power steering pressure hose attachment to the pump-with Variable-Assist steering

8786c07.jpg

Fig. 2: Power steering pressure hose attachment to the pump-without Variable-Assist steering
  1. Disconnect the power steering pressure hose from the pump.
  2. Remove the hose connection on the power steering pump.
e7733b2.jpg

Fig. 3: Typical power steering pump front bracket attachment
  1. Remove the power steering adjusting bolt.
  2. Remove the power steering pump rear attaching bolt.
  3. If so equipped, remove the Anti-lock Brake System (ABS) hydraulic control unit heat shield.
  4. Remove the wheel speed sensor retainer bracket from the right inner fender.
  5. Remove the wheel speed sensor sealing grommet from the right inner fender.
  6. Disconnect the speed sensor wiring.
  7. Push the wiring through the hole in the inner fender.
If not equipped with anti-lock brakes, the hole will just have a sealing plug.
  1. Remove the bolt attaching the power steering front bracket to the mounting bracket. Access to the bolt is gained through the hole for the speed sensor wiring.
  2. Remove the power steering pump drive belt.
  3. Remove the power steering pump and the front bracket as an assembly.
To install:
  1. Install the power steering pump and bracket.
  2. Reinstall the bolt at the adjusting slot, but do not tighten.
  3. Reinstall the bolt mounting the power steering pump to the rear mounting bracket, but do not tighten.
  4. Reinstall the power steering pump top bolt, but do not tighten.
  5. Reconnect the power steering hoses.
b72b14a.jpg

Fig. 4: Install a new O-ring gasket on the hose fitting
Use a new O-ring when reinstalling the power steering pressure hose.
  1. Reinstall the drive belt.
  2. Adjust the drive belt and tighten the power steering pump bolts to 40 ft. lbs. (54 Nm).
  3. Reinstall the splash shield.
  4. Reinstall the tire and wheel assembly.
  5. Lower the vehicle.
  6. Reconnect the negative battery cable.
  7. Refill the reservoir and bleed the power steering system.


Sebring Coupe and Avenger
  1. Disconnect the negative battery cable.
  2. Remove (drain, suction pump, etc.) as much power steering fluid as possible.
  3. Disconnect the return fluid line. Remove the reservoir cap and allow the return line to drain the fluid from the reservoir. If the fluid is contaminated, disconnect the ignition high tension cable and crank the engine several times to drain the fluid from the gearbox.
Cover any components located underneath the power steering pump with a shop towel to protect them from damage due to power steering fluid spillage. For example, the A/C compressor or alternator, depending on vehicle and engine, is below the power steering pump, so cover the A/C compressor or alternator with a shop towel before removing any hoses.
  1. Loosen (but do not remove) the power steering pump mounting bolts and remove the drive belt.
  2. Remove the pressure switch connector from the side of the pump.
  3. Disconnect the pressure line.
  4. Unbolt and remove the pump from the mounting bracket.
To install:
  1. Clean all parts well. Inspect the pump pulley for cracks. Check the hoses carefully for cracks or signs of weakness.
  2. Install the pump, wrap the belt around the pulley and lightly tighten the mounting bolts.
  3. Replace the O-rings and connect the pressure line. Connect the pressure line so the notch in the fitting aligns and contacts the pump's guide bracket. Tighten the fitting to 13 ft. lbs. (18 Nm).
  4. Connect the return line and secure with the clamp.
  5. Fasten the pressure switch connector.
  6. Adjust the power steering belt for proper tension and tighten the adjusting bolts.
Use only MOPAR ATF PLUS automatic transmission fluid type 7176, ATF+3 automatic transmission fluid, or equivalent, in the power steering system of Sebring coupe and Avenger models.
  1. Refill the reservoir and bleed the power steering system.

Hope this help to solve it (remember comment and rated this). TY for using Fixya.

May 13, 2010 | 1997 Chrysler Sebring

3 Answers

How do you remove the Power Steering Pump and bracket. I have taken off several bolts but it still is not letting loose. Help


3.0L (VIN 3) Engine

f799ffc.gif
Power steering pump mounting detail (3.0L engine)

  1. Disconnect and isolate the negative battery cable.
  2. Remove the accessory drive belt. The belt does not have to be removed from the engine.
  3. Raise and safely support the vehicle.
  4. Disconnect the wiring harness connector to the oxygen sensor which is accessible through the oxygen sensor wiring harness grommet in the vehicle floor pan.
  5. Remove the catalytic converter from the exhaust manifold and remove all exhaust system hangers and isolators from the exhaust system brackets. Move exhaust system out of the way as far rearward and to the left as possible to provide access to the power steering pump.
  6. Place a drain pan under the power steering pump. Remove the power steering fluid return line hose on the front suspension cradle. Allow the fluid to drain from the pump and hose.
  7. Remove the accessory drive belt splash shield.
  8. Disconnect the power steering remote reservoir supply hose from the fitting on the power steering pump. Allow fluid to drain from the hose.
  9. Remove power steering fluid pressure line from the power steering pump and drain any excess power steering fluid.
  10. Remove the power steering fluid return hose from the power steering pump.
  11. Remove the rear support bracket mounted behind the power steering pump to the engine block.
  12. Remove the 2 mounting bolts that secure the pump to the alternator/power steering pump and belt tensioner mounting bracket.
  13. Remove the power steering pump and pulley assembly out from the vehicle. Transfer all required parts from the pump to the new replacement pump before installation.
To install:
  1. Position the front of the power steering pump up onto the mounting bracket. Torque the 2 power steering pump-to-mounting bracket bolts to 40 ft. lbs. (54 Nm).
  2. Install the rear power steering pump-to-engine block support bracket. Torque the 2 support bracket mounting bolts to 40ft. lbs. (54 Nm). Install the nut to the mounting stud behind the pump and torque to 40 ft. lbs. (54 Nm).
  3. Install the high pressure fluid line to the pump output fitting. Torque the high pressure line-to-power steering pump fitting to 275 inch lbs. (31 Nm). Be sure to inspect the pressure line O-ring for any damage before connecting the pressure line to the steering pump.
  4. Install the low pressure power steering fluid hose to the power steering pump low pressure fitting. Be sure the hose clamps are properly reinstalled and hoses are clear of the accessory drive belts.
  5. Install the accessory drive belt.
  6. Install the hose on the power steering fluid return line on the front suspension cradle. Be sure the hose clamps and heat shield tubes are correctly reinstalled.
  7. Reconnect the exhaust pipe to the exhaust manifold. Install the hangers and isolators onto the exhaust system brackets. torque the nuts and bolts to 250 inch lbs. (28 Nm).
  8. Reconnect the wiring harness connectors to the oxygen sensor. Install the wiring harness grommet into the vehicle floor pan.
  9. Install the accessory drive belt splash shield.
  10. Remove the drain pan and lower the vehicle.
  11. Refill the power steering pump reservoir with the correct amount of clean power steering fluid.
  12. Reconnect the negative battery cable. Bleed the power steering system.
  13. Run the engine and check the system for leaks and proper steering operation.

3.3L (VIN R) & 3.8L (VIN L) Engines

0b3de97.gif
Rear support bracket mounting detail (3.3 & 3.8L engines)

6764c64.gif
Power steering pump mounting detail (3.3 & 3.8L engines)

  1. Remove and isolate the negative battery cable.
  2. Raise and safely support the vehicle. Place a drain pan under the power steering pump.
  3. Disconnect the wiring harness connector to the oxygen sensor which is accessible through the oxygen sensor wiring harness grommet in the vehicle floor pan.
  4. Remove the catalytic converter from the exhaust manifold and remove all exhaust system hangers and isolators from the exhaust system brackets. Move exhaust system out of the way as far rearward and to the left as possible to provide access to the power steering pump.
  5. Remove the power steering fluid return line hose on the front suspension cradle. Allow the fluid to drain from the pump and hose.
  6. Remove the accessory drive belt splash shield.
  7. Remove accessory drive belt.
  8. Disconnect the power steering remote reservoir supply hose from the fitting on the power steering pump. Allow fluid to drain from the hose.
  9. Remove power steering fluid pressure line from the power steering pump and drain any excess power steering fluid.
  10. Remove the power steering fluid return hose from the power steering pump.
  11. Remove the rear support bracket mounted behind the power steering pump to the engine block.
  12. Remove the 3 mounting bolts that secure the pump to the alternator/power steering pump and belt tensioner mounting bracket.
  13. Remove the power steering pump and pulley assembly from the vehicle. Transfer all required parts from the pump to the new replacement pump before installation.
To install:
  1. Position the front of the power steering pump up onto the mounting bracket. Torque the 3 power steering pump-to-mounting bracket bolts to 40 ft. lbs. (54 Nm).
  2. Install the rear power steering pump-to-engine block support bracket. Torque the support bracket mounting bolts to 40 ft. lbs. (54 Nm). Install the nut to the mounting stud behind the pump and torque to 40 ft. lbs. (54 Nm).
  3. Install the high pressure fluid line to the pump output fitting. Torque the high pressure line-to-power steering pump fitting to 275 inch lbs. (31 Nm). Be sure to inspect the pressure line O-ring for any damage before connecting the pressure line to the steering pump.
  4. Install the low pressure power steering fluid hose to the power steering pump low pressure fitting. Be sure the hose clamps are properly reinstalled and hoses are clear of the accessory drive belts.
  5. Install the accessory drive belt.
  6. Install the hose on the power steering fluid return line on the front suspension cradle. Be sure the hose clamps and heat shield tubes are correctly reinstalled.
  7. Reconnect the exhaust pipe to the exhaust manifold. Install the hangers and isolators onto the exhaust system brackets. Torque the nuts and bolts to 250 inch lbs. (28 Nm).
  8. Reconnect the wiring harness connectors to the oxygen sensor. Install the wiring harness grommet into the vehicle floor pan.
  9. Install the accessory drive belt splash shield.
  10. Remove the drain pan and lower the vehicle.
  11. Refill the power steering pump reservoir with the correct amount of clean power steering fluid.
  12. Reconnect the negative battery cable. Bleed the power steering system.
  13. Run the engine and check the system for leaks and proper steering operation.

Nov 03, 2009 | 1997 Chrysler Town & Country

1 Answer

Lost my alternator belt on my 1994 isuzu rodeo. It's situated behind 2 other belts. Where do I begin with loosening things to get the other belts out of the way so I can install the new alternator belt?...


14mm spanner
12mm socket
13mm socket
short socket extension bar
ratchet
adjustable wrench 250mm
tyre lever or long thin bar for levering out alternator
there are 2, 14mm bolts in front bracket of power steering pump loosen a couple of turns only then loosen stud nut at rear of power steering pump then you can move pump in/out by turning 14mm long bolt you see thread for just left of power steering pump pulley
then the alternator is a 12 or some times 13mm bolt at top front section to loosen then lever in and out, must hold tension on lever with belt on while doing this up (2nd person to hold lever)

Jul 11, 2009 | 1994 Isuzu Rodeo

1 Answer

79 ford 460 pully diagram


power steering pump goes to the lower left(as you sit in the vehicle) A/C compressor above that and somewhat towards the centre. Alternator goes on the lower right(this the one that is not obvious) Hope this helps!

May 28, 2009 | 1983 Ford Econoline

1 Answer

Oil pressure gauge keeps fluxuating. Think it is the sensor. Want to know where the sensor is located on my 1994 lincoln continental


The oil sending unit is located below the power steering pump. 
You can get to it by removing the alternator, then the three bolts around the power steering pump bracket. Remove the small pulley on the bracket and pull back on the power steering bracket. Look behind bracket and you will see the oil sending unit. 

Disconnect the wire from the oil sending unit. Use a deep socket (1 1/16) to remove unit. 

While you have unit remove, I would go ahead and use an oil pressure gauge to test the oil pump pressure. 

Good luck and hope this helps

May 02, 2009 | Ford Lincoln Continental Cars & Trucks

Not finding what you are looking for?
Cars & Trucks Logo

160 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts

yadayada
yadayada

Level 3 Expert

75066 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

7754 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...