Question about 2003 Dodge Durango

Open Question

Code reader says there is a misfire from cylinders 1 and 6.Changed all plugs,swapped coilpack from no. 1 cylinder to no. 3 with same results.Compression test checked out fine.Shop manual says there should be 12 volts with key on at injector connections-not getting anything here.Where should I look for wiring problem?Check engine has gone out but still skipping badly on those two cylinders.Any ideas.Thanks,Linwood

Posted by on

  • Jeff Turcotte
    Jeff Turcotte Jul 23, 2017

    Hi 98skidoo, I want to help you with your question, but I need more information from you. Can you please add details in the comment box? You say there is no voltage at injectors but the car runs. Is it only injectors 1 and 6 that do not have power?

×

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 188 Answers

SOURCE: 2004 chevy k2500. misfire

sound like you a cam shaft sensor going out and the sensor is not hitting the mark, makingit misfire.?????

Posted on Feb 04, 2009

Molson02536
  • 3854 Answers

SOURCE: Check engine light

A multi misfire may mean that one or more of the following has happened:
Faulty spark plug or wires, Faulty coil (pack), Faulty oxygen sensor(s), Faulty fuel injector(s), Stuck/blocked EGR valve / passages, Faulty camshaft position sensor, Defective computer.

The engine is stumbling or hesitating, check all wiring and connectors that lead to the cylinders (i.e. spark plugs). Depending on how long the ignition components have been in the car, it may be a good idea to replace them as part of your regular maintenance schedule. I would suggest spark plugs, spark plug wire, distributor cap, and rotor (if applicable). Otherwise, check the coils (a.k.a. coil packs). In some cases, the the problems were faulty fuel injectors. 

Random misfires that jump around from one cylinder to another (read: P030x codes) also will set a P0300 code. The underlying cause is often a lean fuel condition, which may be due to a vacuum leak in the intake manifold or unmetered air getting past the airflow sensor, or an EGR valve that is stuck open.

Good luck and hope this information helps, keep me posted, be glad to help you get the truck running 100% again. Not sure if your running a K&N air filter, and if you are there may be a flim of oil on the MAF sensor that is making you run lean. You may want to spray down the MAF sensor with a can of MAF cleaner. 

Posted on Jul 02, 2009

  • 412 Answers

SOURCE: 2004 Neon SXT cylinder misfire

TRY REPLACING THE CRANKSHAFT POSITION SENSOR..HAVE SEEN THESE CAUSE MISFIRES AND LOW VOLTAGE DTCS AS PCM THINKS VEHICLE IS NOT RUNNING..ALTERNATOR MAY NOT BE PUTTING OUT PROPERLY

Posted on Jul 07, 2009

  • 34 Answers

SOURCE: misfire on #6 and #8 cylinder 1996 Dodge Ram 1500

Check the spark plug wiring . There are several places where the wires cross each other. These wire cross points MUST be at right angles to each other. Or you will have a misfiring problem.

Posted on Jul 07, 2009

  • 1 Answer

SOURCE: misfire

Check your cam. position sensor

Posted on Jul 25, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Check engine light code p2196,p2197, po300 ,304,305,306,p2 ,Im freeking out.


P0300 Random/Multiple Cylinder Misfire Detected P0301 Cylinder 1 Misfire Detected P0302 Cylinder 2 Misfire Detected P0303 Cylinder 3 Misfire Detected P0304 Cylinder 4 Misfire Detected P0305 Cylinder 5 Misfire Detected P0306 Cylinder 6 Misfire Detected P0307 Cylinder 7 Misfire Detected P0308 Cylinder 8 Misfire Detected P0309 Cylinder 9 Misfire Detected P0310 Cylinder 10 Misfire Detected P0311 Cylinder 11 Misfire Detected P0312 Cylinder 12 Misfire Detected P0313 Misfire Detected with Low Fuel P0314 Single Cylinder Misfire (Cylinder not Specified) P0315 Crankshaft Position System Variation Not Learned P0316 Misfire Detected On Startup (First 1000 Revolutions)

Read more at: http://www.obd-codes.com/trouble_codes/
Copyright © OBD-Codes.com
-----------------------------------------------------------------------
P2195 O2 Sensor Signal Stuck Lean Bank1 Sensor 1 P2196 O2 Sensor Signal Stuck Rich Bank1 Sensor 1 P2197 O2 Sensor Signal Stuck Lean Bank2 Sensor 1 P2198 O2 Sensor Signal Stuck Rich Bank2 Sensor 1

Read more at: http://www.obd-codes.com/trouble_codes/
Copyright © OBD-Codes.com http://www.obd-codes.com/p0002

May 07, 2015 | 2006 Ford Taurus SEL

1 Answer

Misfire on Cylinder 3 swapped plugs between 3 and 4 on Pontiak Aztek 2003. Misfire remained on cylinder 3. Swapped ignition coil 3 and 6 with ignition coil 1 and 4 misfire still on cylinder 3


Spark Plug swapping is a waste of time

You may never have a failed plug in 70 years
of driving

Now you move on to professional help

You could have failed valves,failed intake gasket
or other issues

Dec 04, 2014 | 2001 Pontiac Aztek

1 Answer

Misfire on Cylinder 3 swapped plugs between 3 and 4 on Pontiak Aztek 2003. Misfire remained on cylinder 3. Swapped ignition coil 3 and 6 with ignition coil 1 and 4 misfire still on cylinder 3


Try a new plug wire on cyl 3 if that doesn't fix it you could have a bad valve or compression problem on cyl 3 Try doing a compression test also If it has injectors for each cylinder you could have a bad injector for cylinder number 3

Dec 04, 2014 | 2001 Pontiac Aztek

1 Answer

How do I know which is cylinder 2 on a vortex 4200 ,straight 6?


The #1 cylinder is the one closest to the radiator. Number 2 is just behind #1. It takes all 4 ingredients to fire a cylinder - Air, Fuel, Spark, and Timing. If you only have one misfire code (P0302 - Cylinder #2 Misfire), it should be a relatively easy diagnosis and fix. You mentioned changing the coil, so let's start with Spark. I'm going to assume you have a code reader. First, remove the spark plug in #2 cylinder. Examine the threaded end. Is it wet and/or smell like fuel? If so, chances are the misfire is caused by a weak/absent spark. To confirm, swap it with a known good cylinder - example #3 cylinder. Clear the code. Start it and let it run for a couple of minutes. If a code appears with P0303 (the last digit refers to cylinder number), then you have found the culprit - bad spark plug. If the code reappeared with P0302 (Cylinder #2 again), then swap out the spark plug wire (both ends). Clear the code. Start and run for a couple of minutes. Again, if it appears on Cylinder #3 - the plug wire is the culprit. If the P0302 code comes back, swap the coil. See where this is going?

Now, when you first pulled the plug from Cylinder #2, if it wasn't wet or smelled of fuel, chances are Spark is not the issue. Was the plug dry and/or ashy? Possible cause is no fuel reaching the combustion chamber (cylinder). Using an automotive stethoscope, listen to the fuel injector for cylinder #2 while the motor is running. Should hear a regular and rhythmic ticking sound. Like a fast clock. (Use a long handled screwdriver touching one end to your ear and the other to the top of the injector if you dont have a stethoscope). No clicking or irregular clicking means fuel injector is not working (no sound) or is not working properly. Like searching for the Spark problem, swap the injector in #2 cylinder with #3. Clear code. Start and run. If the problem moved to #3, ithat injector is the culprit. If it stayed on #2, it is likely your wiring to that injector - check the whole harness for loose connections or swelled with oil wires/connectors. Keep pecking away at the fuel delivery system for that cylinder. Stay looking for things that affect only that cylinder.

When you pulled the plug, was it fairly normal looking? Then this misfire code might only be a timing problem. It is likely not a timing problem in your case, because timing affects all cylinders, but I thought I would just mention it since Timing is an important part of combustion. Also, if timing were a culprit here, another code would usually appear signifying the Camshaft Positon Sensor or Crankshaft Position Sensor was/is failed, or it is possible for the timing belt/chain to skip a knurl on a sproket and throw the timing off, but like I said, it would almost always cause multiple/random (Code P0300) misfires.

And finally, when you pulled the plug earlier, if it was an oily sticky mess, then the culprit might be Air - or compression/lack of compression. Lets hope not, because when Air is the cause of a misfire, it is usually an expensive fix. Need to perform a compression test. If you have little or no compression in the cylinder, it is likely a bad head gasket or a stuck/sticky/broken/chipped valve (exhaust or intake). Any of these things are bad news and expensive to fix in a shop. Also bad news and time consuming and difficult task for a shade tree mechanic.

Now, clear that code and get started! Good luck!



Now If

Apr 04, 2014 | 2003 GMC Envoy

3 Answers

CODES-PO301-PO303-PO316- CHANGED PLUGS & WIRES. STILL MISS ON START UP, GOES AWAY MOST OF THE TIME ABOVE 1000 R.P.M


P0301 - Cylinder 1 Misfire Detected.

Causes:
- Improper spark plug at cylinder #1
- Insufficient compression at cylinder #1
- Incorrect fuel pressure
- The injector circuit is open or shorted at cylinder #1
- Fuel injector #1 may be faulty
- Intake air leak

Solutions:
- Perform Injector Service
- Replaced Spark Plug #1
- Replaced Injector #1
- Replaced Ignition Coil #1

P0303 - Cylinder 3 Misfire Detected.
Follow info from P0301.

P0316 - Misfire Occurred In The First 1,000 Engine Revolutions.

Causes:
- Damaged CKP sensor.
- Ignition System.
- Fuel Injectors
- Running out of fuel
- Fuel Quality
- Base engine
- Damaged Powertrain Control Module

Solutions:
Usually the P0316 is combine with a P03XX codes. The P03XX code indicates in which cylinder the misfire occurred.

Jan 17, 2011 | 2002 Mercury Sable

1 Answer

While driving the car started to miss badly, the check engine light came on then began to flash. checked for codes, engine missfire was the only stored code. owners man. said cat. problem ?


It's not a cat problem or you'd have misfires on all cylinders. P0300 is random misfires, and the codes increment to show what cylinder is misfiring. P0301 is a misfire on cylinder 1, P0302 is cylinder 2, etc. You likely have a bad coilpack. Whichever cylinder is indicated, replace that coilpack.

Sep 16, 2010 | 2004 Audi A4

2 Answers

Check Engine Light is on and the code is P0303


Hello I need a help.
I have 1999 lincoln town car 4.6L V8.They have check engine light on. P 0303 cylinder 3 missfire.
I was changed spark plugs,fuel filter. check compression test 150psi. fuel pressuer 50.
swiching cylinder 1 to 3 fuel injector and coil. but they still have engine code

Feb 27, 2009 | 1999 Lincoln Town Car

2 Answers

Very Rough running engine


I think the auto-lite plugs are probably your problem. yes it sounds like mis-firing. That's one of the few times the check engine light flashes. I'd suggest changing the plugs to a NGK plug, that's the ONLY plug we use in our Audi's and VW's (work at a VW/Audi shop). Try that, and it should take care of the rough running, if not, it will probably need coils too.

Jan 13, 2009 | 2004 Audi TT

1 Answer

Audi A6 Misfires


You may have a coil pack going bad. They're on the front top of the engine - you'll see them if you follow the spark plug wires back. Do you have any codes from having the engine scanned? If you can get it scanned (AutoZone will do it free), post the codes up and we'll see which cylinder(s) are misfiring. From there, you can swap coilpacks around and see whether the misfires follow the packs or stay in the original cylinders. If they move, you have a bad coil pack or two. If they don't, since you've already changed plugs and wires, I'd see about having the injectors diagnosed to see if any of them are failing.

Jul 18, 2008 | 1999 Audi A6

Not finding what you are looking for?
2003 Dodge Durango Logo

Related Topics:

100 people viewed this question

Ask a Question

Usually answered in minutes!

Top Dodge Experts

yadayada
yadayada

Level 3 Expert

75797 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22114 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8152 Answers

Are you a Dodge Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...