Question about 2000 GMC Safari

1 Answer

Replaced resistor and relay still no high blower 0n 1994 safari

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • GMC Master
  • 3,640 Answers

Have you checked the switch!! or wires to resistor.

Posted on Oct 07, 2009

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Where is the heater fan relay on a Volvo 1994 850?


The blower motor relay is behind the glove box. If your blower only runs on high it's the resistor and it's behind the glove box too.

Jul 10, 2014 | 1994 Volvo 850

2 Answers

94 pontiac bonneville blower works in high speed only. Help?


Hope new bits were used not s/h. if new parts fitted check the multi plug fittings they have a habit of breaking wires in and around the plug a multi meter is helplul and a can of wurth sabesto 2040 penetrant spray a GOD send for all mechanics.

Mar 09, 2014 | 1994 Pontiac Bonneville

1 Answer

1994 chevy kodiak with Cat 3116. Heater/AC blower shuts down


you should make a diagnostic to know what happened to your car
of course you need an auto diagnostic tool : http://www.chinasnoy.comand you can find all kinds of tools in chinasinoy.com

May 21, 2013 | Cars & Trucks

3 Answers

What will make a blower in a car only work on high 0n a 1996 sunfire


you need to replace the resister block located on the duct work for the blower. it will be located near the blower (fan) with at least two wires plugged into it. remove the two or three screws hold it in and replace it. make sure it's off when you do that as the resistors get extremely hot.

robert

please take a moment to rate this solution thanks

Sep 07, 2009 | Pontiac Sunfire Cars & Trucks

1 Answer

I am tring to replace the blower resistor, can you tell me where it is located on my 1994 oldsmobile 98


The blower motor resistor is under the hood.On the back wall.You will see a plastic black panel and it should say fuses and relays.Remove the panel and there will be some fuses and relays.Below the relays and fuses you will find the resistor.There are 2 10mm nuts on each side of the relay center.Remove these and you will see the resistor connector.Remove the 2 screws and pull the resistor up.If your blower motor is not working.Before you replace the resistor try tapping on the blower motor while the system is on.If it comes on then the blower motor is bad.Good luck.

Jun 06, 2009 | 1994 Oldsmobile Eighty Eight

2 Answers

Blower motor problem!


Hope this helps....

2f26f00.png

Jan 28, 2009 | 2000 GMC Safari

3 Answers

94 gms safari van heater blower not working


I had the same problem in my 1994 safari. I thought it mite have been the resistor form other peoples comments. I removed it and tested it. The resistor was fine. The heater fan relay was bad, but I was able to repair it myself. If you remove it and inspect it there should be two contacts that need to make a good connection in order for it to work properly. When the fan is on high there is a little electro magnet that pulls the contact up and engages the fan motor to full speed. When it is not on high the lower part of the contact rests on the lower half of the relay flap. if there is not a clean connection at this location you are not sending signal to the resistor which controls the other three fan speed settings. Inspect this connection and if possible clean the contacts with emery cloth and make sure that the contacts are making a good connection. This should do the trick to make the lower speeds work if the resistor is still good. If this is too much brain damage try replacing the relay first and see what happens, if you are still getting the same result then the resistor or the fan switch is bad.

Good Luck!

Dec 23, 2008 | 1994 GMC Safari

1 Answer

My blower only works on high.


Under the hood there is a fuse panel with relays and fuses, but you may also need to replace the blower speed control resistor as the relay is working if it works on high.

Dec 22, 2008 | 1994 Plymouth Voyager

Not finding what you are looking for?
2000 GMC Safari Logo

Related Topics:

114 people viewed this question

Ask a Question

Usually answered in minutes!

Top GMC Experts

yadayada
yadayada

Level 3 Expert

75744 Answers

Freddy

Level 3 Expert

1311 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22114 Answers

Are you a GMC Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...