Question about 1999 Ford Taurus

Open Question

Ive replaced the fuel filter fuel pump coil pack spark plugs plug wires crank shaft sensor and checked all the fuses the car will turn over but will not start. any suggestions as what to try next

Posted by on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

honeymokey
  • 3113 Answers

SOURCE: my engine shuts off while im driving

Check ecm for number 1228253. If it has this one in it you will have a cutting off problem. Gm replaced these with #16198264 The cam sensor magnet on the cam gear will deteriorate and give problems. This will require removal of the timing cover.

Posted on Apr 17, 2009

roniecon
  • 6826 Answers

SOURCE: why is there No Spark in a 1991 Buick Lesabre

did u line the crankshaft sensor up? if not the sensor could have been damaged and the harmonic balance ,some models show a cam sensor ,check that,are u sure its not fuel related?

Posted on Jul 04, 2009

honeymokey
  • 3113 Answers

SOURCE: why is there No Spark in a 1991 Buick Lesabre

ECM would be the next part. Check the number on it . If it has the number 1228253 replace it anyway because they give a cutting off problem. Clean battery cables all three and replace bolts too.

Posted on Jul 06, 2009

dmftrucker
  • 1922 Answers

SOURCE: cranks and no spark no power at coil pack

i believe this line is fused from the E.C.M.,go to your local library and find a chilton's auto manual,this will tell you for sure

Posted on Aug 31, 2009

SOURCE: 1999 Lincoln continential will not start

I would first,change the spark plugs only if they were in the motor,say three years and 50,000. Not just to fix a misfire
Second you can only change a COP Coil, if you have a code or a way of knowing which one is bad. Again,why would you change all of them, when they all now work?
Crank Sensors rarely fail,so what test did you do to determine that was necessary?
Also.how would you know ,you had a missing coil, if you had no crank signal?
Now lets go from where you are now
Did you check fuel pressure,key-on ,eng off,with a pressure gauge?
Fuel filter fairly new?
Do you have all the ducting from the air cleaner to throttle body on and no vacuum leaks?
Do you have the MAF sensor connected. No signal,no start!!

Let me know what help you need

Posted on May 08, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I have a ford falcon 2002 xr6 ute with vct tickford motorist just stoped while driving gave a miss fire I have replaced crank sensor module coil fuel pump fuel filter still wont run running very ruf


On my falcon the same thing happened changed dizzy, coil even got new spark plugs what it turned out to be was auxiliary shaft that turns the dizzy or the dizzy module if you got coil packs. You can't see down the dizzy hole because its under the inlet manifold so take photo with your phone and you might see little bits of metal The auxiliary shaft teeth on the dizzy end where worn out and folding over so it can't give the proper spark at right time so went to wreckers 20 bucks for another. ford says it can't happen but I know quite a few engines with same problem

Dec 13, 2014 | Ford Cars & Trucks

1 Answer

My car will not start it cranks but will not turn on. So far I have changed the crank sensor I also have no spark to coil packs or spark plugs Fuel pump does not turn on when I turn the key. What is the...


Begin by checking fuses. Ignition, efi, fuel pump fuses. When key turned to on, do the warning lights and gauges work? That verifies switch has power and is sending power out. With key on, the coil primary wire to coil packs should have voltage.

No spark and no gas? Fuel pump fuse good? I think I would use a test light or multimeter to check that fuel pump fuse terminal has power to it with key on. If that's good, pull connector off at fuel tank and check for a voltage signal on fuel pump wire when the engine is cranking-if good signal, fuel pump needs taken out for replacement or inspection. If no signal check that fuel pump relay has power to it. With key off, pull the relay and check that one terminal has power to it-the feed wire for the pump. If no power signal at all, check maxi fuses or fusible links for a failure.

Sep 04, 2013 | Cars & Trucks

2 Answers

My 02 chevy cavalier turns over but will not start. I have replaced ever thing i know that could be wrong.


does it produce fire does the gas pressure rise does the crank sensor and cam sensor work

Feb 09, 2011 | Chevrolet Cavalier Cars & Trucks

1 Answer

Crank, won't start problem. I checked the spark plugs on Jeep 98. Looks good. Could it be the crank sensor or starter coil?


Yes it is very much possible.But there are many other possibilities too,including starter and spark plugs issue.

If your engine cranks normally but will not start because it has no spark, or it stalls and won't restart because it has no spark.

You can also do a test to confirm the problem .The procedure to do the test is as follows:---

If your engine has spark plug wires, disconnect one of the plug wires from a spark plug and place the end of the wire near a metal surface on the engine. Then insert a small Phillips screwdriver into the end of the wire (the plug boot), or a small bolt or nail to provide a conductive path. Then crank the engine and look for a spark to jump from the screwdriver, bolt or nail in the end of the plug wire to the engine. If you do not see a spark, there is an ignition problem.

OR-----------

If your engine has a coil-on-plug ignition system with no plug wires, In that case remove one of the coils from the spark plug and insert an old spark plug, a spark plug tester or a screwdriver into the end of the coil. Ground the spark plug or plug tester to the engine, then crank the engine and look for a spark. No spark indicates an ignition problem.If the engine has no spark, check for voltage at the coil positive terminal when the ignition key is on. If NO voltage, then problem is on the trigger side of the coil (pickup, crank sensor, ignition module or primary wiring circuit).

But If there is NO voltage at the coil itself, then in that case the problem is on the supply side (the ignition switch or ignition wiring circuit).-----------------

Jeep cranks but no start:----------------

A jeep that cranks over but doesn't start, in many cases will be due to a bad fuel pump, a broken timing belt, an inoperative cam sensor or crank sensor. Also these problems are related to faulty spark plug. Check the spark at spark plugs when you start the jeep. Do you notice any spark. Actually you should see. If in case there is no spark then it's a spark plug problem. Also the coil pack gives power to spark plug. So check the voltage at coil pack. It will show 12 volt. If there is no voltage noticed at coil pack then its faulty coil pack that has to be replaced. If all the possible options checked out ok then check the car starter. The starter gets power from battery to start the jeep. If the starter is faulty then it will not let the car to start. Also check and confirm that there is fuel in the jeep. If its very low fuel then in some cases this causes the problem. Also check and confirm that fuel pump is functioning properly and the fuel filter is not clogged. One of the easiest ways to check for a fuel pump related problem is to spray a little starting fluid into the air intake while trying to start the jeep. If the car starts momentarily, then there's a good chance the fuel pump is not working or the jeep is out of gas. You can also listen for the fuel pump's humming sound when the key is first turned on. Also if a inoperative fuel pump is suspected, a good technician will always check to verify there is power and ground being supplied to the pump, to eliminate the possibility of a bad relay or electrical issue. Fuel pressure can be checked with a pressure gauge and if there is pressure, pulse can be checked at the fuel injectors in several ways including the most common, with the use of noid lights. If the injectors don't have pulse the engine won't start. ---------- This troubleshooting tips will help you to solve the problem. Thanks. Helpmech.

Jan 07, 2011 | Jeep Cherokee Cars & Trucks

1 Answer

My '93 F250 5.8 l Automatic was turning over slowly when cranking to start. Replaced battery no change; Then after sitting for 2 mo. turning key to start produced only a click and dead gauges (battery...


The battery to starter connection has power.the battery is ok.but there are many other possibilities related to battery and its other connections,the spark plugs,the fuel pump,the fuel itself,the sensors(o2 sensor,maf sensor)the valve(IAC valve,egr valve). Most probably the spark plug,the coil pack and crank shaft sensor.This 3 are not getting power to get the car start.

There are some possibilities which you will have to check in this case:--

1) First of all check the power and voltage to the battery. With meter it will show exact 12 volt if the battery is charged. If the voltage is less get the battery charged at local auto repair shop. If the battery is internally drained and not getting charged then its time to replace the battery.

2) When you crank the car do you see spark coming at the spark plug? If no then its time to check the spark plugs and coil pack. If the spark plugs are not worn out and looks new then its time to check coil pack. The spark plug gets power to spark from coil pack.

3) The other thing to check in this case is the starter solenoid of the car. If the battery is charged and you start the car then it gives power to the starter to start the car. But if starter is faulty or not connected properly then car will not start.

4) The other thing to check in this case is fuel in the car. If there is fuel in the car then check the blockages in the fuel pump if the fuel pump looks proper then check the fuel filter above the fuel pump.

5) If all the above possibilities mentioned above checked out OK/perfect then it's a electrical issue and the wiring's in the car needs to be checked. The car gets power from the battery to get started. so the wires from battery needs to be checked one by one.



Thanks. keep updated for any more query.you can rate this solution and show your appreciation.

Sep 20, 2010 | 1993 Ford F250

1 Answer

Engine will turn over but will not start running


start with the basics check for fuel fire and air check fuel peressure with a gauge should be 50 - 65psi
pull spark plug wire and place near ground if no spark in crank sensor or coil pack ensure air filter is cleaned

on fuel pressure if low check fuel filter pump may be working and cant get to fuel rail but could have damaged pump the fuel pump is controlled via crank sensor signal so no crank sensor signal no fuel

Jan 15, 2010 | 1999 Plymouth Breeze

2 Answers

Continues cranking. Wont turn over. what s my next step?


You mean it cranks but wont start (cranking and turning over are the same thing) When cranking, rap on the fuel tank, if it then runs, the pump is bad and will need to be replaced.

Nov 15, 2009 | 1990 Oldsmobile Silhouette

1 Answer

RANDOM STARTING PROBLEMS; MOTOR SEEMS TO BE TURNING OVER FINE AND TRYS TO START; IF YOU WAIT AWHILE ALMOST ALWAYS START 1999 TIBURON


you may also have a plugged fuel filter if crank sensor and temp sensor turn out ok on the ohmmeter.
Next thing you will want to do is check for spark in each cylinder. You can pull one spark plug out, replug it back in to plug wire, lay on engine block, 1/4" form metal and the probe of plug, have someone else crank car, while you watch for spark. Then replace plug and wire and move on to then next. If you have one bad one, replace plug wire, if two or 3, it could be bad coil packs, if no spark, then it would be faulty module or crank sensor.

If spark is good, then you will want to check for fuel. You should have a fuel pressure test port on the fuel rail, with a rag, place over port, and press in valve to see if there is pressure. If no pressure, either fuel filter is plugged or fuel pressure regulator is faulty. As long as you can hear fuel pump turn on each time the ignition is placed in on position. If not, then relay or pump could be faulty.

Oct 08, 2009 | Hyundai Tiburon Cars & Trucks

2 Answers

Audi 100s 1993 cranks doesn,t start, turns over no start. when it starts runs rough and stalls.


could very well be a faulty sensor, leaky vaccum hose, bad coil packs, needing of new fuel filter, spark plugs, wires.

Have you checked your fuel pressure to make sure it is good. You can do this with fuel pressure tester on the fuel rail.

Also check every cylinder for spark
If you don't have any spark, or very weak spark, you could have bad coil pack, module, or crank sensor.

You can remove one plug at a time, and place it back on plug wire, place it on top of engine block, have someone else turn motor over well you observe to see if there is spark.

Do you have a service or check engine light on? If so, I would have the engine codes read to pinpoint exact problem area.

Let me know if you have any questions or need further help

Aug 26, 2009 | 1993 Audi 100

Not finding what you are looking for?
1999 Ford Taurus Logo

Related Topics:

31 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

75822 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

fordexpert

Level 3 Expert

5501 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...