Question about Chevrolet Suburban 1500

1 Answer

Adjusting timing on 1996 suburban 5.7l where is wire location for disconnect before adjusting?

Posted by on


1 Answer

  • Level 1:

    An expert who has achieved level 1.


    An expert who has answered 20 questions.


    An expert that hasĀ over 10 points.


    An expert whose answer gotĀ voted for 2 times.

  • Contributor
  • 24 Answers

This should be located close to the firewall on the drivers side close to the dist. It will be a brown or black single wire connector.

Posted on Oct 07, 2009


1 Suggested Answer

  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

A 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
The service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
Good luck!

Posted on Jan 02, 2017


Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

1 Answer

Where is the shifter solenoid found on a 1996 suburban

Most of the time it is built in in lock cable from ignition to shifter ,you could see it Under dash,2 wire came out off cable(i have see that on Cavalier should be similar,

Apr 23, 2014 | 1996 Chevrolet Suburban

1 Answer

95 chevy pick up 5,7L . have spark, have fuel, won't start?

how much feul pressure, it must maintain a certain amount if injected, or throtle body, try priming it ,and see if it helps, ( poor a little into inlet ) and check it , if it starts you need to check pump, or maybe just filter

Nov 17, 2012 | 1995 Chevrolet Suburban

1 Answer

Need wiring schematic blower motor fan switch 1996 suburban mexico build

We do not have any wiring diagrams, they are copyrighted by GM and not free to share. You can access them here:

Apr 26, 2012 | 1996 Chevrolet Suburban

2 Answers

Where is the wire located to stop automatic timing adjustment on a 1994 GMC 1500 5.7L

Hi:) There is a brown wire with a singal black connector in the wiring harness under the brake booster that goes up behind the engine on the drivers side to the distributor area.You disconnect this wire to disengage the computer timing auto adjustment. Set the timing to 0.deg and turn off engine before reconnecting brown wire. Computer will automaticly set the timing.

Feb 24, 2011 | 1994 GMC Suburban

1 Answer

Need to adjust the timing on my 94 chevy suburban 454 and it says to disconnect the wire before timing

Yours is located in the cab, on the passenger side, under the dash, right above the floor carpet. It's a single wire with a disconnect plug. It is the only single wire there. I believe it is grey, With a black plug.

Feb 17, 2011 | Chevrolet Suburban 2500 Cars & Trucks

2 Answers

My gas gauge on my 96 burb just fluctuates back and forth. Is this an easy fix? Its so annoying not knowing how much gas I have and trying to remember to reset the trip meter!

hi it soulds like it a wireing fault try looking at the sender unit located at the fuel tank it could be the supply feed of the earthing lead.

Apr 19, 2010 | 1996 Chevrolet Suburban

2 Answers

I have a 1996 Suburban that keeps blowing fuses on break lights

Check the turn signal flasher,and the trailer wire adapter that plugs in under the rear of the truck.Check the brake light switch,to see if it is grounding out on something.

Jan 03, 2010 | 1996 GMC Suburban

1 Answer

96 Suburban 5.7 hesitates and feels like it's dying

right to the left of the brake booster a one wire connector tan or brown must be disconnected prior to checking timing

Sep 12, 2009 | 1996 GMC Suburban

1 Answer

Transmission not shifting

Sounds like a speedo gear in the transmission ... I think the tahoe one had a speedo cable the speed sensor is located in the speedo ... will cause all those to fail if speedo is not working as did in my Astrovan

Apr 17, 2009 | Chevrolet Tahoe Cars & Trucks

2 Answers

1996 chevrolet suburban

The starter solenoid is connected to the starter. You will have to remove the starter and the solenoid the housing that the wiring is connected to. Good luck

Aug 23, 2008 | 1996 Chevrolet Suburban

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

86 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts


Level 3 Expert

78267 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22326 Answers

Ronny Bennett Sr.
Ronny Bennett Sr.

Level 3 Expert

6927 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides