Question about 2000 Pontiac Montana

1 Answer

Where is the trailer wiring harness connector in a 2000 pontiac montana? the instructions that came w/harness says it's a plug on the left/driver side. only thing I can find is the compressor for load leveling & a hand full of sires, but no connector...

Posted by on

Ad

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    MVP:

    An expert that gotĀ 5 achievements.

    Governor:

    An expert whose answer gotĀ voted for 20 times.

    Hot-Shot:

    An expert who has answered 20 questions.

  • Contributor
  • 44 Answers

It may be tapped in with another bundle of wires. Attached is a picture of the plug and location.where is the trailer wiring harness connector in a - 84108bd.jpg

Posted on Feb 03, 2010

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Is there an easy way to hook up my trailer lights to my montana?


Yes it costs about $30.00. Plugs right into the existing vehicle harness. Well worth the money, because what happens is some one messes the harness up and you bring it to me to repair. Usually around $100.00 by the time I solder all the wires back together and make it right. you can purchease these at the auto parts store.

Jul 31, 2011 | 2000 Pontiac Montana

1 Answer

Instructions for wiring a moving trailer connector


accessconnect_logo.jpg


Trailer Wiring Diagrams 4 Way Systems

4 way flat molded connectors allow basic hookup for three lighting functions; right turn signal / stop light (green), left turn signal / stop light (yellow), taillight / license / side marker (brown) and a ground (white).

4%20way%20wiring.jpg 4way_vehicle.jpg 4 way tow vehicle side.
4way_trailer.jpg 4 way trailer side.
5 Way Systems

Same as 4 way system listed above but adds a extra blue wire for brake signal or auxiliary power. Used on pop up camper trailers or utility / boat trailers.
5way_vehicle.jpg 5 way tow vehicle side.
5way_trailer.jpg 5 way trailer side.
6 Way System, Rectangle Plug 3/4 inch by 1 inch 6 way rectangle connectors right turn signal (green), left turn signal (yellow), taillight (brown), ground (white). The red and blue wire can be used for brake control or auxiliary. Use on a small motorcycle trailer, snowmobile trailer or utility trailer. Can also be used as custom wiring on trailers with 3 light/wire systems. See "Tow Vehicle Taillight Wiring" below.
6way_rectangle_1.jpg 6 way tow vehicle side.
6way_rectangle_2.jpg 6 way trailer side.
6 Way Systems, Round Plug

Round 1 1/4" diameter metal connector allows 1 or 2 additional wiring and lighting functions such as back up lights, auxiliary 12v power or electric brakes. Note: The black (sometimes red) 12v and blue electric brakes wire may need to be reversed to suit the trailer. Check with a test light or VOM. Uses: horse trailer, travel trailers, landscaping trailer, car trailer, etc.


6way_vehicle.jpg 6 way tow vehicle side.
6way_trailer.jpg 6 way trailer side.
7 Way Systems

Round 2" diameter connector allows additional pin for auxiliary 12 volt power or backup lights. Uses: heavy duty landscaping trailer, car trailer, boat trailers, horse trailer, travel trailer, construction trailer, etc. Check with a test light or VOM.


7way_vehicle.jpg 7 way RV flat blade tow vehicle side.
7way_trailer.jpg 7 way RV flat blade trailer side.

Jan 01, 2011 | 2001 Pontiac Montana

1 Answer

Were do you hook up the two wires under the hood for trailer brakes on a 2000 silverado


Sometime around 2000, GM started putting trailering pre-wire harnesses in the vehicle. Your truck may have this harness built in and would greatly simplify brake controller installation. Look under the glovebox and see if there is a wire harness tied off. There will be four wires in this harness, which should be run over to the steering column to use it. Most trailer brake controllers are compatible with this harness.
The four wires in the harness are: Red, 12vdc; black, ground; blue or purple, brake pedal; and brown or white, trailer brake wire to seven pin, four pin, or five pin connector at trailer hitch, if your truck came from the factory with a trailer hitch.
If you are adding the hitch and do not have the four wire harness, the under hood wires from your brake controller are Red, connect to one of the studs under the distribution box cover (the distribution box is on the driver's side against the firewall. Underneath the cover are two large threaded studs which are hot from the battery all the time); and the other wire from your brake controller would have to be run the length of the truck along the frame, tied off in several places, to the trailer hitch connector on the bumper. Follow the directions that came with trailer hitch wiring connector to connect this wire to the proper pin in the connector.
If this has helped you, great, and please remember to vote/comment.
Good luck!

Feb 21, 2010 | 2000 Chevrolet Silverado 1500

1 Answer

Have an extra connector and dont know where it plugs in at


purple and yellow should be crank sensor and it plugs into the coil pack on the drivers side closest to the firewall

Dec 14, 2009 | 2001 Pontiac Montana

1 Answer

I do not have power on the aux. terminal in the trailer plug on a 2008 dodge ram. Any ideas?


You have got 7 pin trailer connector that was included in the optional trailer tow package. This trailer tow package also includes an electric trailer brake wiring provision that terminates at a connector located on top of the large body harness connection under the instrument panel to the left of the break pedal, as well as an electric trailer brake pigtail harness and an instruction card that are stored in the glove box when the vehicle is shipped from the factory. You will need to add an electric brake controller of your choice that will plug-in to the harness and that will also give you power on your auxiliary circuit.

Oct 04, 2009 | 2008 Dodge Ram Pickup 2500

2 Answers

2000 montana brakes shutter and the abs light and


i had the same problem on my 2000 montana, used a scanner to check for abs code and found right front sensor throwing code, checked sensor and found ok, checked harness from sensor to connection under hood and found wiring circut at the plastic clip where harness hooks to sensor was bad, replaced harness from connector to sensor and problem went away

Apr 20, 2009 | 2000 Pontiac Montana

1 Answer

Trying to find the wiring for a tow pckg in a 2000 montana


the harness is there you need the plug that goes from the factory plug to the kind of plug you need for your trailer. the harness is wrapped around the wires for the rear tail lamps

Apr 09, 2009 | 2001 Pontiac Montana

2 Answers

Brake lights quit working


Tail lights acting insane?

We had the same issue with our 2000 Pontiac Montana. Brake lights, turn signal lights, running lights, back-up lights and emergency flasher didn’t work at all or operated at random. The cause: poorly designed aluminum contacts on the tail light circuit board and wiring harness connector arced over and disintegrated with normal use.

Pull the tail lamp assembly, remove the electrical connector and look for burned contacts on the connector plug and the connector socket (they call this long plastic piece with the socket the circuit board: it includes the four bulb sockets. Replace the circuit board and the wiring connector.

You can DIY this job with basic auto mechanical/electrical skills and tools. The two circuit boards and the two connectors set me back $230 (2009 cost) for new parts. The electrical contacts on the factory replacement parts are improved.

I needed a T-30 torx driver to remove the tail light assembly (you need this to change out bulbs, too), wire cutters, wire strippers, electrical tape and an electrical lug crimper to do the job.

Aug 02, 2008 | 2003 Pontiac Montana

Not finding what you are looking for?
2000 Pontiac Montana Logo

452 people viewed this question

Ask a Question

Usually answered in minutes!

Top Pontiac Experts

yadayada
yadayada

Level 3 Expert

76051 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8265 Answers

Are you a Pontiac Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...