Question about 2005 Honda Pilot

1 Answer

I need instructions to program a remote transmitter for my 2005 Honda Pilot. I bought a new key today because the transmitter was dead in the original but I couldn't afford the $100 charge to program it, as I'm a freshly unemployed single mother. Help!

Posted by on

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that gotĀ 5 achievements.

    Governor:

    An expert whose answer gotĀ voted for 20 times.

    Hot-Shot:

    An expert who has answered 20 questions.

  • Expert
  • 116 Answers

You have to have the dealership program the vehicle to the transmitter, You can replace the batteries in the old one you just have to pry it open at the seam, may be difficult but can be less expensive.

Posted on Oct 07, 2009

Testimonial: "Not helpful at all. I need instructions to program the new transmitter key. The battery was not the problem in the old one. "

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

Why won't it start?


Honda Pilot 2005 won't start dead starter - YouTube

? 2:48
https://www.youtube.com/watch?v=tH2rEYLbQrY
Sep 15, 2011 - Uploaded by Alexey Gavrilov
Honda Pilot 2005 won't start dead starter ... How To Replace a Starter 2006 Honda Odyssey -EricTheCarGuy ...

Today my Pilot won't start! - Honda Pilot - Honda Pilot Forums

www.piloteers.org > ... > General > Problems
Mar 13, 2011 - A half-hour later, I got in to move it back, and the Pilot would not start. All the .... Most original batterys from 2005 need to be replaced by now. Starting Problem 2005 EX
Feb 24, 2011
Cold Weather (0 deg F) 06 Pilot won't start after jump - Honda ...
Jan 17, 2009
Engine won't start - clicking sounds and guage flutter - Honda ...
Dec 23, 2007
Starting Problems
Mar 24, 2006
More results from www.piloteers.org

Thread: '05 EXL won't start - HondaSUV.com Forums



Jan 01, 2016 | 2005 Honda Pilot

2 Answers

How can I program my remote?


Remote for ? door unlock / lock , remote start , garage door opener .
If the door lock / unlock , panic alarm ,remote start . You can't dealer only . Need a factory scan tool .
Transmitter Programming
Important: Up to 4 transmitters can be programmed. Do not operate or program the transmitters in the vicinity of other vehicles that are in the keyless entry program mode. This prevents the programming of the transmitters to the incorrect vehicle. The order in which the transmitters are programmed is important. The first transmitter programmed will be transmitter #1, and the second transmitter programmed will be transmitter #2. Use care to program the transmitters correctly.
The scan tool must stay connected until all of the transmitters are programmed.

Invalidate All
This procedure will erase all keyless entry transmitters from memory.
Install a scan tool.
Turn ON the ignition with the engine OFF.
With the scan tool, select Body.
Select Remote Control Door Lock Receiver (RCDLR).
Select Module Setup.
Select Program Key Fobs.
Select Invalidate All Fobs.
Follow the scan tool on screen instructions.
Transmitter Slot Programming
Transmitter slot programming allows a single transmitter to be programmed into a specific slot without affecting any of the other programmed transmitters. By using slot programming, the transmitter originally programmed to a specific slot is erased and the new transmitter learned in its placed.
Install a scan tool.
Turn ON the ignition with the engine OFF.
With the scan tool, select Body.
Select Remote Control Door Lock Receiver (RCDLR).
Select Module Setup.
Select Program Key Fobs.
Select the key fob desired to be programmed.
Follow the scan tool on screen instructions.
Remove the scan tool.
Exit the vehicle. Operate all functions on transmitters to verify correct system operation.

Jun 05, 2015 | 2007 Buick LaCrosse CXL Sedan

1 Answer

How can I program a key fob


GRAND PRIX KEY FOB PROGRAMMING INSTRUCTIONS Transmitter Programming No Tools Required In the event that a transmitter is lost, program the old and the new transmitters into the memory of the remote control door lock receiver.Up to 4 transmitters may be programmed Important Once the keyless entry receiver enters the programming/diagnostic mode, the programming of the first transmitter erases all previous transmitter programming information. You must then program all of the transmitters Program only 1 vehicle remote control door lock receiver at a time. If you program multiple receivers simultaneously, the same transmitter could possibly be programmed to more than 1 remote control door lock receiver

Apr 22, 2013 | 2001 Pontiac Grand Am SE

1 Answer

2005 saturn relay fob programming


TRANSMITTER PROGRAMMING
IMPORTANT: All transmitters which are to be recognized by the remote control door
lock receiver (RCDLR) must be programmed in a single programming
sequence. If the system is placed in program mode it will erase all
previously programmed transmitters upon the receipt of the
programming signal from the first transmitter. Up to 4 transmitters can
be programmed. Do not operate or program the transmitters in the
vicinity of other vehicles that are in the keyless entry program mode.
This prevents the programming of the transmitters to the incorrect
vehicle.
Install 1. a scan tool.
Use the scan tool in order to access the Body Control Module (BCM) Special Function or
Module Setup: Program Key Fobs.
2.
3. Press the START soft key on the scan tool.
IMPORTANT: The scan tool must stay connected until all of the transmitters are
programmed.
Press and hold the LOCK button and the UNLOCK button simultaneously on one transmitter.
After a delay of 5-10 seconds, the scan tool will indicate that the transmitter is programmed.
4.
5. Repeat the previous step in order to program up to 4 transmitters.
6. Remove the scan tool.
7. Operate the transmitter functions in order to verify correct system operation.

Sep 14, 2012 | 2005 Pontiac G6

2 Answers

2003 remote control for 2005 van?


Transmitter Programming
If you lose a transmitter, program the old and new transmitter(s) into the remote control door lock receiver's memory. Up to 4 transmitters may be programmed.


Important
Once the remote control door lock receiver enters the programming/diagnostic mode, the programming of the first transmitter erases all previous transmitter programming information, requiring the programming of all transmitters.

Program only 1 vehicle remote control door lock receiver at a time. If more than 1 receiver is being programmed at the same time, it is possible that the same transmitter could be programmed to more than 1 remote control door lock receiver.


Perform the following steps in order to program the transmitter:

Remove the ignition key from the ignition lock cylinder.
Remove the BCM PRGRM fuse from the fuse panel. Refer to Fuse Block in Wiring Systems.
Close all of the doors.
Close the liftgate.
Turn the ignition lock cylinder to ACC.
Turn the ignition lock cylinder to OFF, and then back to ACC within 1 second.
Open and close any vehicle door. A chime will be heard when the system enters the BCM programming/diagnostic mode.

Important
After 7 seconds, a chime may be heard confirming successful synchronization. It is necessary to wait approximately 14 seconds for a second chime that will confirm successful programming.


Press and hold the transmitter LOCK and UNLOCK buttons simultaneously for 14 seconds.
Repeat the previous step on each additional transmitter to be programmed.
Remove the ignition key from the ignition lock cylinder.
Install the BCM PRGRM fuse back into the fuse panel. Refer to Fuse Block in Wiring Systems. IF THIS WAS HELPFUL,PLEASE RATE,THANK YOU

Jul 15, 2010 | 2005 Pontiac Montana

1 Answer

2003 honda pilot, remote control doesn't work even with new battery , light on remote control doesn't blink


did the light blink when it worked? It may need to b reprogrammed. check the owners manual, it should tell you how to program. If the fob is dead, check ebay for a new one, usually 50 bucks and the reprogram

Dec 06, 2009 | 2003 Honda Pilot

1 Answer

Keyless remote wont work


try to reprogram the remotes using these instructions..........
i assume for 02 explorer not th 05 frestyle listed (although similar procedure)
Remote Transmitter Programming NOTE: All remote transmitters are programmable and must be set at the same time.
  1. Make sure that the anti-theft system is not armed or triggered and key code programming is not active.
  1. Open the door, then press the driver door lock control switch UNLOCK button.
  1. Turn the key from OFF to ON 8 times within 10 seconds, with the eighth turn ending in ON. If the program mode is sucessfully entered the doors will lock and unlock to confirm.
  1. Press any button on a remote transmitter, and the doors will lock and then unlock all doors to confirm that the remote transmitter is programmed. All remote transmitters must be programmed within 20 seconds of each other. Up to four remote transmitters can be programmed to the vehicles security module each time programming mode is entered.
  1. If the door locks do not respond for any remote transmitter, wait several seconds and press the button again. If the door locks still fail to respond, refer to Locks, Latches and Entry Systems — Late Build or Locks, Latches and Entry Systems — Early Build in this section.
  1. NOTE: Exiting is acknowledged by locking and unlocking the doors if at least one remote transmitter has been programmed.
    Exiting the programming mode is accomplished if one of the following has occurred:
    • The key transitions to OFF.
    • 20 seconds have passed since entering programming mode or since the last remote transmitter was programmed.
    • Four remote transmitters have been programmed.

Jun 02, 2009 | 2005 Ford Freestyle

1 Answer

Need the procedure to program my new remote...THANKS!!!


1. Close all vehicle doors.

2. Insert the key into the ignition.
3. Hold down the power UNLOCK button on the driver’s door panel-continue to hold
down until instructed to release in step 9.

4. Perform steps 5 through 8 in fairly rapid succession.
5. Turn the ignition switch to the ON position (as far as you can go without starting the
engine).

6. Turn the ignition switch to the OFF position.
7. Turn the ignition switch to the ON position.
8. Turn the ignition switch to the OFF position.
9. Release the power unlock button on the door panel. The vehicle will lock and unlock
the doors automatically.

10. Hold down the LOCK and UNLOCK buttons on the transmitter simultaneously until
the door locks and unlocks.
This step may take up to 30 seconds.

11. Repeat step 10 NOW for each additional transmitter (including any existing
transmitters).

12. Turn the ignition switch to the ON position in order to exit the transmitter programming
mode.

May 20, 2009 | 2005 Chevrolet Silverado

4 Answers

How do I program my new Suzuki keyless entry remote to work with our new SUV?


I bought a remote the other day and got these instructions with it. They worked!

1. Make sure vehicle is in Park
2. Press Vehicle Information button (has the icon of a car and an 'i')until 'PRESS *check mark* TO RELEARN REMOTE KEY' displays.
3. Press set/reset button. The message 'REMOTE KEY LEARNING ACTIVE' will display.
4. Press and hold the lock and unlock buttons on the transmitter at the same time for about 15 seconds. A beep will sound indicating that the transmitter is matched.
5. To match additional transmitters at this time, repeat Step 3. Each vehicle can have a maximum of four transmitters matched to it.
6. To exit the program mode, you must cycle the key to LOCK.

Jul 20, 2008 | 2007 Suzuki XL-7

Not finding what you are looking for?
2005 Honda Pilot Logo

440 people viewed this question

Ask a Question

Usually answered in minutes!

Top Honda Experts

yadayada
yadayada

Level 3 Expert

75807 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22133 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8172 Answers

Are you a Honda Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...