Question about 2000 Ford Contour

1 Answer

I NEED TO SWAP THE ENGINE IN MY 2000 CONTOUR. I HAVE THE VCT 4-CYL, CAN I USE THE ZETEC 4-CYL WITH A PCM SWAP?

Posted by on

Ad

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    Hot-Shot:

    An expert who has answered 20 questions.

    Corporal:

    An expert that hasĀ over 10 points.

    Mayor:

    An expert whose answer gotĀ voted for 2 times.

  • Expert
  • 56 Answers

I dont think thats impossible....if theres a will theres a way.....just be sure u know wat your doing...

Posted on Oct 07, 2009

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

09 accent cyl 4 missfire, plug injetor coil all ok cyl comp test all within spec. changed pcm old one stopped workin alltogether. all no change,intermittent missfire


SWAP COIL LIKE FROM CYL NUMBER 1 TO 4 AND ROAD TEST UNDER LOADS IF CHANGE THE MISS TO CYL NUMBER 1 NEED A COIL OR BAD PLUG AT CYL NUMBER 4

Sep 02, 2014 | Cars & Trucks

1 Answer

Where reclaim port is located & how to remove used fliud from 2000 ford contour se 4 cyl.


The ac fluid(gas ) never gets old as it is a gas . The oil never oxidises as there is no air in the system so it never needs replacing. Most problems with ac units come from leaks and owner interference ( replacing gas that doesn't need replacing) or over filling with the wrong gas or just not understanding how and why it all works.

May 25, 2014 | 2000 Ford Contour

1 Answer

I cant find the EGR valve on my 1998 Ford Contour SE. Supposed to be on the intake manifold but I dont see it anywhere. Also should be a line to it from the exhuast manifold but I dont see one. Engine is...


It has to have a tube or pipe going to it
from the exhaust manifold

It has to have vacuum hoses going to it
That is a dead give away

It could have a wiring harness connected to it.

As you said it has to let exhaust gases into the intake

Look for a picture on the internet or ask a neighbor
to show you

Jun 27, 2011 | 1998 Ford Contour

2 Answers

How do you replace the spark plugs with oil around the tops of the plugs. it;s a 4 cyl - 16 valve Zetec VCT


Take a thin cloth or napkin and absorb the oil, you may have to use a screwdriver or ? to push the cloth down beside the plug.

Jun 29, 2010 | 1998 Ford Escort

1 Answer

What type of engine oil for 1.6 focus zetec 2003


2003 FORD FOCUS 2.0L 4-cyl Engine Code [3]
Engine Oil Grade 1......API* All TEMPS......SAE 5W-20, Engine, with new oil filter 4.3 liters.
Thank you for using fixya and good luck Oil Drain Plug.....17ft/lbs Torque

Apr 27, 2010 | 2003 Ford Focus

1 Answer

Where is the thermostat on a 2000 ford contour 4 cyl 2.0L


Follow the upper radiator hose to where it meets with the engine block.
Where it attaches, is the thermostat housing. Should have 3 bolts on it. The thermostat is underneath the housing.

Nov 25, 2009 | 2000 Ford Contour

1 Answer

Help 95 ford contour obd-1 error 335


I was reading in one of my repair manuals and it says in there that there could be a block where the exhaust gas pressure sensor is. There could be a blocked inlet hose. Or it could be the ECM.

Sep 10, 2009 | 1995 Ford Contour

1 Answer

Where is the ignition module located on the 1996 ford contour?


tragik nc: In looking this car up in both the 4 and 6 cyl configurations, Ford said that the ignition control module is no longer a separate component. It is actually integrated into the PCM (power control module)
This is located in the right rear corner of the engine compartment behind the power steering reservoir.
Good Luck, mybunkey>>>>>>>>>>>>>>>>>

Apr 20, 2009 | 1996 Ford Contour

Not finding what you are looking for?
2000 Ford Contour Logo

Related Topics:

89 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

76164 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

fordexpert

Level 3 Expert

5522 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...