Question about 2003 Chevrolet Silverado 2500HD

1 Answer

Thanks..but the flashers, bulbs and sockets are all good...a friend mentioned the flasher assy. on the column? no idea about that...any suggestions?

Posted by on

  • mikey3965 Oct 07, 2009

    everything works normal except those two brake lights

  • mikey3965 Oct 07, 2009

    Can anyone help me with this? I'm sure to get a ticket eventually because I travel alot!

×

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that gotĀ 5 achievements.

    Governor:

    An expert whose answer gotĀ voted for 20 times.

    Hot-Shot:

    An expert who has answered 20 questions.

  • Expert
  • 136 Answers

Pull your emergincy flashers on, on your sterring column if they don`t flash you have a burned out bulb somewhere in turn signal lights front or rear

Posted on Oct 07, 2009

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Where is on 1987 pontiac 6000 are the bulbs for turn signals How do I get to them? & or the flasher ? Is it in the fuse box?


The turn signals at the rear share the same bulb, same filament on the bulb even, as the brake lights. So if you have brake lights, the rear turn signal bulbs are good. If I recall, you access the rear bulbs from inside the trunk, and pretty easy to change bulbs. Look for a panel or trim piece in the trunk that covers the light bulb assemblies. You turn the bulb sockets a quarter turn counter-clockwise and pull them out, then you can replace the bulbs. They are two filament bulbs-one filament for the park lights (tail lights) and one filament that serves for brakes and turn signals together.
The flasher unit is a small round cylinder, I don't believe it was in the fuse box, but located up under the dash, close to the steering column. The hazard flasher unit was also up under there and looks the same. Look for them on a bracket near or by the steering column, possibly one on each side of the steering column To find the turn flasher, turn your hazard switch on. The little round unit that is clicking-you may hear it or feel it click with your finger on it-is the hazard flasher. The turn flasher will be the one that is not clicking. A little round cylinder is how you identify it.

Jun 03, 2014 | Cars & Trucks

2 Answers

Turn signal flashes fast but bulbs good


Under the dashboard there is a round metal device called a flasher its where the tick noise comes from when you activate your turn signal I would try replacing that next Good luck

Apr 04, 2014 | Toyota Camry Cars & Trucks

1 Answer

Right front side turn signal does not work replaced all bulbs and checked fuses headlight flashers work when hazards are on front to back except driverside turn signal ,in dash right stays solid left


I don't believe it would be a bad ground for just one light. It could be a wire, a socket connector, or the bulb socket itself. See if the wire has power at the socket when signaling left, with key on. If there is power, probably a bad socket or connector. If no power, check for power coming from flasher-the wire going to front left, or driver's side. If you have power from the flasher, but nothing at the socket, the wire has probably broken.
Good luck.

Feb 06, 2013 | Cars & Trucks

2 Answers

My left turn signal works but it wont blink which fuse is it? or is it something els?


It sounds like the flasher relay is stuck closed. It is located under the left side of the dash, to the right side of the steering column. Try replacing that and double check if you recently replaced any bulbs that they have the correct base for the sockets. Sometimes the bulb might look right but the base is slightly different. The correct turn signal bulb for your vehicle is a 2057, and an EL12 or FL12 for the flasher relay.

Mar 15, 2011 | 1995 Chevrolet Beretta

2 Answers

Turn signals don't flash, they just go on solid


You may have a bad socket or bulb either in the front or rear replace if you find the one that is not working. May also be your flasher hit your emergency flashers and if those do not work suspect the flasher.

Oct 11, 2010 | 2004 Chevrolet Impala

2 Answers

Turn signals dont work bulbs/fuses are good.


check to see if the emergency flashers work if they do its its either a wiring problem, bulb, or socket the bulb fits in. if it does not work than the flasher is the problem. it is located underdash on driver side in the kick panel( to left of the brake pedal) it is a blue or grey sguare relay looking plug. if it is factory flasher it will say flasher with the part # on it. it should also say toyota on it. good luck

Jul 09, 2009 | 2000 Toyota Camry

3 Answers

Signal lights work intermittently


For an intermittant problem I'd recommend removing the flasher unit -- it is plugged into a socket, so you can just pull it out.

Clean the contact pins on the flasher and replace it in the socket.

That should do the trick.

May 27, 2009 | 2000 Oldsmobile Intrigue

1 Answer

The 1997 dodge dakota turn signal problem.


Check the back side of the interior fuse box, should be between the steering column and the fuse box, some where on the box itself.

Dec 09, 2008 | 1997 Dodge Dakota

2 Answers

Left Tun Signal Flasher. .


chances are it is a loose socket or wire going to the socket it. to check this just turn the signal on and wiggle it this should help you find a loose wire or if the connectoer is bad

Sep 01, 2008 | 2001 Buick Century

2 Answers

1988 ford Mustang 2.3L


your turn sig switch in the steering column is probably worn out and needs to be replaced, have a steering column specialist come out and fix or go to the dealer.

Jul 29, 2008 | 1987 Ford Mustang

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

82 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts

yadayada
yadayada

Level 3 Expert

75077 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

7768 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...