Question about 1994 Chevrolet Corsica

1 Answer

Instructions of what to remove to replace the thermostat on my sons 1994 Corsica 3.1 L engine. I believe I just un do the air intake, the braket, the throttle mixing device and then the protector for the exhaust pipe. Please confirm if you have replaced one before. Home mechanic.

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    President:

    An expert whose answer got voted for 500 times.

  • Master
  • 678 Answers

Sounds like your well on your way. A few tips that may help you along the way. Usually the bottom bolt hole in the thermostat housing is slotted so you don't have to fully remove it. Which should save you a headache trying to get it back in. Also be very careful with those bolts, spray some penetrating oil down there a few times before you go at it. If they break you'll find yourself in a world of misery. Good luck.

Posted on Oct 07, 2009

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Need to see where the thermostat is located on 1994 chevrolet corsica


a simple way to find the thermostat on any vehicle, is to follow the upper radiator hose to the engine. Where the hose clamps to the engine has 2 maybe 3 bolts holding it on. Take out the bolts and the thermostat will be inside. be aware that coolant will leak out, and only do this when the engine is completely cool.

Jan 04, 2012 | 1994 Chevrolet Corsica

1 Answer

Replace themostst


Hello ,

The thermostat is located on the right side of the engine looking in,between the intake manifold and the air filter box, underneath the wiring. This is in a 1994 Ford Probe GT 6 cylinder.

To replace the thermostat, you really need to remove the intake manifold and this can be up to two or three hours work alone, even for a qualified mechanic.

It is in the housing at the engine end of the upper rad hose. When replacing it make sure the spring on the thermostat is toward the engine.

NOTE: Remove the air intake box so you can see below. There is a pipe running right into the bell housing where the thermostat is housed. There is one bolt that you need to remove (it is to the right,below the distributor) Then there are the other 12 mm bolts on the bell of the thermostat housing to remove. After removing those the thermostat should be able to come right out.

Thank you, hope this helps you out.
Bill
mr1bill_1.jpeg.

Aug 07, 2011 | 1994 Ford Probe

1 Answer

Hi, I'm trying to replace the thermostat on my 1997 Mercury Grand Marquis. I'm kind of stuck because to drive it anywhere for repair will overheat the engine and my friend informed me that it's...


Okay....this is for the 4.6L engine....then I'll post for the 5.0L and 5.8L....not sure which one you have....and please don't forget to rate! Thanks a mill!!!!


  1. Drain the cooling system to a level below the thermostat.
    1. Disconnect the upper radiator hose from the thermostat housing.
    2. Remove the 2 thermostat housing retaining bolts and remove the thermostat housing.
    3. Remove the thermostat and O-ring seal. Inspect the O-ring for damage and replace, as necessary.
  2. To install:

    1. Make sure all mating surfaces are clean.
    2. Install the thermostat, O-ring and thermostat housing. Make sure the thermostat is positioned in the 3 o'clock position.
    3. Install and alternately tighten the thermostat housing retaining bolts to 15-22 ft. lbs. (20-30 Nm). Connect the upper radiator hose.
    4. Fill the cooling system


c17hydro_163.gif

Remove the thermostat housing bolts and ...



c17hydro_164.gif

... remove the housing from the intake manifold



c17hydro_165.gif

... remove the thermostat from the intake manifold



c17hydro_166.gif

Thoroughly clean the thermostat mounting surface before installing a new thermostat



c17hydro_167.gif

Always replace the thermostat O-ring with a new one



c17hydro_168.gif

Make sure that the air valve is positioned in the 3 O'clock position after the thermostat is installed

May 07, 2011 | 1997 Mercury Grand Marquis

1 Answer

Where is the thermostat?


It's located under the ignition coil pack.

Follow these instructions to replace the thermostat

  1. Disconnect the negative battery cable.
  2. Drain the cooling system.
  3. Remove the air intake tube, crankcase breather and PCV hose.
  4. Remove the ignition coil pack and bracket.
  5. Remove the upper radiator hose.
  6. Remove the ignition coil pack bracket.
  7. Unfasten the heater hose inlet tube bracket bolt and remove the heater hose inlet tube from the thermostat housing.
  8. Remove the three thermostat housing attaching bolts, then remove the thermostat housing and gasket.

Mar 06, 2011 | 1994 Ford Escort

1 Answer

Need to see where thermostate is located have an idea but am not sure where it is the year is 1996 corsica 2.2liter v4


GM Corsica/Beretta 1988-1996 Repair Guide
The thermostat is located inside a housing on the back of the cylinder head. It is not necessary to remove the radiator hose from the thermostat housing when removing the thermostat.

CAUTION When draining the coolant, keep in mind that cats and dogs are attracted by ethylene glycol antifreeze, and are quite likely to drink any that is left in an uncovered container or in puddles on the ground. This will prove fatal in sufficient quantity. Always drain the coolant into a sealable container. Coolant should be reused unless it is contaminated or several years old.

ef45c14.jpg


Fig. 1: Exploded view of the thermostat and housing assemblies - 2.0L and 2.2L engines


258dbdd.jpg


Fig. 3: On 1994 2.3L engines, the thermostat is located in the radiator outlet pipe

e05e11c.jpg
7c859c6.jpg

Fig. 4: Exploded view of the thermostat and water outlet - 2.2L and 3.1L (VIN T) engines


78055db.jpg


Fig. 5: Thermostat and coolant outlet mounting - 3.1L (VIN M) engine


I hope help you (remember rated this) Good luck.


Fig. 2: Exploded view of the thermostat, housing and related components -1990-93 2.3L engines

Sep 22, 2010 | 1996 Chevrolet Corsica

2 Answers

Coolant leak at intake 1994 Buick LeSabre 3.8 ltr


There are several areas of possible leakage. One is the hose and plastic outlet from the intake manifold on the passenger side of the engine. The hose runs low, underneath the alternator. The plastic outlet cracks, the hose gets old, the clamps on the hose can also be loose. The replacement outlet from the dealer is steel, not plastic.
Another possibility for leakage is on the driver's side of the intake manifold. Underneath the air inlet is a metal cover on the end of the intake manifold. This covers the coolant passages at the end of the intake. Mine was oozing antifreeze..you don't have to pull the intake to replace this.
The other place for leaks is the intake itself..requiring removal of the intake. I've done this...I don't think it is that bad of a job. However, if you put in a new intake, don't forget to put in a pcv valve..it fits under a small cover at the right rear of the intake manifold.

Nov 21, 2009 | 1994 Buick LeSabre

1 Answer

Replacing thermostat in 95 oldsmobile cutlass


Follow the top radiator hose UNTIL it reach a metal neck-like- thing.Disconnect to hose Follow the neck to where it connects to the thermostat casing. Un screw the two bolts and and remove the thermostat from the casing.. You'll have to remove the air intake

Drain about 1 gallon of coolant from radiator Follow upper radiator hose to engine housing Remove 2 bolts on housing--make note how thermostat is installed Clean both surfaces completely Install new gasket and thermostat Tighten both bolts evenly and securely Re-fill radiator slowly to prevent "airlock" Check for leaks Start engine with heater on Run to normal operating temp Check coolant level

Nov 04, 2009 | 1994 Oldsmobile Cutlass Supreme

2 Answers

I wanted to change my thermostat in my 93 chevy corsica but do not know where it is located


follow your upper radiator hose from the radiator back to the engine it will be under the housing hose connects to

Aug 10, 2009 | 1993 Chevrolet Corsica

Not finding what you are looking for?
1994 Chevrolet Corsica Logo

Related Topics:

115 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts

yadayada
yadayada

Level 3 Expert

75197 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

7782 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...