Question about 1996 Ford Explorer

2 Answers

The fuel pump was replaced. Now the odometer doesn't work

Posted by on

2 Answers

  • Level 1:

    An expert who has achieved level 1.

    Problem Solver:

    An expert who has answered 5 questions.

  • Contributor
  • 3 Answers

I think you may need a new odometer as well,

Posted on Oct 07, 2009

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that gotĀ 5 achievements.

    Governor:

    An expert whose answer gotĀ voted for 20 times.

    Hot-Shot:

    An expert who has answered 20 questions.

  • Expert
  • 89 Answers

Check the wiring to the vehicle speed sensor.The wire harness is right near were they worked on the fuel tank,at the rear of the trans.

Posted on Oct 07, 2009

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Gas gauge shows full then a few seconds later shows empty when I start the car.


REMOVE THE WHOLE PACKAGE AND SWITCH IGNITION ON AND TRY TO FIX CONNECTION AND CHECK IT OUT. MOVE FLOATER AND SEE WHAT YOU GET

Aug 24, 2015 | 1998 Buick Century

1 Answer

How do I fix my gauges? (Ie, gas gauge, temp gauge, speedometer, odometer)


Fuses? Blown fusible link? Most gauges work by getting 12 volts from the ignition switch when on, and getting a ground from the sender. Often the 12 volt supply wire goes to more than one so if dead, both will fail. If you have a wiring diagram, you might find which wire to cluster should be hot, and trace it backward to find the issue. Easier to check for ignition switch feed first.

Jul 01, 2015 | Cars & Trucks

2 Answers

I have ford bantam 1.6i rocam 2006 model. It Doesn't start, It doesn't pump the petrol, the is no power to fuel pump


Refer to your manual there is a switch that deactivated the fuel pump in case of accident, there is a switch by the pasangers feet that if in the up position is activated to stop the fuel...

Aug 28, 2012 | 2006 Ford Bantam 1.6i

1 Answer

1995 thunderbird fuel gauge not working and inside lights stay on.


The gauge In the dash is electronic and the gauge could be bad. My odometer doesn't work but seedo does found that its all electronic

Jul 30, 2012 | 1995 Ford Thunderbird

1 Answer

2000 jeep wrangler won't start, good crank, no bus


Check fuses first, but could be needs new CPU

Jun 14, 2012 | 2000 Jeep Wrangler

1 Answer

Old old Ford F250(1978), horn doesn't work, neither does gas or odometer (but I'm looking for fixes for the horn)


Chances are the horn is burnt out, the gas gauge will require a new fuel tank gas gauge sending unit and the odometer will require the speedomenter be removed and sent out for repair, the little gear drive for the odometer is broken

May 18, 2011 | Ford F-250 Cars & Trucks

1 Answer

Starts and runs but dies in about a minute think it may be fuel pump also the odometer says no pump 01 dakota 4cylinder 81,000miles


Hi.

Before replacing the pump, test the pump thoroughly. The symptoms you are describing are often caused by a PCM problem (odometer to zero, fuel pump warning, sometimes "No Bus" P16xx OBD code doing code scanning and CEL warning).

THe PCM is the main computer module, and among other things send power and data to odometer through a data connection called BUS, and controls the pump.
The pump can be tested energizing it directly and checking if it works without problem for a while. There is no need for testing fuel pressure because the problem is electrical.
If the pump is OK, then problem is PCM.

The PCM is expensive (about $800). The replacement is not expensive (one hour garage or so). The PCM is under warranty for the first 80K miles and 8 years. Since the warranty on the part is just over, I suggest talking to your local dealer before starting any repair or before replacing any part.

If you haven't done it yet, do also an OBDII code scanning. If you drive to the nearest Autozone you can scan the PCM for error codes free of charge.

Here one of the several discussion pages on the problem available online.

Regards.

Ginko.

Jan 02, 2011 | Dodge Dakota Cars & Trucks

3 Answers

Speedometer, gas gauge, odometer, rpm gauge not working


My gas guage, speed odometer and tempiture does not work
The speed odometre is reading 9999999 what should i do

Jul 29, 2009 | 1998 Nissan Frontier

1 Answer

Gas Gauge and Odometer Broken


yeah replace the odomitor cable that should hook into the side of the trans by the fire wall. also check the fuel tank float and fuel pump

Jun 08, 2009 | 1993 Saturn SL2

Not finding what you are looking for?
1996 Ford Explorer Logo

79 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

75117 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

fordexpert

Level 3 Expert

5474 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...