Question about Ford Bronco II

1 Answer

How to replace the front brake hose on an 84 ford

How to replace the front right brake hose in a 1984 ford bronco 2. Have the part just don't know how to install it?

Posted by on

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that gotĀ 5 achievements.

    Governor:

    An expert whose answer gotĀ voted for 20 times.

    Scholar:

    An expert who has written 20 answers of more than 400 characters.

  • Expert
  • 108 Answers

Should be a bolt where the hose enters the front caliper. just unhook and replace with new one. Be forewarned. When you change out the lines, you need to bleed the brakes as well.

Posted on Oct 07, 2009

Testimonial: "thank you for the simple yet helpful response to my question. You all have a wonderful day!"

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How to change a flywheel on a 84 bronco 2 standard transmition


is the flywheel worn out or just the ring gear, (starter gear)
first remove the trans mission then unbolt the flywheel, and replace
if only replacing the starter ring gear, use a soft hammer and bump it as you rotate the flywheel until it comes off, if the back side looks good heat it in the oven to 350 degrees and with gloves on run out and put it on the flywheel, it will go on easily, just hold it all the way on against the edge it rests on and turn it about 1/3 turn and hold for about 15 seconds and that's it, it will not come off unless you beat it off again

Mar 23, 2015 | 1984 Ford Bronco II

1 Answer

Does a 84 bronco 2 have a crank sensor


no use all efect switch on the distributor

Oct 20, 2014 | 1984 Ford Bronco II

1 Answer

What carburator is stock for 1984 ford bronco 2 2.8 liter


http://www.hotrodders.com/forum/carb-2-8-l-v6-1984-ford-bronco-ii-132065.html

according to the site, a <350cfm holley carb should fit right on the motor and give you no problems, this will provide some reliability and tunability as well as aftermarket support for your application compared to factory, they should be very easy carbs to find used on ebay and such

Mar 01, 2011 | 1984 Ford Bronco II

1 Answer

Can i put a 84 bronco 2 tranny mazda type 14 bolt pan in a 88 bronco 2 that originally had a 12 bolt pan both 4wd


well if it is a 1984 tranny it is a toyo koygo tk4 or tk5, which if mounted in the 84 bronco the transmission sets at a tilt, which means that the transmission crossmember bolts into the frame at a angle.. the mazda tranny was used in 88-90 the transmission crossmember sets straight across and bolts on to the frame on each side with one bolt.. with some major fabricating it is possible but to simply change out nope wont fit..

Jan 28, 2011 | 1988 Ford Bronco II

1 Answer

What is the firing order 1984 ford bronco 2 2.8 liter


Cylinder numbers (front-rear)
Left (driver's) side 4-5-6
Right side 1-2-3
Firing order 1-4-2-5-3-6

Jan 25, 2010 | 1984 Ford Bronco II

4 Answers

What is the firing order for a 1984 ford bronco 2


1-4-2-5-3-6
Now you need to know which cylinder is which. If you stand at the front of the truck looking at the engine, the number 1 cylinder is on the left closest to you. The left bank has cylinders 1-3-5 and the right bank has 2-4-6. So number 1 is at the left front and number 6 is at the right rear.

Jan 25, 2010 | 1984 Ford Bronco II

1 Answer

84 bronco 2 over heating


Check coolant level, then thermostat, then water pump circulation. If all are good then jump to head gasked, cracked head or block...

Dec 18, 2009 | 1984 Ford Bronco II

1 Answer

Drive belt configuration for 84 B II


Yours Maybe Missing But Ford Puts A Sticker On The Front Crossmember At The Radiator Somewhere Close To The Hood Latch It Shaws The Belt Routing For Your Vehicle's Engine Hope This Help's

Jul 16, 2009 | 1984 Ford Bronco II

1 Answer

84 ford bronco 2 thermostat


tha gasket goes on the housing, the copper side should go down.

Dec 29, 2008 | 1984 Ford Bronco

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

260 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

75797 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22114 Answers

fordexpert

Level 3 Expert

5495 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...