Question about 1997 Chevrolet S-10 Pickup

1 Answer

Replace broken turn signal

Replace broken hazard light switch

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Master
  • 11,896 Answers

Everything you will need you can find here:

http://www.ehow.com/videos-on_453_replace-turn-signal-switch.html

copy and paste in your address bar under new tab

Posted on Oct 06, 2009

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

The hazard back lights wont quit blinking when car is running even when i pull the fuse on a 2002 buick regal


What fuse are you pulling ?

Hazard Lamps
The hazard warning switch is part of the turn signal switch. The turn signal switch receives battery voltage at all times through the HAZARD SWITCH Fuse. When the hazard switch is placed in the HAZARD position, battery voltage is applied to the hazard lamp/turn signal lamp flasher. The hazard lamp/turn signal lamp flasher sends a turn signal flasher signal to the turn signal switch. The turn signal switch provides all of the turn lamps and turn indicators with the turn signal flasher signal, simultaneously flashing them on and off.

Turn Signal Lamps
The front turn signal lamps are made up of the front park/turn signal lamps and rear turn signal lamps. The front turn signal lamps flash with the rear turn signal lamps when a turn is initiated using the turn signal/multifunction lever. The turn signals will operate only with the ignition switch in the RUN position and will not operate during hazard flasher operation.
When the ignition is turned to the RUN position, battery voltage is supplied to the TURN SIGNAL Fuse. Battery voltage is then applied through the turn signal fuse circuit to the turn signal switch. When the turn signal switch is placed in the LH or RH position, voltage is supplied to the hazard lamp/turn signal lamp flasher. The hazard lamp/turn signal lamp flasher supplies a turn signal flasher signal to the turn signal switch. With the turn signal switch in the LH or RH position the corresponding turn signal indicator, rear turn signal, and front turn signal receive the turn signal switch signal and will flash. The front turn signals receive the turn signal switch signal from the turn signal switch via the BCM. The turn lamps are permanently grounded.

Replace the turn signal switch. Refer to Multifunction, Turn Signal, and Hazard Switch Replacement - On Vehicle in Steering Wheel and Column - Tilt.

Feb 11, 2017 | Buick Cars & Trucks

1 Answer

1996 Toyota Avalon turn signals don't work, but hazards do?


Turn signals and hazard lights are 2 totally different switches. You basically verified that the flasher unit works, but the turn signal switch is broken.

Mar 07, 2015 | 1996 Toyota Avalon

1 Answer

Hazard light not working


Replace the hazard switch. If it located in the steering column by the turn signal switch. You have to replace the turn signal switch. They are made together.

Feb 17, 2015 | 2006 Kia Rio

4 Answers

Turn signal lights don't work


The first place to start are fuses, check your owners manual for location, typically left side of dash.

The emergency (hazard) flashers and turn signals are on separate fuses and run through the hazard switch. If all the lights work when the hazard switch is on then the problem will likely be a blown turn signal fuse.

Other possibilities are the hazard switch itself is bad, the turn signal switch is bad or a broken wire, all of which require a meter (or test light) wiring diagram and knowledge of the circuit to test it - better to have it done.

Robert Grove
Mobile Mechanic Malibu 310 651 8020 Auto Truck RV Mobile Repair...

Aug 09, 2014 | 2002 Chevrolet Impala

1 Answer

How to fix no brake light issue on 1999 Expedition


Have you tried wiggling the hazard light switch? The brake light switch puts 12 volts to the hazard/turn signal switch,and the switch will apply this to both taillights.If you turn on the left or right turn signal,it will only route 12 volts to the other light.If you turn on the hazard lights,it will only allow the 3rd brake to come on due to the brake switch.Often.the hazard light/brake light contacts get corroded due to not being turned on and off regularly.Have someone watch the taillights(or use a mirror) to see if they come on when you wiggle the hazard switch.If it does,turn the hazard light switch on and of repeatedly to clean the contacts.

Jul 14, 2012 | 1999 Ford Expedition

1 Answer

I have a 90 montero and the brake lights and turn signals stopped working and I have replaced the fuses and can't figure it out.


my 91 Montero did the same thing, I finally traced it to a bad rocker switch for hazard lights. The switch was broken and it messed up brakes and turn signals. Check your switches that they work and rock properly. My hazard switch was binding turning on and off causing a short. Got a new hazard switch that worked freely and suddenly everything worked right. The problem drove me crazy, and I did replace the turn signal lever assembly first, brake switch, turn signal relay. I found dash switches on eBay.

May 22, 2012 | 1990 Mitsubishi Montero

1 Answer

I have no signals and when brakes lights are on, lose brake light to either side turn signal is set on


Hi!!

If you activate the turn signal switch and you step on the brake pedal, the turn switch (on the steering column) deactivates the brake light to make the signal light more visible. The bulb for the stop and turn lights is the same.

Turn hazard lights ON. If they don't blink, replace turn/hazard flasher, If one or more lights don't come on, replace bulb.

Check fuse and circuit wiring for broken or loose connections. If all looks fine, check following:

If front turn lights work fine, check brake/turn bulbs.

If turn lights come on but don't blink, replace turn signal/hazard flasher.

If front and back turn lights don't come on, replace switch on column.

Let me know how it worked out, Good Luck

Mar 24, 2010 | 1991 Plymouth Acclaim

2 Answers

Broken Hazards on 89 Ford Ranger


The hazard switch , turn signal switch , wiper switch are useually all one piece, Called a combo switch, They are known for going bad

Mar 13, 2010 | 1989 Ford Ranger

3 Answers

No turn signals or hazzards


first thing is replace both flashers one for signals and the other for hazards. if they still dont work then its your signal light switch, also check all fuses before you do anything.hope this helps.

Oct 20, 2009 | 1999 Chevrolet Lumina

Not finding what you are looking for?
1997 Chevrolet S-10 Pickup Logo

Related Topics:

97 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts

yadayada
yadayada

Level 3 Expert

75822 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8202 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...