Question about 2000 Ford Focus

1 Answer

How do you disconnect engine from transmission? Where is torque converter bolts? 2000 ford focus 2.0

Posted by on

Ad

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that gotĀ 5 achievements.

    Governor:

    An expert whose answer gotĀ voted for 20 times.

    Scholar:

    An expert who has written 20 answers of more than 400 characters.

  • Expert
  • 127 Answers

Get the front end up on some jack stands, take the starter out, and you can access torque converter nuts from starter hole. you will need to turn the engine by hand and have someone else hold the engine still while you undo the nuts. Once those nuts are off and every thing else is removed from the transmission (CV shafts, wire connectors, etc) remove the bell housing bolts (5 or 6 I think) and pull (may need to pry with a bar some) the trans away from the engine and let it down gently. I believe (although I don't do much transmission work) that you may need to remove the sub-frame a as well.

Posted on Oct 06, 2009

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How to install a torque converter in a 2000 2.5Lt on Ford ranger 2 wheel drive?


You need to remove the transmission to do this. Remove the inspection cover at the junction of the engine and transmission to get to the bolts to disconnect the torque converter from the drive plate (the part with teeth that the starter engages). Remove the driveshaft, then the transmission. The torque converter will come out with the transmission. Pull the old torque converter from the transmission, and install the new one. Ensure the torque converter goes all the way into the transmission/hydraulic pump. Reinstall the transmission, ensuring that the torque converter is still free to turn during the entire installation process, especially while drawing up the transmission to the engine. Once the transmission is bolted up, reinstall the bolts holding the torque converter to the drive plate. Reinstall the drive shaft and the inspection cover.

If you haven't done any major mechanical work on a car before, seek the help of someone who has. You will need a hoist or a jack and jack stands, and a good set of tools.

Nov 03, 2016 | Ford Cars & Trucks

3 Answers

How to remove and replace auto transmission ?


Its a big job gave you and example for neon

Jan 18, 2015 | 2001 Chrysler Voyager

1 Answer

How to remove 2000 ford fiesta 1400 gearbox


Make sure you cradle the Engine from above. Remove the CV Axles, disconnect the wires and transmission lines and then the 4 torque converter bolts, then the housing bolts and last the mounting bolts and reinstall in reverse order.

Sep 06, 2014 | Cars & Trucks

3 Answers

My Ford Focus 2006 4 cyc has an engine code PO741 on my OB2. What does that mean?


P0741 Torque convertor clutch circuit failure,it is located in the transmission valvle body, it is attatch to the valve body you can remove it seperately as long as your going to own the Ford focus you might as well get use to replacing these all the time,very common transmission issue with todays car. By the way it is sensitive to worn transmission fluid,when you dont service often these are suspectable to failure.

Apr 22, 2011 | Ford Focus Cars & Trucks

1 Answer

How do i change the starter on a 1997 buick park avenue?


Removal & Installation To Remove:
Starter 9306xg03.gif

  1. Before servicing the vehicle, refer to the service precautions in the beginning of this section
  2. Disconnect the battery negative cable
  3. Raise and support the vehicle
  4. Remove the transmission cooler line clip if necessary
  5. Remove the torque converter cover
  6. Disconnect the battery positive cable from the starter
  7. Disconnect the wire from the starter solenoid S terminal
  8. Remove the 2 starter motor mounting bolts and the starter motor
To Install:
  1. Install the starter motor
    • Torque the mounting bolts to 32 ft-lbs (43 Nm)
  2. Connect the battery positive cable to the starter
    • Torque nut to 12 ft-lbs (16 Nm) (1997-2000);
    • Torque nut to 89 in-lbs (10 Nm) (2001-2005)
  3. Connect the starter motor S terminal wire
    • Torque nut to 22 in-lbs (2.5 Nm)
  4. Install the torque converter cover
    • Torque the bolts to 115 in-lbs (13 Nm)
  5. Attach the transmission cooler line clip
  6. Lower the vehicle
  7. Reconnect the negative battery cable
prev.gif next.gif

Dec 09, 2010 | Buick Park Avenue Cars & Trucks

1 Answer

How to remove a transmission for a 2002 GMC Yukon


Removal & Installation 4L60E/4L65E To Remove:
  1. Remove or disconnect the following:
    • Transmission fluid
    • Transmission oil level indicator tube and seal from the transmission
    • Plug the oil level indicator tube opening in the transmission.
    • Remove or disconnect the following:
    • Shift cable end from the transmission shift lever ball stud
    • If equipped with a transfer case, remove the front propeller shaft.
    • Rear propeller shaft.
  2. Plug the transmission oil cooler line connectors in the transmission case.
  3. Remove or disconnect the following:
    • Starter motor.
    • Transfer case, if equipped.
  4. Support the transmission with a transmission jack.
  5. Remove the transmission mount nuts.
  6. Remove the transmission crossmember.
  7. Remove or disconnect the following:
    • Torque converter access plug 4L60E/4L65E removal 9308kg37.gif

    • Flywheel to torque converter bolts
    • The two bolts securing the transmission rear mount to the transmission
    • The transmission vent hose, fuel lines, and the wiring harness from the transmission
    • The stud and the bolt securing the transmission to the engine
    • The six studs and one bolt securing the transmission to the engine. Install tool J21366 onto the transmission bell housing to retain the torque converter. Pull the transmission straight back.
    • The transmission from the vehicle
  8. Flush the transmission oil cooler and cooling lines when you remove the transmission.
To Install:
  1. Install or connect the following:
    • Tool J21366 onto the transmission bell housing to retain the torque converter.
    • Support the transmission with a transmission jack.
  2. Raise the transmission into place and remove the tool from the transmission.
  3. Slide the transmission straight onto the locating pins while lining up the marks on the flywheel and the torque converter. The torque converter must be flush onto the flywheel and rotate freely by hand.
  4. Install or connect the following:
    • Six studs and one bolt securing the transmission to the engine. Tighten the studs and the bolt to 50 Nm (37 ft. lbs.).
    • Stud and bolt securing the transmission to the engine. Tighten the stud and the bolt to 50 Nm (37 ft. lbs.).
    • Flywheel to torque converter bolts. Tighten the stud and the bolt to 46 Nm (63 ft. lbs.).
    • Torque converter access plug.
    • Transmission vent hose, fuel lines, and the wiring harness to the transmission.
    • Two bolts securing the heat shield to the transmission. Tighten the bolt to 17 Nm (13 ft. lbs.).
    • Two bolts securing the transmission rear mount to the transmission. Tighten the bolts to 18 ft. lbs. (25 Nm).
    • Install the transmission crossmember. Tighten the nuts and bolts to 70 ft. lbs. (95 Nm).
  5. Remove the transmission jack from the transmission.
  6. Unplug the transmission oil cooler line connectors in the transmission case.
  7. Install or connect the following:
    • Starter
    • Transmission oil cooler lines to the transmission
    • If equipped with a transfer case, install the front propeller shaft.
    • The rear propeller shaft
    • The shift cable end to the transmission shift lever ball stud
  8. Unplug the oil level indicator tube opening in the transmission.
  9. Install the transmission oil level indicator tube and seal to the transmission.
  10. Tighten the oil pan bolts and fill the transmission with transmission fluid.
  11. Lower the vehicle.
4L80E/4L85E To Remove:
  1. Remove or disconnect the following:
    • Transmission fluid
    • Transmission oil level indicator tube and seal from the transmission
  2. Plug the oil level indicator tube opening in the transmission.
  3. Remove or disconnect the following:
    • Shift cable from the transmission shift lever ball stud
    • If 4WD vehicle, remove the propeller shaft.
    • If RWD vehicle, remove the propeller shaft.
    • The transmission oil cooler lines from the transmission
  4. Plug the transmission oil cooler line connectors in the transmission case.
  5. Remove or disconnect the following:
    • Starter motor
  6. Support the transmission with a transmission jack.
  7. Remove or disconnect the following:
    • The two bolts securing the heat shield to the transmission
    • The transmission vent hose, fuel lines, and the wiring harness from the transmission
    • One nut and one bolt securing the transmission brace to the engine bracket and transmission
    • The two bolts securing the torque converter cover to the engine
    • The four bolts securing the torque converter cover to the transmission
    • The six flywheel to torque converter bolts
    • The two bolts and nut securing the transmission rear mount to the transmission
    • The stud and the bolt on the right side securing the transmission to the engine
    • The remaining six studs and the one bolt securing the transmission to the engine
    • Tool J21366 onto the transmission bell housing to retain the torque converter
    4L80E/4L85E removal 9308kg36.gif

  8. Pull the transmission straight back. Remove the transmission from the vehicle.
  9. Flush the transmission oil cooler and cooling lines when you remove the transmission.
To Install:
  1. Install or connect the following:
    • Tool J21366 onto the transmission bell housing to retain the torque converter
  2. Support the transmission with a transmission jack.
  3. Raise the transmission into place and remove the tool from the transmission.
  4. Slide the transmission straight onto the locating pins while lining up the marks on the flywheel and the torque converter. The torque converter must be flush onto the flywheel and rotate freely by hand.
  5. Install or connect the following:
    • Six studs and one bolt securing the transmission to the engine. Tighten the studs and the bolt to 50 Nm (37 ft. lbs.).
    • The stud and bolt on the right side securing the transmission to the engine. Tighten the stud and the bolt to 50 Nm (37 ft. lbs.).
    • Six flywheel to torque converter bolts. Tighten the bolts to 60 Nm (44 ft. lbs.).
    • The two bolts securing the torque converter cover to the engine. Tighten the bolt to 50 Nm (37 ft. lbs.).
    • The four bolts securing the torque converter cover to the transmission. Tighten the stud and the bolt to 33 Nm (24 ft. lbs.).
    • The transmission vent hose, fuel lines, and the wiring harness to the transmission.
    • The two bolts securing the heat shield to the transmission. Tighten the bolt to 17 Nm (13 ft. lbs.).
    • The two bolts and nut securing the transmission rear mount to the transmission. Tighten the bolts and nut to 25 Nm (18 ft. lbs.).
    • The flywheel to torque converter bolts.
    • One nut and one bolt securing the transmission brace to the engine bracket and transmission. Tighten the bolts and nut to 50 Nm (37 ft. lbs.).
  6. Remove the transmission jack from the transmission.
  7. Install or connect the following:
    • Starter motor
  8. Unplug the transmission oil cooler line connectors in the transmission case.
  9. Connect the transmission oil cooler lines to the transmission.
  10. Install or connect the following:
    • The transfer case
    • The rear propeller shaft
    • The shift cable end to the transmission shift lever ball stud
  11. Unplug the oil level indicator tube opening in the transmission.
  12. Install the transmission oil level indicator tube and seal to the transmission.
  13. Tighten the oil pan bolts and fill the transmission with transmission fluid.
  14. Lower the vehicle.
prev.gif next.gif

Oct 12, 2010 | 2002 GMC Yukon XL

1 Answer

Changing a transmission in a 1989 Buick Electra Park Avenue


Transmission REMOVAL & INSTALLATION
  1. Disconnect the negative battery cable. Open the hood and place protectors on the fenders. Remove the air cleaner assembly.
  2. Disconnect the detent cable at its upper end.
  3. Remove the transmission oil dipstick, and the bolt holding the dipstick tube if it is accessible.
  4. Raise the vehicle and safety support it with jackstands. NOTE: If a floor pan reinforcement is used, remove it if it interferes with driveshaft removal or installation.
  5. Disconnect the speedometer cable at the transmission.
  6. Disconnect the shift linkage at the transmission.
  7. Disconnect all electrical leads at the transmission and any clips that hold these leads to the transmission case.
  8. Remove the flywheel cover and matchmark the flywheel and torque converter for later assembly.
  9. Remove the torque converter-to-flywheel bolts and/or nuts.
  10. On gasoline engine vehicles, disconnect the catalytic converter support bracket.
  11. Remove the transmission support-to-transmission mount bolt and transmission support-to-frame bolts, and any insulators (if used).
  12. Position a transmission jack under the transmission and raise it slightly.
  13. Slide the transmission support rearward.
  14. Loosen the transmission enough to gain access to the oil cooler lines and detent cable attachments.
  15. Disconnect the oil cooler lines and detent cable. Plug all openings.
  16. Support the engine and remove the engine-to-transmission bolts.
  17. Disconnect the transmission assembly, being careful not to damage any cables, lines or linkage.
  18. Install a C-clamp or torque converter holding tool onto the transmission housing to hold the converter in the housing. Remove the transmission assembly from the vehicle (a hydraulic floor jack is best for this). To install: Fig. 1: Transmission oil cooler lines 85847023.gif

  19. Install the transmission assembly into the vehicle (a hydraulic floor jack is best for this). When installing the flex plate-to-converter bolts, make sure that the weld nuts on the converter are flush with the flex plate and that the converter rotates freely by hand. Coat the threads with thread locking compound, hand-start the three bolts, tighten them finger tight and torque them evenly to 35 ft. lbs. (48 Nm).
  20. Support the engine and install the engine-to-transmission bolts. Torque the bolts to 40 ft. lbs. (54 Nm).
  21. Connect the oil cooler lines and detent cable.
  22. Slide the transmission support forward.
  23. Position a transmission jack under the transmission and raise it slightly.
  24. Install the transmission support-to-transmission mount bolt and transmission support-to-frame bolts, and any insulators (if used).
  25. On gasoline engine vehicles, connect the catalytic converter support bracket.
  26. Install the flywheel cover.
  27. Connect all electrical leads to the transmission and any clips that hold these leads to the transmission case.
  28. Connect the shift linkage at the transmission.
  29. Connect the speedometer cable at the transmission.
  30. Check to see if all under vehicle components and fasteners are properly installed and torqued.
  31. Lower the vehicle safely.
  32. Install the transmission oil dipstick, and the bolt holding the dipstick tube if it is accessible.
  33. Connect the detent cable at its upper end.
  34. Connect the negative battery cable. Recheck all procedures for completion of repair. Close the hood and remove the protectors on the fenders.
  35. Install the air cleaner assembly. Refill the transmission with fluid as outlined in the "Oil Pan'' section in this chapter.
  36. Start the vehicle and check operation. prev.gif next.gif

Sep 25, 2010 | 1989 Buick Electra

1 Answer

How do you pullout a transmission on a 2000 dodge caravan


transmisssion comes out from under vehicle.jack up vehicle or place on lift if available. first remove front tires, in center of brake rotors remove large nut in center. disconnect lower control arms on left and right. pull both left and right drive axles. disconnect all cables connected to transmission, disconnect two transmission cooling lines, remove lower frame connected to vehicle body and transmission and engine. remove inspection cover on transmission, remove eight bolts around outer edge of transmission, remove four bolts that connect torque converter to flywheel.slide transmission out horizontally to remove.

Jun 13, 2010 | 2000 Dodge Caravan

1 Answer

Starter for kia sportage 2000


  1. Before servicing the vehicle, refer to the precautions at the beginning of this section.
  2. Drain the engine oil.
  3. Remove or disconnect the following:

    Negative battery cable Intake manifold bracket upper bolts Clutch release cylinder and move it aside, if equipped Intake manifold bracket lower bolts and remove the bracket Starter from the clutch, manual transmissions only Starter from the torque converter, automatic transmissions only Starter electrical connectors Move the transmission wire harness aside Starter


    0900c152801b0603.jpg enlarge_icon.gifenlarge_tooltip.gif Fig. Exploded view of the starter

To install:
  1. Install or connect the following:

    Starter to the engine well Starter electrical connectors Lower intake manifold bracket and install the upper bolts Starter into position. When aligned properly torque the bolts to 40 ft. lbs. (54 Nm). Torque the intake manifold bracket bolts to 40 ft. lbs. (54 Nm). Properly position the clutch release cylinder, if equipped. Torque the bolts to 40 ft. lbs. (54 Nm). Torque the intake manifold bracket upper bolts to 40 ft. lbs. (54 Nm). Negative battery cable

Jun 28, 2009 | 2000 Kia Sportage

Not finding what you are looking for?
2000 Ford Focus Logo

736 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

76848 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22246 Answers

fordexpert

Level 3 Expert

5546 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...