Question about 1988 Toyota Tercel 2 Door

1 Answer

Changing the starter

Whats the easist way to change one? from above or below?

Posted by on

  • paksu508 Nov 21, 2009

    how much the sun roof rubber seals for toyota wish,

    and where can i get it..

×

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    President:

    An expert whose answer got voted for 500 times.

  • Toyota Master
  • 1,564 Answers

Depending on the amount of obstuction from the exhaust pipes and the transmission lines it is often necessary to remove the dismounted starter from the top.

Posted on Oct 06, 2009

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

07 ram 5.7 No start 1 click Battery cleaned charged up tried on boost - still 1 click . New starter- ran Jumper wire to starter from battery- 1 click. What can it be ?


If the battery connections at the starter are secure it is likely the solenoid is defective on the new starter.

When attempting to start monitor the battery voltage. If the voltage only changes sightly still above 12 volts it is likely that the starter motor is not getting power. Confirm that the starter solenoid is being powered when attempting to start.

If
  • all battery connections to the starter are secure
  • and power is applied to the starter solenoid
  • and no crank above 12 volts
these combined conditions will confirm that the new starter is defective.


26375961-eslp3us1ub1u3afrhtff0zvp-3-0.jpg

26375961-eslp3us1ub1u3afrhtff0zvp-3-2.jpg Hope this helps?

Nov 28, 2016 | Cars & Trucks

1 Answer

Need to change my alternator in 1990 cutlass ciera need instructions


MY Alternator is not below it on the top of my 3.3 olds 1990.they are talking about the starter on the fix above not very helpful

Aug 05, 2011 | 1990 Oldsmobile Cutlass Ciera

1 Answer

How do I change the starter?


Hi,

here is for the Removal & Installation
1. Disconnect negative battery cable. Remove two upper bolts from intake manifold bracket. Raise and support vehicle. Raise and support vehicle. On M/T, remove clutch slave cylinder from side of clutch housing and push it aside.
2. On all models remove lower intake manifold bracket bolts and bracket. Remove two upper starter bolts and a lower bolt. Pull starter from clutch (M/T)or converter (A/T) housing and prop in place. From above, disconnect starter solenoid "S" and "B" terminal connectors. From below, push transmission harness aside and remove starter.
3. To install, reverse removal proceedure. Rotate starter to provide proper clearance. Torque all nuts and bolts to specifications.


Good luck!

Aug 06, 2010 | 1999 Kia Sportage

1 Answer

1994 S10 Broken key in pass. side lock-Easist way to


You could try using two needles and see if you can slide them in above the and or below the broken key and apply some leverage to see if you can pop it out or try a powerful magnet. If need be, you'll need to remove screws that are by the door handle, arm rest, under door and side of door and then gently pull back on the panel as there will also be retaining clips attached and you don't want to break them. You'll need to lift the door panel upwards in order to get it off the window ledge. Then you can pull back the weather seal (can't reuse it, but it's not that important) and you will be able to access everything inside the door, The lock will be held down by a bolt that you can reach relatively easily. The unscrew the bolt and the cylinder will slide it... it may fall down into the door though, but you can still get to it

Aug 17, 2009 | 1994 Chevrolet S-10

3 Answers

How do you change a starter on 2002 cadillac deville?


easy as, 2 bolts at the front and 3 wires at the back remove all and it should come free, the motor is at the front of the tranny it is attached to the flywheel, disconnect battery first

Jun 23, 2009 | 2001 Cadillac DeVille

1 Answer

Car would not start, changed 5yr old battery. 1wk later same thing. alternator checked out ok. belt and tensioner ok. Seems to happen when car is warm. any ideas?


Same thing happened to mine. Turned out to be my starter. If you know where the starter is and the starter cilinoid (sp), take a metal rod (think the detachable handle for a nice automobile jack) and tap on it from above or below (it's kinda deep in there) and have someone try to start it while doing that. If that solves your problem, your starter's your problem. (Even if that trick doesn't work, it's still possible your starter's your problem.)

Jun 06, 2009 | 2001 Ford Taurus

1 Answer

Daewoo Nubira Starter Motor Refit.


changed a clutch on one of these a few weeks ago and cant remember what i done ,old timers i think ?? not sure but its from below with a rear support bracket ,and a inlet manifold stay bar ,,,3/8 drive socket set with a knuckle and 3 long extension bars to get to top inside bolt as well i think ?? honestly cant remember ,i work on all makes and cant remember every one

Apr 14, 2009 | 1999 Daewoo Nubira

1 Answer

I need to change my starter on a 1991 mercury sable


Starter are one of the easier mechanical engine parts to change.

1) DISCONNECT THE BATTERY.
2) Disconnect the electrical cable running to the solenoid on the starter.
3) Remove the two bolts holding the starter in place.
4) Pull the starter out.

To install another starter, do the above steps in reverse order in reverse.

Apr 04, 2009 | 1991 Mercury Sable

2 Answers

Truck has good battery but will not turn over


FROM LUSTYKID:

Ensure fuse link in system is not burned out first.

Check ignition switch circuit, ensure the ignition switch works, if good then you need to check starter solenoid to make sure it works. If solenoid is not the type above the starter (Fords have it separate) change solenoid, If its with the starter, change starter.

If you hear a click when you turn to start, and no turn over,,,change the starter.

Dec 26, 2008 | Chevrolet 1500 Cars & Trucks

4 Answers

Don't know where the fuel filter is located on my 1993 toyota 4/x4 pickup


I believe that it is located on the passenger side of the motor right above the starter.

It probably easier to change it if you take off the front tire and work through the wheel well

Jul 31, 2008 | 1993 Toyota Pickup

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

74 people viewed this question

Ask a Question

Usually answered in minutes!

Top Toyota Experts

yadayada
yadayada

Level 3 Expert

76846 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22246 Answers

Jeffrey Turcotte
Jeffrey Turcotte

Level 3 Expert

8560 Answers

Are you a Toyota Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...