Question about Ford Econoline

1 Answer

I am installing an Offenhouser intake manifold on a Ford inline-6

I am installing an Offenhouser intake manifold on my Ford inline 240cu.in. six cylander motor. The intake/exhaust is a split design(2 piece). How do you install this properly? Do I bolt it to the head, and then tighten the upper/lower manifolds together, or tighten them together and then bolt to the head? It looks like I need to bolt to head, and then tighten both halves together, in order to get a good seal on the head.

Posted by on

  • 1 more comment 
  • Anonymous Mar 14, 2014

    Install instruction exhaust intake maniafold 1969 f 100 inline 6

  • Anonymous Mar 14, 2014

    Need diagram for upper and lower bolt tightening sequence.

  • Anonymous Mar 14, 2014

    Need diagram for upper and lower bolt tightening sequence.

×

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Brigadier General:

    An expert that has over 10,000 points.

  • Master
  • 7,353 Answers

Put the halves together leave bolts snug, then bolt it to the head, now go back and tighten the halves together,

Posted on Oct 07, 2009

Testimonial: "thanks for the prompt answer/help."

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

What is the location of the iat scensor on my 1995 ford e 250 4.9 L inline six


Intake air temp sensor should be in the air filter box side I believe.

Jan 19, 2015 | Ford Cars & Trucks

Tip

Cheapest Real Power Gain For a Jeep with the 4.0 L6


Hello. If you're anything like me, you're always looking to squeeze a little bit more power out of your ride. Whether it be for racing, comfort, or even safety, more power is always better, especially without sacrificing fuel economy, which we all know is a huge factor.

I have a power improvement secret for all Jeep vehicles prior to 1999 (some up to 06.)

If you replace your factory intake manifold with one from a newer Jeep, bam! you get more power. Here are the specifics:

In 1998, when the standards for fuel efficiency were increasing, and the Grand Cherokee was about to debut its newest generation, something had to be done with the 4.0 inline six cylinder that Jeep used across its lineup. It was not going to meet EPA regulations without some tweakage. So, one of the major points of change was the intake manifold.

e1e99b6.jpg
This is an actual image from my install. The top intake manifold is off of a 2002 Jeep Grand Cherokee with the 4.0. It has been painted with high-heat black. The bottom one is off of my 1996 Jeep Grand Cherokee with the 4.0. Notice the difference in design. The newer manifold is less angular, allowing more air to enter the engine without getting caught up in the manifold. This free flowing design helps free up a few hidden horsepower. For what I paid ($50,) and the increase I felt (upwards of 8hp,) this is definitely the most cost effective, and little known about modification for increasing power in your Jeep 4.0.

on Jul 10, 2010 | Jeep Grand Cherokee Cars & Trucks

1 Answer

I've acquired a chevy cosworth vega sn# 1221.the


Why not make a manifold & go with fuel injection?
When you say webers are pricy, your working on a
rare project
Those usually don't have a budget & the people have deep
pockets that play with those hobbies

Jul 26, 2013 | Cars & Trucks

1 Answer

What is the smog equipment part between the carburetor and intake manifold on a 1982 Ford Fairmont Futura straight six engine called?


I believe your talkng about an exhaust gas recirculation (EGR) plate. This is a ported plate that allow exaust gasses to be recirculated back into the intake stream. Attached to it is the EGR valve itself. Here is a pic diagram showing the assembly. The plate is listed here as a carburator spacer.

uhotrodshop.jpg

May 09, 2011 | Ford Fairmont Cars & Trucks

1 Answer

Trying find out which wires goes were on a 1992 ford f150 with a 300 six


If it's ignition wires that you're speaking of, and you have not removed the distributor, here is the procedure. With the distributor cap removed, bump the starter just enough to note the direction of the rotor, (usually clockwise) Bring the #1 piston to Top Dead Center on the compression stroke. Cylinder #'s are stamped or raised on the intake manifold. Where the rotor is pointing is where you begin wiring with the # 1 cylinder. Then follow the firing order which is also on the intake manifold in the direction of the rotor movement noted earlier.

May 04, 2011 | Ford F-150 Cars & Trucks

1 Answer

Where is the starter located in a BMW Z3 engine?


if it's the 2.8L inline six...you gotta real problem. might be able to get it from the bottom but there's also a thread on replacing the starter by taking the intake manifold off.

Aug 09, 2010 | 1999 BMW Z3

2 Answers

I mixed up my firing order on my ford F-150 300 engine i need the correct firing order.


For the Ford 300 inline 6 cylinder the firing order is: 1-5-3-6-2-4

Hope this helps

Jun 26, 2010 | Cars & Trucks

2 Answers

How to replace exhaust manifold gasket 1989 jeep wrangler 4.2


I also have an '89 Wrangler with a 4.2 liter inline six. I'm afraid that the spark plugs aren't on the same side as the manifolds. Mine is being a pain in the *** for me. The intake is lining up fine but the exhaust is off by about 1/4 of an inch in the way of a bolt. Was hoping for some solutions, left disappointed.

Apr 26, 2010 | 1989 Jeep Wrangler

1 Answer

Changed plugs,wires,cap,rotor,and all filters.


spray some non flammable cleaner around intake manifold and see if engine speed changes. vacuum leak.

Feb 19, 2010 | Ford F-150 Cars & Trucks

2 Answers

What is the firing order for a 2006 ford tauras


Sir,
There are two firing order sequences for the FORD V-6. It depends on which engine you have. The first is 1-4-2-5-3-6. The second is 
1-4-2-3-5-6. The in-line six cylinder engines use: 1-5-3-6-2-4. You should look at the intake manifold to see which firing order your car uses. The firing order is normally stamped or embossed on the top of the intake manifold.


Link 1
Thanks Good Luck
Appreciate to rate as "Fixya"

Mar 07, 2009 | 2006 Ford Taurus

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

179 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

75797 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22114 Answers

fordexpert

Level 3 Expert

5495 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...