Question about 2000 Ford Taurus

1 Answer

Why, after changing the blend door actuator, does it still blow warm air?

Posted by on

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Corporal:

    An expert that hasĀ over 10 points.

    Problem Solver:

    An expert who has answered 5 questions.

  • Contributor
  • 5 Answers

Check all the air hose up to that point look to see if all hose is intack and put to gether right look for holes and cloges

Posted on Oct 06, 2009

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I have a Jeep Liberty and the heater only blows like warm air. I have replaced the thermostat and flushed the heater core and still no change. What could be wrong?


Blend door may be sticking thus mixing too much cold air with the hot. Bad blend door actuator, vacuum leak or blend door seal is bad.

Feb 19, 2015 | Jeep Cars & Trucks

1 Answer

Replace blend door actuator motor


Could be, check the door and see if it works correctly

Aug 17, 2013 | Mitsubishi Cars & Trucks

1 Answer

Heater blows cold air


Air Temperature Control Blend Door Failure No Heat

In all modern cars there is a tiny DC electric motor driven gear drive that moves a plastic door that blends heated and cooled air from the AC and the heater core, this is called (interestedly enough) the air temperature control blend door actuator. The motor that moves this door fails because the door starts sticking from warping, most common complaint is no heat but it can be no AC as well. To replace these parts (blend door and blend door actuator) you must remove the entire dash from the car. Always have this problem confirmed by a dealer or qualified repair shop as it is a very expensive repair.

Nov 01, 2012 | Pontiac Cars & Trucks

2 Answers

Air conditiner cools on right side but not on left side


It can be issue with blend door actuator or vacuum leak or loose vacuum hose connection.
I suggest you few help links.Click the link below and follow the troubleshooting.
-----
A/C Blows Warm? http://whoisbyme.blogspot.in/2012/06/2005-chrysler-pt-cruiser-ac-blows-warm.html

----------
A/C blows Cold From Defrost Vent Only? http://whoisbyme.blogspot.in/2012/06/2009-mercury-grand-marquis-ac-blows.html
-----------
A/c Blows Warm on driverside? http://whatisbyme.blogspot.in/2012/06/2007-kia-spectra-ac-blows-warm.html

-----------
A/C compressor clutch won't engage http://schematicsdiagram.blogspot.in/2012/04/2000-cadillac-deville-ac-compressor.html

---------------
Ford : A/C blows Warm? http://whoisbyme.blogspot.in/2012/06/2007-ford-freestyle-ac-blows-warm.html

----------
Thanks.

Jun 26, 2012 | 2005 Ford Five Hundred

1 Answer

My 2002 ford explorer the temp. Control knob when you change it it makes a loud clicking sound and it will no longer blow cold air only hot.


there is an actuator that controlls a blend door that is called a blend door actuator. This "door" is inside the evaporator case and it opens and closes to divert air over either the evaporator (for air conditioning) or the heater core (for heat) and can be somewhere in between for warm air. your temp knob sends an electric signal to this actuator to controll that door. the actuator has plastic gears inside of it that can become stripped of its teeth causing a "tapping" sound. These trucks comonly have this problem. The actuator is screwed on to the evaporator case and the blend door actuator is a mounted on top either behind the radio or the glove box. It;s about the size of a deck of cards

Dec 18, 2011 | 2002 Ford Explorer

1 Answer

It blows cold air out the driver side vents instead of warm air when the heat is turned up


Hello,
An all too common problem is the heat/air blend door in the climate control duct system. The blend door is either stuck, or you could have a bad actuator, ( the actuator is the device that moves the blend door based on your setting.)

I would likely have that checked first.

I hope this helps you.

Feb 10, 2011 | 2003 Hummer H2

2 Answers

2004 f350 ford heater blows cool air but hoses are both warm-where do i start looking


check to see if the blend door is moving where you change the temperature setting. I think your blend door is behind the glove box. Here are instructions for removing the actuator. Take it off, plug it back in and see if the motor rotates. Also check to see if you can rotate the blend door by hand. If you can rotate it by hand, the motor is probably broken of the gears are stripped. Let me know if you have questions.
  1. Release the stops and lower the glove compartment door.
  2. Disconnect the connector.
f4b0b74.gif Fig. Blend door actuator-F-250 & 350


  1. Remove the two screws. Rotate the blend door actuator and bracket assembly. Remove the electronic blend door actuator and bracket assembly.
  2. To install, reverse the removal procedure.

Oct 17, 2010 | 2004 Ford F350

3 Answers

Car warms up just fine but the heater blows cold air


both hoses is hot signifies thatcoolant circulation is just fine check the blend door actuator it might be stuck.pan the heater temp controller from hot to cold do you feel any change in temp of the air from the blower?if you dont feel any change check the blend door actuator

Jan 11, 2010 | 2002 Ford Taurus

2 Answers

Heater blows cold air ac blows warm air


Your problem is the air temp control blend door actuator is defective and not controlling temp u set. to change/access this part the dash assembly must be removed from the car.

Mar 24, 2009 | 1998 Ford Taurus

2 Answers

Heating system only blows out hot air through the vents


I would look at the air blend doors first, it sound like they are not working or your control in the dash is not working send a signal to them. they work by changing the air from hot to cold or in between.

Avalanche, Sierra And Silverado
  1. Remove the floor air outlet duct extension (1) from the floor duct (2). 0900c152801c9c8a.jpgRemove the floor air outlet duct extension (1) from the floor duct (2)
  2. Disconnect the electrical connection at the blend door actuator (10). 0900c152801c9c8b.jpgBlend door actuator and related components
  3. Remove the blend door actuator mounting screws from the HVAC module.
  4. Remove the blend door actuator as an assembly with the actuator cam. 0900c152801c9c8c.jpgRemove the blend door actuator mounting screws from the HVAC module
To install:
  1. Install the blend door actuator as an assembly with the actuator cam.
    1. Line up the heater/defroster valve lever with the blend door actuator cam slot.
    2. Line up the A/C valve lever with the blend door actuator cam
  2. Install the blend door actuator mounting screw to the HVAC module.
    1. Tighten the blend door actuator mounting screw to 14 inch lbs. (1.6 Nm).
  3. Connect the electrical connection at the blend door actuator (10). 0900c152801c9c8b.jpgBlend door actuator and related components
  4. Install the floor air outlet duct extension (1) to the floor air duct (2).
C/K Series
  1. Disconnect the electrical connector to the mode actuator that is located on the left side of the air distribution case.
  2. Remove the screws.
  3. Remove the adjuster links from the control lever.
  4. Remove the mode actuator.
  5. Adjust the mode actuator by completing the following steps:
    1. Connect the electrical connector to the actuator.
    2. Turn the ignition switch to the RUN position. Allow the self-positioning of the actuator.
    3. Turn the ignition switch to the OFF position.
    4. Remove the actuator from the electrical connection. 0900c152801c9c8d.jpgBlend door actuator-C/K Series
To install:
  1. Install the mode actuator.
  2. Install the screws.
  3. Install the adjuster links to the control lever.
  4. Connect the electrical connector.
  5. Test the circuit operation

Nov 27, 2008 | 2001 Chevrolet Silverado

Not finding what you are looking for?
2000 Ford Taurus Logo

Related Topics:

167 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

75807 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22133 Answers

fordexpert

Level 3 Expert

5495 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...